Q: How to remove the cutting deck from the Honda HF2625HME mower?

Before you begin: Make sure the engine is off, the transmission is in neutral, and the cutting blades are completely stopped. These precautions are essential for your safety. The cutting deck of your Honda HF2625HME mower (width 62 cm) is a component that you may need to access during maintenance, particularly for cleaning the blades or sharpening, operations recommended every 20-25 hours of use according to the manual. To remove the deck: Position the mower on a flat and stable surface Turn off the engine and remove the ignition key Check that the blades are no longer turning (wait a few seconds) Locate the deck attachment points under the machine - usually bolts or retaining pins Use an appropriate wrench or screwdriver depending on the type of attachment Carefully remove, ensuring that no part gets stuck The complete PDF of this manual (252 pages) contains detailed diagrams and the exact positions of the attachment points for this model. Refer to the

Question 1

What does the yellow icon displayed on the panel of my Honda HF2417HTE mower mean?

Accepted Answer

The flashing yellow icon on the panel indicates that the grass collection bag is full. When this light comes on, the mower also emits an intermittent sound signal to alert you.

To continue mowing, you need to:

Stop the engine by turning the ignition key to the "OFF" position
Empty the grass collection bag
Properly reattach the bag to ensure contact is made
Restart the mower

If the light remains on after emptying the bag, check that the bag is securely attached and that the fill sensor is not blocked by grass or debris.

Question 2

Why does the engine lose revolutions when I engage the blade?

Accepted Answer

When you engage the cutting blade on your Honda HF2417HTE, a drop in engine revolutions is perfectly normal and unavoidable. The Honda GCV530 4-stroke engine provides limited power (9.7 kW at 2800 rpm at nominal speed), and driving the cutting blade (width 92 cm) consumes a significant portion of this power. You will see the speed drop slightly and stabilize after a few seconds, which is the expected operation of your machine.

However, if the drop in revolutions is very significant or if the engine struggles to restart after engaging the blade, several points need to be checked:

Check the condition and sharpening of the blade - A dull, unbalanced, or damaged blade requires much more effort from the engine. Inspect both blades of the cutting assembly (width 92 cm) and have them sharpened or replaced by a specialist if necessary. Also, ensure they are well balanced.
Check the air and fuel filters - A clogged air filter limits air intake and reduces power. A blocked fuel filter restricts fuel supply. Clean or replace them according to the manual's recommendations. Old or poor-quality fuel can also cause performance issues.
Check the engine oil level - Your engine should contain exactly 1.1 liters of SAE 10W30 oil. An insufficient level significantly reduces performance and can damage the engine. Check the level on a flat surface with the dipstick and top up if necessary.
Check the tension of the drive belt - A loose or worn belt poorly transmits power from the engine to the blades. Check its condition and tension. A slipping belt can give the impression that the engine is losing speed when it is actually an inefficient transmission.
Clean the cooling system - A dirty engine (grass, debris) can overheat and lose performance. Ensure that the cooling fins are clean.
Adjust your forward speed to the height of the grass - Engaging the blade in very dense or very tall grass on the first cut requires much more power. Start by raising the cutting height (positions 5 to 7 out of 7) and move forward slowly. Gradually progress to lower cuts in subsequent passes.

If the problem persists after these checks, contact an authorized Honda dealer who will have the necessary equipment to diagnose internal engine faults.

Question 3

How to remove the cutting deck from the Honda HF2625HME mower?

Accepted Answer

Before you begin: Make sure the engine is off, the transmission is in neutral, and the cutting blades are completely stopped. These precautions are essential for your safety.

The cutting deck of your Honda HF2625HME mower (width 62 cm) is a component that you may need to access during maintenance, particularly for cleaning the blades or sharpening, operations recommended every 20-25 hours of use according to the manual.

To remove the deck:

Position the mower on a flat and stable surface
Turn off the engine and remove the ignition key
Check that the blades are no longer turning (wait a few seconds)
Locate the deck attachment points under the machine - usually bolts or retaining pins
Use an appropriate wrench or screwdriver depending on the type of attachment
Carefully remove, ensuring that no part gets stuck

The complete PDF of this manual (252 pages) contains detailed diagrams and the exact positions of the attachment points for this model. Refer to the

Question 4

The Honda HF2317HME mower won't start - what should I check?

Accepted Answer

Before attempting to start, first check that your Honda HF2317HME meets all safety criteria. The electronic safety system prevents the engine from starting if any of the conditions are not met: the transmission must be in neutral (N), the cutting blades must be disabled (magnetic clutch lever in neutral position), and you must be securely seated on the seat. Also, check that the parking brake lever is engaged.

Next, check the condition of the fuel and oil. The tank must contain unleaded gasoline (minimum Euro 95) - capacity 1.0 liter. Never fill the tank in a populated area or with the engine hot. Also check the engine oil level (SAE 10W-30) - insufficient oil will prevent starting. The battery must be fully charged before any attempt to start.

Correct starting procedure. First, turn the key to the “ON” position to activate the electrical circuit. For a cold start, operate the choke lever (starter) which enriches the fuel-air mixture - this is only useful for the first starts of a cold machine. If the engine is already warm, simply position the throttle (gas lever) between “SLOW” and “FAST”. Then, turn the key to the “START” position and release it as soon as the engine starts - it will automatically return to “ON”.

If the starter does not turn. This usually indicates a poorly charged battery or unmet safety conditions. Check that the control panel is lit (no safety cut-off). If the transmission is not in neutral or if you have stood up from the seat during the attempt, the safety cuts off the engine. If you have used the “Cruise Control” since a previous start, you must disconnect it - the neutral indicator (N) must be displayed on the panel.

If the starter turns but the engine does not start. First, check that the fuel is flowing properly: check the fuel filter (reference 6.4.4 of the manual). Inspect the spark plug - the cap must be tightly secured and the electrodes clean with the correct gap. If you haven't used the mower for a long time, the fuel may be contaminated: empty the tank and refill it with fresh gasoline. You can also clean the float chamber of the carburetor.

If starting is very difficult or the engine runs unevenly. A clogged air filter reduces air intake and prevents a good fuel mixture. Clean or replace the air filter (reference 6.4.3). Old fuel or bad gasoline can also cause misfires. Completely empty the tank and refill it with fresh unleaded gasoline.

Be cautious about starting conditions. All starts must be done outdoors or in a well-ventilated area - carbon monoxide is toxic. Wait at least 3 meters from where you refueled before starting. If you have spilled fuel on your clothes, change them before starting the engine. After starting, do not direct the exhaust towards flammable materials.

Question 5

How to correctly enter the PIN code on the Miimo HRM 70 Live?

Accepted Answer

The Miimo HRM 70 Live uses a four-digit PIN code. If you can only enter the first digit, the issue is usually related to the timing of entry or the navigation method.

Correct procedure:

Use the up/down buttons to navigate to the desired first digit
Press the confirmation button to validate this digit
Wait one second before entering the next digit
Repeat this process for the remaining three digits

Important points:

The mower automatically locks after 3 minutes of inactivity. If the buttons are unresponsive, you will need to start entering the PIN again
Ensure that the on/off switch is activated before entering the code
If the problem persists, check that all four navigation buttons are responding correctly - a faulty button would prevent the entry of subsequent digits

If the problem continues, contact an authorized Honda dealer for repair.

Question 6

What are the recommended service intervals for the Honda Miimo HRM 70 Live?

Accepted Answer

Honda recommends that annual maintenance be performed by your local authorized Honda dealer. There is no detailed schedule with specific operating hours in the manual for this mower.

Regular maintenance tasks

Blade inspection - Regularly check that the blades, blade bolts, and the entire cutting device are not worn or damaged
Tightening fasteners - Ensure that all nuts, bolts, and screws are tight
Cleaning - Carefully clean the exterior of the machine with a soft brush and cloth

Important points: The blades are reversible, and the lithium-ion battery (approximately 60 minutes of runtime) is a wear part to monitor. This manual does not provide a specific parts replacement schedule, so contact your Honda dealer for a personalized diagnosis if you notice a drop in performance.

Question 7

Why is the grass no longer going into the collection bag of my Honda HF2417HTE mower?

Accepted Answer

If the grass is no longer directed into the collection bag of your Honda HF2417HTE mower, several causes may be behind this issue. Here are the points to check to resolve this situation:

1. Check the collection bag

Make sure the bag is not full. A saturated bag prevents grass from accumulating properly.
Ensure that the bag is securely attached and positioned according to the manufacturer's instructions to ensure proper airflow.

2. Check the collection duct

Inspect the duct connecting the mower to the bag for any blockages caused by clumps of grass or debris.
Carefully clean this passage if necessary to restore free flow.

3. Adjust the cutting height

A cutting height that is too low can cause an accumulation of cut grass that blocks the passage to the bag.
Try slightly increasing the cutting height to facilitate collection.

4. Condition of the blades

Dull or damaged blades do not cut grass effectively, which can hinder its transport to the bag.
Check the condition of the blades and sharpen or replace them if necessary.

By following these steps, you should be able to identify and correct the cause preventing the grass from going into the collection bag. If the problem persists, it may be helpful to have your mower checked by a professional.

User manual Honda : user manuals and guides in PDF

Models Honda most viewed

Browse manuals Honda by appliance type

Recent questions about devices Honda