UltraBlend BL935E - Blender TEFAL - Free user manual and instructions

Product Type	Blender
Brand	Tefal
Model	UltraBlend BL935E
Capacity	2 L (maximum level), recommended 1 L for foamy preparations
Speed Settings	10 speed levels (1-10), plus pulse
Preset Programs	Smoothie, Hot Soup, Sorbet, Autoclean
Display	LCD screen with time and speed settings
Control Panel	Power button, Start button, Time settings, Speed settings (1-10), Pulse, Program buttons
Jug Material	Plastic (not specified, but typical)
Blade Material	Stainless steel (not removable, sharp)
Safety Features	Blender only starts when jug is correctly positioned; overload protection; lid must be locked
Maximum Hot Liquid Temperature	80°C (to avoid steam ejection)
Frozen Food Size Limit	Smaller than a walnut
Cleaning	Jug, lid, measuring cap dishwasher safe; silicone gasket hand wash only; motor unit wipe with damp cloth
Autoclean Program	150 ml water + 1 drop of detergent, runs for approx. 1 min 30
Accessories Included	Jug, lid, measuring cap, pusher, removable silicone gasket
Overload Protection	Yes – motor shuts off if overloaded; let cool 15-20 minutes
Maximum Continuous Operation	Less than 3 minutes per cycle; after 2 cycles, let cool to ambient temperature (about 2 hours)
Recommended Recipes	Carrot soup, fruit smoothie, hot soup, strawberry sorbet
Warranty	Refer to warranty leaflet (not specified)

Frequently Asked Questions - UltraBlend BL935E TEFAL

How do I start the blender?

Place the jug correctly on the motor unit, lock the lid, plug in, press the power button, then select a program or manual settings and press the start button.

What is the maximum capacity of the jug?

The maximum capacity is 2 L. For foamy preparations, it is recommended to half-fill (1 L).

Can I add ingredients while blending?

Yes, remove the measuring cap from the lid and add ingredients through the feeder hole. Be careful of splatter.

How do I clean the blender?

The jug, lid, and measuring cap are dishwasher safe. The silicone gasket must be hand washed. The motor unit can be wiped with a damp cloth. Do not immerse the motor unit in water. You can also use the Autoclean program.

What does the Autoclean program do?

Add 150 ml of water and a drop of washing-up liquid, then run the Autoclean program. It runs for about 1 minute 30 seconds at alternating speeds.

What should I do if the blender stops during operation?

This may be due to overload protection. Switch off the appliance, unplug it, let it cool for 15-20 minutes, then plug in again and resume blending.

Can I blend hot liquids?

Yes, but the liquid temperature must not exceed 80°C to avoid sudden steam ejection. The Hot Soup program is designed for pre-cooked vegetables and broth.

Is the blender suitable for crushing ice?

Yes, but frozen foods must be smaller than a walnut. Use the Sorbet program or pulse function.

Why does the blender not start?

Check that the plug is connected, the jug is correctly positioned on the motor unit, the power switch is on, and the lid is locked. If there is a software bug, unplug and wait a few minutes.

Can I remove the blades for cleaning?

No, the blades are not removable and are extremely sharp. Clean the jug carefully without touching the blades.

USER MANUAL UltraBlend BL935E TEFAL

DESCRIPTION OF THE APPLIANCE

1. Measuring cap
2. Lid
3. Jug
4. Removable silicone gasket
5. Motor unit
6. Pusher
7. Power button

A. Screen
B. Start button
C. Time settings

D. Speed settings 1-10
E. Smoothie program
F. Hot Soup Program
G. Pulse button
H. Sorbet Program
I. Autoclean Program

On LCD screen :

“H” represents the last and highest speed (10)

CAUTION: the safety precautions are part of the appliance. Read them carefully before using your new appliance for the first time. Keep them in a place where you can find and refer to them later on.

Warning:

The appliance will only start if the jug is correctly positioned on the motor unit (5).

BEFORE USING YOUR APPLIANCE FOR THE FIRST TIME

- Before using your appliance for the first time, hand-wash the parts that come into contact with food (jug, lid and measuring cap) in warm soapy water except for the motor unit.

ATTENTION: DO NOT IMMERSE THE MOTOR UNIT/CONTROL PANEL OR PUT IT UNDER WATER OR ANY OTHER LIQUID. Clean with a damp cloth and dry it carefully. CAUTION: The blades are extremely sharp and not removable.

• Make sure all the packaging has been removed before operating the appliance.
• Do not operate the blender if the lid is not in place.

USING YOUR APPLIANCE

• Put the appliance on a flat, stable, heat-resistant surface away from sources of heat or water splashes.
• Make sure the silicone gasket is in place on the motor unit. Position the jug correctly on the motor unit.
• Add the ingredients into the assembled jug without exceeding the maximum level indicated: 2L. It is recommended to half-fill the jug (1L) for foamy food.
  • After making hot soup, wait until the jug cools down between 2 recipes.
• Less than 3 minutes of mixing are enough to blend liquids for most of the recipes.

• Lock the lid on the jug. Place the measuring cap in position on the lid and lock it by rotating it.

• To add ingredients while blending, remove the measuring cap from the lid and add the ingredients through the feeder hole. Beware of the risk of spatter.

• Plug in the blender and press on the power button (7) a the bottom right of the appliance. The product makes a beep and the screen lights up in grey.
• Press on the Start button and the screen lights up in blue.
• Select your program or manual settings (time and speed) and press the start button. Wait for the blender to stop automatically. If you want to stop the blender before the automatic end of the program, press on the start button.
• Do not shake the motor unit or the jug when the blender is in use.
• When you use the pusher or the measuring cap, hold the jug by its handle to avoid it falling.
• When the blender is in use, do not use any other accessory than the pusher to avoid damaging the jug.
• Press on to turn off the screen.

CAUTION: After running one cycle in the blender for the maximum processing time, let the blender rest for 1 minute before you operate it again.

After using the blender for a maximum of two cycles, stop the appliance and leave to cool to ambient temperature (takes about 2 hours).

Overload protection

The appliance is equipped with overload protection. This prevents the motor from being damaged by overloading.

If the appliance switches off during operation, proceed as follows :

• Switch the appliance off using the power button, unplug and leave to cool down for approx.15-20 minutes.
• Reconnect the appliance to the power supply and resume blending.

3 programs :

Smoothie : The blender works at various speeds alternating for approx. 1 minute.

Hot soup : rehears and blends pre-cooked vegetables and broth thanks to the speed of blades.

Sorbet : The blender works at speed 6 for approx. 1 minute.

- The pulse button can still be used when no program is running.

RECIPES:

• Carrot soup : 800g pre-cooked carrots and 1,2L water for 3 min.
• Smoothie : 250g green apple with skin + 150g celery + 125g kiwi + 180g pear + 40g spinach + 225ml water +50g ice cube.
• Hot soup : 450ml chicken stock + 120g double cream +300g courgette + 100g carrots + 50g celery + 30g green pepper. vegetables have to be pre-cooked.
• Sorbet (Strawberry Ice): :450g frozen strawberries + 240ml milk + 130g caster sugar. Chill in the freezer until firm.

CAUTION: Hard foods may mark the inside of the jug but this does not affect the efficiency of the appliance.

Frozen foods must be smaller than a walnut.

Do not add hot liquid above 80° C as it can be ejected out of the appliance due to a sudden build up of steam.

AFTER USING YOUR APPLIANCE

• Press on the power button and unplug the appliance.
• Empty the preparation, the jug is not meant for storing food in the refrigerator or freezer.
• To clean the motor unit, use a damp cloth. Dry it carefully.
• Never immerse the motor unit in water.
• For easy cleaning, wash the removable parts in water with few drops of washing-up liquid, immediately after use.
• The jug, lid and measuring cap can be cleaned in the dishwasher, but the gasket must not go in the dishwasher.
• Frequent cleaning in a dishwasher risks damaging the surface of the jug.
• For easy cleaning, you can use the “Clean program”:
  Put 150ml of water and 1 drop washing up liquid in the jug. The blender works at various alternating speeds for approx. 1 min 30.

WHAT TO DO IF YOUR APPLIANCE DOES NOT WORK?

Problems Causes	Solutions
Appliance does not work	The plug is not connected.	Connect the appliance to a socket with the same voltage as indicated on the rating plate of the appliance.
	The blender jug is not positioned correctly on the motor unit.	Check that the blender jug is positioned properly on the motor unit as explained in the instructions.
	The power switch is on OFF position.	Follow the instructions for starting your appliance.
	In case of software bug.	Unplug the appliance, wait few minutes and plug in again.
The appliance stopped while in use	Overload	Follow the instructions in section Overload.
	The silicon gasket is missing or not correctly positioned.	Place the silicone gasket correctly on the motor unit.
Excessive vibrations	The product is not placed on a flat surface.	Place the appliance on a flat surface.
	Volume of ingredients is too high.	Reduce the quantity of ingredients processed.
	The silicon gasket is missing or not correctly positioned.	Place the silicone gasket correctly on the motor unit.
Leak from the lid	Volume of ingredients is too high.	Reduce the quantity of ingredients processed.
	The lid is not correctly positioned	Place the lid correctly on the blender jug.
Leak from the bottom of the blender jug	Deterioration of the watertightness of the appliance	Caution : the blades are not removable.Contact the consumer service, see contact information in the warranty leaflet.
The blades do not turn easily	Pieces of food too large or too hard.	Reduce the size or quantity of ingredients processed.
	The blended liquid is too hot and distorted the silicone gasket.	Replace the gasket with a new one.

ОПИСАНИЕ НА УРЕДА

BESCHRIJVING VAN HET APPARAAT

1. Vulstop
2. Deksel
3. Kan
4. Afneembare siliconen pakking
5. Motorblok
6. Stamper
7. Aan-uitknop

WERKEN MET HET APPARAAT

NA HET WERKEN MET HET APPARAAT

WAT TE DOEN ALS JOUW APPARAAT NIET GOED WERKT?