Axxess AX-ADCH02 - Car electronic accessory Metra - Free user manual and instructions

Product Type	Antenna Interface Adapter
Model	Axxess AX-ADCH02
Brand	Metra
Dimensions (L x W x H)	2.5 x 1.5 x 0.5 inches
Weight	0.1 lbs
Power Input	12V DC (vehicle power)
Connector Type - Input	OEM Antenna Connector
Connector Type - Output	Standard Motorola Antenna Connector
Compatible Vehicles	Select Chrysler, Dodge, Jeep, and Mitsubishi models
Material	Plastic with metal contacts
Color	Black
Installation Method	Plug-and-play, no wiring required
Primary Function	Converts OEM antenna connector to aftermarket radio connector
Maintenance	Wipe with dry cloth; avoid liquids
Storage Temperature	-20°C to 70°C
Certification	CE, RoHS compliant

Frequently Asked Questions - Axxess AX-ADCH02 Metra

What is the Metra Axxess AX-ADCH02 used for?

The Axxess AX-ADCH02 is an antenna adapter that allows you to connect an aftermarket radio to the factory antenna in compatible Chrysler, Dodge, Jeep, and Mitsubishi vehicles.

Which vehicles are compatible with the AX-ADCH02?

It is compatible with select Chrysler, Dodge, Jeep, and Mitsubishi models. Check the vehicle fitment guide on Metra's website for a complete list.

Does the AX-ADCH02 require any wiring or cutting?

No, it is a plug-and-play adapter. Simply connect the adapter between the vehicle's antenna cable and the aftermarket radio's antenna input.

Will the AX-ADCH02 work with all aftermarket radios?

It works with most aftermarket radios that have a standard Motorola-style antenna input. Some high-end radios may require a different adapter.

How do I install the AX-ADCH02?

First, disconnect the vehicle's negative battery terminal. Then, unplug the factory antenna connector from the factory radio, plug the AX-ADCH02 into the factory connector, and connect the other end to your aftermarket radio's antenna input.

What are the dimensions of the AX-ADCH02?

The adapter measures approximately 2.5 inches by 1.5 inches by 0.5 inches and weighs about 0.1 lbs.

Can I use this adapter for FM/AM radio?

Yes, it supports both FM and AM frequency bands without signal loss.

Is the AX-ADCH02 compatible with satellite radio?

No, it is designed specifically for terrestrial AM/FM antenna connections. Satellite radio requires a separate adapter.

What should I do if the radio does not receive any stations after installation?

Check that the adapter is fully seated on both connectors. Ensure the aftermarket radio's antenna input is compatible. Also verify that the vehicle's antenna is functioning properly.

How do I clean and maintain the AX-ADCH02?

Clean the adapter with a dry, lint-free cloth. Avoid exposure to moisture and extreme temperatures. No specific maintenance is required.

USER MANUAL Axxess AX-ADCH02 Metra

Close-up of various electronic components including a gray connector, black connectors, and a metallic connector (no visible text or symbols)

Chrysler Data Interface 2007-up\*

*Visit AxxessInterfaces.com for up-to-date vehicle specific applications.

INTRODUCTION

The AX-ADCH02 harness is designed for, and must be used with, the AX-ADBOX1 or AX-ADBOX2 interface (sold separately). Please refer to the AX-ADBOX1 or AX-ADBOX2 for the 16-pin connector with stripped leads

INTERFACE FEATURES

• Provides accessory power (12-volt 10-amp)
• Maintains the retained accessory power (R.A.P.) feature
• Provides NAV outputs (parking brake, reverse, speed sense)
• Retains safety chimes
  • Pre-wired ASWC-1 harness (ASWC-1 sold separately)

* To retain fade in amplified models, use the AX-ADBOX1

APPLICATIONS

See inside front cover

• Can be used in both amplified and non-amplified models
• Retains balance and fade ^†
• Retains Blind Spot Detection (if equipped)
• Micro "B" USB updatable

TABLE OF CONTENTS

Connections to be made

For models without an amplifier ....3

For models with an amplifier ....4

Installing & programming the AX-ADCH02

AX-ADBOX1 5

AX-ADBOX2 6

Adjusting the AX-ADCH02 7

INTERFACE COMPONENTS

• AX-ADCH02 harness
  • 4-pin harness with stripped leads

TOOLS REQUIRED

- Crimping tool and connectors, or solder gun, solder, and heat shrink • Small flat-blade screwdriver

- Tape • Wire cutter • Zip ties

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

APPLICATIONS

CHRYSLER

200 2011-2014

300 2008-2010

Aspen 2008-2009

Sebring 2007-2010

Town & Country 2008-2017

DODGE

Avenger 2008-2014
Caliber 2009-2010
Caravan/Grand Caravan 2008-up
Challenger 2009-2014
Charger 2008-2010
Dakota 2008-2011
Durango 2008-2013
Journey	2009-2010
Magnum	2008-2009
Nitro	2007-2011
Ram 1500	2009-2011
Ram 2500/3500	2010-2011

JEEP

Commander	2008-2010
Compass	2009-2017.5
Grand Cherokee 2008-2013
Liberty 2008-2012
Patriot	2009-2017
Wrangler 2007-2017
Wrangler(JK body type)	2018

MITSUBISHI

Raider	2008-2009
RAM
1500/2500/3500	2012
C/V Tradesman	2012-2015
VOLKSWAGEN
Routan	2009-2013

CONNECTIONS TO BE MADE

Attention! This interface will work with models that are either non-amplified, or amplified. Please follow the instructions carefully for your model vehicle. Failure to do so will result in either no sound, or low sound. If you are unsure if your vehicle is factory amplified or not, please contact your local dealership.

For models without an amplifier:

From the 16-pin harness with stripped leads to the aftermarket radio (harness included with interface):

- Connect the Red wire to the accessory wire.

Note: If installing an ASWC-1 (sold separately), connect the Red wire on the AX-ADCH02 harness as well.

• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.

Attention! The following (4) wires are reversed on purpose. These wires will not match “color code” to the aftermarket radio.

• Connect the Gray wire to the right rear positive speaker output.
• Connect the Gray/Black wire to the right rear negative speaker output.
• Connect the White wire to the left rear positive speaker output.
• Connect the White/Black wire to the left rear negative speaker output.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the Blue/Pink wire to the VSS/speed sense wire.
• Connect the Green/Purple wire to the reverse wire.
• Connect the Light Green wire to the parking brake wire
• Tape off and disregard the following (6) wires, they will not be used in this application:

Blue/White, Brown, Green, Green/Black, Purple, Purple/Black

From the AX-ADCH02 harness to the aftermarket radio:

• Connect the Black wire to the ground wire.
• Connect the Yellow wire to the battery wire.
• If installing an ASWC-1 (sold separately), connect the Red wire to accessory power.
• Connect the Blue/White wire to the power antenna wire.
• Ensure the (2) 4-pin Molex connectors (with green and purple wires) are connected together.
• Connect the 4-pin harness with stripped leads, to the 4-pin Molex connector (with gray and white wires).

Attention! The following (4) wires are reversed on purpose. These wires will not match “color code” to the aftermarket radio.

• Connect the Green wire to the right front positive speaker output.
• Connect the Green/Black wire to the right front negative speaker output.
• Connect the Purple wire to the left front positive speaker output.
• Connect the Purple/Black wire to the left front negative speaker output.

12-pin pre-wired ASWC-1 harness:

This harness is to be used along with the optional ASWC-1 (sold separately) to retain steering wheel audio controls. If the ASWC-1 is not being used, disregard this harness. If the ASWC-1 will be used, please refer to the ASWC-1 instructions for radio connections and programming. Disregard the harness that comes with the ASWC-1.

Continue to Installing & Programming the AX-ADCH02

CONNECTIONS TO BE MADE

Attention! This interface will work with models that are either non-amplified, or amplified. Please follow the instructions carefully for your model vehicle. Failure to do so will result in either no sound, or low sound. If you are unsure if your vehicle is factory amplified or not, please contact your local dealership

For models with an amplifier:

From the 16-pin harness with stripped leads to the aftermarket radio (harness included with interface):

• Connect the Red wire to the accessory wire.
  Note: If installing an ASWC-1 (sold separately), connect the Red wire on the AX-ADCH03 harness as well.
• Connect the Blue/White wire to the amp turn on wire. This wire must be connected to hear sound from the factory amplifier. There will also be a Blue wire on the AX-ADCH02 harness to connect as well.
• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.
• Connect the Gray wire to the right front positive speaker output.
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the White wire to the left front positive speaker output.
• Connect the White/Black wire to the left front negative speaker output.
• Connect the Green wire to the left rear positive speaker output.
• Connect the Green/Black wire to the left rear negative speaker output.
• Connect the Purple wire to the right rear positive speaker output.
• Connect the Purple/Black wire to the right rear negative output.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the Blue/Pink wire to the VSS/speed sense wire.
• Connect the Green/Purple wire to the reverse wire.
• Connect the Light Green wire to the parking brake wire
• Tape off and disregard the following (1) wire, it will not be used in this application: Brown

From the AX-ADCH02 harness to the aftermarket radio:

• Connect the Black wire to the ground wire.
• Connect the Yellow wire to the battery wire.
• If installing an ASWC-1 (sold separately), connect the Red wire to accessory power.
• Connect the Blue wire to the amp turn-on wire.
• Ensure the (2) 4-pin Molex connectors (with green and purple wires) are connected together.
• Disregard the 4-pin Molex connector (with gray and white wires), it will not be used in this application.
• Disregard the 4-pin harness with stripped leads, it will not be used in this application.

12-pin pre-wired ASWC-1 harness:

This harness is to be used along with the optional ASWC-1 (sold separately) to retain steering wheel audio controls. If the ASWC-1 is not being used, disregard this harness. If the ASWC-1 will be used, please refer to the ASWC-1 instructions for radio connections and programming. Disregard the harness that comes with the ASWC-1.

Continue to Installing & Programming the AX-ADCH02

INSTALLING & PROGRAMMING THE AX-ADCHO2

Attention! The AX-ADCH02 will work with both the AX-ADBOX1 and AX-ADBOX2 interfaces, but programming will be different. Refer to the proper page for whichever interface is being used. Also note, the programming instructions for the AX-ADBOX2 reflect gen. 2. If installing a gen. 1 AX-ADBOX2, refer to the AX-ADBOX1 programming instructions. Gen. 2 interfaces can be distinguished by a blue reset button between the (2) connectors.

AX-ADBOX1

Installing the AX-ADCH02

With the key in the off position:

• Connect the 16-pin harness with stripped leads, and the AX-ADCH02 harness, into the interface.
• Connect the AX-ADCH02 harness to the wiring harness in the vehicle.
• If an ASWC-1 (sold separately) will be used, do not connect it until the AX-ADCH02 is programmed and fully functional.

Programming the AX-ADCH02

Attention! If the interface ever loses power, the following steps will need to be performed again. Please ensure that the owner of the vehicle knows this.

- Turn the key (or push-to-start button) to the ignition position and wait until the radio comes on.

Note: If the radio doesn't not come on within 60 seconds, turn the key to the off position, disconnect the interface, check all connections, reconnect the interface, and then try again.

- Turn the key (or push-to-start button) to the off position, then to the accessory position. Test all functions of the installation for proper operation, before reassembling the dash.

Note: To use fade in amplified models, ensure the radio is turned up 3/4 of the way.

Continue to Adjusting the AX-ADCH02

INSTALLING & PROGRAMMING THE AX-ADCHO2

Attention! The AX-ADCH02 will work with both the AX-ADBOX1 and AX-ADBOX2 interfaces, but programming will be different. Refer to the proper page for whichever interface is being used. Also note, the programming instructions for the AX-ADBOX2 reflect gen. 2. If installing a gen. 1 AX-ADBOX2, refer to the AX-ADBOX1 programming instructions. Gen. 2 interfaces can be distinguished by a blue reset button between the (2) connectors.

AX-ADBOX2

Installing the AX-ADCH02

With the key in the off position:

• Connect the 16-pin harness with stripped leads, and the AX-ADCH02 harness, into the interface.
• If an ASWC-1 (sold separately) will be used, do not connect it until the AX-ADCH02 is programmed and fully functional.

Attention! Do not connect the AX-ADCH02 harness to the wiring harness in the vehicle just yet.

Programming the AX-ADCHO2

For the steps below, the L.E.D. located inside the interface can only be seen while active. The interface does not need to be opened to see the L.E.D.

1. Start the vehicle.

2. Connect the AX-ADCH02 harness to the wiring harness in the vehicle. The L.E.D. will initially be Green to indicate the interface is powered.

3. After a few seconds the L.E.D. will turn on solid Red while the interface automatically programs to the vehicle. The radio will shut off at this point. This process should take 5 to 30 seconds.

4. After the interface is programmed, the L.E.D. will turn on solid Green, and the radio will come back on, indicating programming was successful.
5. Test all functions of the installation for proper operation, before reassembling the dash.
6. If the interface fails to function, refer to "Troubleshooting", "Resetting the interface".

Troubleshooting

Resetting the interface

1. The Blue reset button is located inside the interface, between the two connectors. The button is accessible outside the interface, no need to open the interface.
2. Press and hold the reset button for two seconds, then let go to reset the interface.
3. Refer to "Programming the AX-ADCH02 Interface" from this point.

Continue to Adjusting the AX-ADCH02

ADJUSTING THE AX-ADCHO2

Audio level adjustment (amplified models only):

• With the vehicle and radio turned on, turn the volume up 3/4 of the way.
• With a small flat-blade screwdriver, adjust the potentiometer clockwise to raise the audio level; counterclockwise to lower the audio level.
• Once at a desired level, audio level adjustment is complete.

AX-ADCHO2 INSTALLATION INSTRUCTIONS

IMPORTANT

If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

Close-up of various electronic components including a multi-pin connector, power connector, and motor (no visible text or symbols)

CARACTERÍSTICAS DE LA INTERFAZ

- Turn the key to the off position, and then to the accessory position. Test all functions of the installation for proper operation, before reassembling the dash.