Q: What do the cycles mean in the operation of the FLECK 4600 motorized valve?

In a FLECK 4600 motorized valve, the cycles correspond to the different operating phases that ensure optimal water treatment, particularly during the regeneration process of the softening resin. Main cycles of the FLECK 4600 valve: Service cycle: This is the normal phase where hard water passes through the resin, which retains the minerals responsible for hardness (calcium, magnesium). The treated water is softened and ready for use. Regeneration cycle: This phase is triggered when the resin is saturated with minerals. It includes several steps: Backwash: removal of accumulated impurities on the resin. Saturation: introduction of a saline solution (saltwater) to recharge the resin with sodium ions. Final rinse: removal of excess salt and residues to prepare the resin for a new service cycle. Filling cycle: On some models, this cycle allows the salt tank to be filled with water to prepare the saline solution used during regeneration. Each cycle has a specific duration and order, programmed into the valve according to water consumption and detected hardness. These cycles ensure optimal efficiency and automatic operation of the softener.

Question 1

How to use the FLECK 5600 water softener?

Accepted Answer

The FLECK 5600 water softener is designed to reduce water hardness in your home installation. Here’s how to use it effectively:

1. Installation

Ensure that the softener is correctly installed on the main water supply line. Professional installation is recommended to ensure optimal operation.

2. Start-up and initial settings

Turn on the device.
Set the local water hardness on the control panel, according to the results of a water hardness test.
Adjust the time and frequency of automatic regeneration if necessary.

3. Regeneration

The softener automatically performs a regeneration cycle to recharge the resin with sodium ions. Check that the salt tank is always filled to ensure this process.

4. Maintenance and monitoring

Regularly check the salt level and add more if needed.
Monitor the proper functioning of the cycles and the quality of the softened water.
Perform periodic maintenance, including cleaning the filters if your model is equipped with them.

By following these steps, your FLECK 5600 softener will operate efficiently to protect your installations and improve the quality of your water.

Question 2

What does the red regeneration light on the FLECK 4600 motorized valve mean and how can I resolve this issue?

Accepted Answer

The red regeneration light on the FLECK 4600 motorized valve simply indicates that your water softener is in the process of regeneration. This is a normal and expected operation of the valve. Regeneration is the automatic process during which the softener cleans its resin to continue treating water effectively. This cycle lasts about 180 minutes (3 hours) for a standard regeneration, or 90 minutes if you have the Fast Regen option.

The red light only becomes a problem if it indicates a regeneration that never stops or that occurs too frequently. In these cases, check the following points:

Insufficient salt level: Check that the salt tank contains salt above the water level. The level must remain above the water. A lack of salt prevents regeneration from functioning properly and can lock the valve in regeneration mode.
Brine tank: The water level in the tank should not be excessive. Check that the automatic filling is working correctly and is not overfilling the tank (a problem that causes continuous regeneration).
Programming: Ensure that the regeneration cycle is correctly programmed. For the timer version, check the interval in days and the scheduled regeneration time. For the volumetric version, make sure the set capacity (in m³) matches your water consumption.
Unplug and wait: If the red light stays on continuously, turn off the device for 10 minutes, then turn it back on. If the valve returns to service mode (green light), the cycle is complete. If the red persists, it indicates a failure of the motor or control head.

If after these checks the red light continues to illuminate abnormally or never turns off, it may be necessary to replace the control head or call a professional to diagnose a potential motor fault.

Question 3

How to manually perform a regeneration on a FLECK 4600 motorized valve?

Accepted Answer

Yes, it is possible to manually perform a regeneration on a FLECK 4600 motorized valve. Here’s how to proceed:

Steps to initiate a manual regeneration

Access the valve: Open the valve cover to access the control panel.
Locate the regeneration button: On the panel, find the button or switch dedicated to regeneration. It may be labeled "Regeneration", "Regenerate" or have a specific symbol.
Trigger the regeneration: Press this button to start the regeneration cycle. The valve will then automatically begin the different phases, including rinsing and saturation.
Monitoring: During the process, it is advisable to monitor the valve to ensure that the regeneration is proceeding correctly. This cycle may last several minutes.
End of cycle: Once the regeneration is complete, the valve will automatically return to service mode.
Close the valve: Don’t forget to close the cover to protect the controls.

This procedure allows you to manually restart the regeneration of your water softening or filtration system equipped with a FLECK 4600 valve, which can be useful in case of specific needs or maintenance.

Question 4

What do the cycles mean in the operation of the FLECK 4600 motorized valve?

Accepted Answer

In a FLECK 4600 motorized valve, the cycles correspond to the different operating phases that ensure optimal water treatment, particularly during the regeneration process of the softening resin.

Main cycles of the FLECK 4600 valve:

Service cycle: This is the normal phase where hard water passes through the resin, which retains the minerals responsible for hardness (calcium, magnesium). The treated water is softened and ready for use.
Regeneration cycle: This phase is triggered when the resin is saturated with minerals. It includes several steps:
- Backwash: removal of accumulated impurities on the resin.
- Saturation: introduction of a saline solution (saltwater) to recharge the resin with sodium ions.
- Final rinse: removal of excess salt and residues to prepare the resin for a new service cycle.
Filling cycle: On some models, this cycle allows the salt tank to be filled with water to prepare the saline solution used during regeneration.

Each cycle has a specific duration and order, programmed into the valve according to water consumption and detected hardness. These cycles ensure optimal efficiency and automatic operation of the softener.

Question 5

How to clean the resin in a FLECK 4600 motorized valve?

Accepted Answer

Cleaning the resin in a FLECK 4600 motorized valve is an important operation to maintain the efficiency of the water treatment system. Here are the steps to follow:

1. Preparation

Turn off the water and electricity supply to the valve to ensure your safety during the intervention.
Locate and remove the valve cover to access the resin tank.

2. Resin Inspection

Examine the resin: if it is dirty, clumped, or discolored, cleaning is necessary.
If the resin is too worn or contaminated, it may be better to replace it.

3. Cleaning the Resin

Use a specific cleaning product for resin, available commercially, suitable for water softeners.
Follow the manufacturer's instructions for dosage and application method.
Pour the product into the resin tank according to the recommendations.

4. Rinsing

Start a complete rinsing cycle to remove any residue of the cleaning product.
Ensure that the rinsing water is clear and free of chemical odor.

5. Reassembly and Verification

Replace the valve cover properly.
Restore the water and electricity supply.
Test the operation of the valve to ensure everything is in order.

Regular maintenance of the resin ensures better performance of your FLECK 4600 motorized valve and extends its lifespan.

Question 6

How to set the time on a FLECK 4600 water softener?

Accepted Answer

To set the time on your FLECK 4600 water softener, you need to access the 24-hour wheel on the control panel of the control head, located on top of the unit. This operation takes only a few seconds and requires no tools.

Setting Steps:

Locate the 24-hour wheel clutch (the red gear) on the control panel
Press firmly on this clutch to activate it
While holding the clutch down, turn the hour wheel to display the correct time in the small window provided for this purpose
Release the clutch once the time is set correctly

The time is displayed on a small display located under the 24-hour wheel. Make sure to set the exact time for day and night (24-hour format). This setting is particularly important as it determines when the valve will perform the programmed regeneration cycles, usually in timer mode.

The control panel of the FLECK 4600 has a green light that indicates the unit is in service position, and a red light that turns on during regeneration. If your unit has a volumetric version rather than a timer version, the 24-hour wheel also plays a role in the overall operation of the system. The time setting should be checked regularly, especially after a prolonged power outage.

User manual FLECK : user manuals and guides in PDF

Models FLECK most viewed

Browse manuals FLECK by appliance type

Recent questions about devices FLECK