Question 1

How to clean the pot sensor of the NINJA Foodi MAX OL750EU?

Accepted Answer

The pot sensor of the NINJA Foodi MAX OL750EU is located at the center of the cooking plate, at the base of the appliance. Here’s how to clean it properly:

Cleaning Steps

Check for obstruction: Inspect the sensor to see if there are any food residues or debris blocking it.
Clean with a damp cloth: Use a soft, damp cloth to clean the area around the sensor. Make sure the sensor itself is free from any obstruction.
Remove and reinsert the pot: Once cleaning is complete, remove and then reinsert the pot into the appliance to reset the sensor detection.

Important Points

The sensor must move freely up and down (it has a spring movement). If it remains stuck or if there is still a POT ERROR after cleaning, check that nothing is obstructing its movement. A clean and mobile sensor is essential for the appliance to function properly.

Question 2

How to use the Woodfire smoking function in grill mode?

Accepted Answer

Preparing the Woodfire smoker: To use the smoking function in grill mode on your Woodfire OG701EU, start by lifting the lid of the removable smoke box (located on the right side of the lid). Using the provided scoop, fill the smoke box completely with Ninja wood pellets to the top, then close the lid. Do not exceed the top to avoid introducing oxygen. Ensure that the grill is plugged in and that the grease tray is properly installed at the back.

Selecting Grill Mode: Turn the selection knob clockwise from the OFF position to select the GRILL function. Then, press the WOODFIRE FLAVOUR technology button to activate the smoking function. The pellets will go through an automatic ignition cycle (IGN) followed by preheating (PRE).

Setting the Temperature and Time: The default temperature setting will be displayed on the screen. Use the +/- buttons next to TEMP to adjust the temperature from LO (low) to HI (high). Then use the +/- buttons next to TIME to set the cooking time in 1-minute increments, up to a maximum of 1 hour.

Starting Cooking: Press the START button to begin preheating. During preheating with Woodfire, the pellets will first go through the ignition cycle (IGN - visible on the screen), then the grill enters the preheating phase (PRE). The preheating time varies by temperature: about 8 to 12 minutes on HI mode, 6 to 11 minutes on MED mode, and 5 to 9 minutes on LO mode. Preheating is highly recommended for best results. If you want to start immediately, you can skip preheating by pressing and holding the START/STOP button for 4 seconds.

Adding Food: When preheating is complete, the grill beeps and "ADD FOOD" appears on the screen. Open the lid and place your food on the cooking grate. Once the lid is closed, cooking begins and the timer starts counting down. When cooking is complete (the timer reaches zero), the grill beeps and "DONE" appears on the screen.

Important - Using Pellets: Always use genuine Ninja wood pellets for the best smoking flavors. Never fill the smoke box with heating pellets, hardwood, charcoal, or other fuels. Ninja has perfected the amount of pellets for each session, regardless of food size. Always fill the box to the maximum - it will automatically burn the appropriate amounts. After cooking, do not lift the lid or the smoke box until the grill has completely stopped smoking and the pellets are fully burned.

If you wish to extend smoking by adding more pellets during cooking, wait until the first batch is completely burned, then press and hold the WOODFIRE FLAVOUR technology button for 4 seconds to restart the ignition of a new full box. Do this operation only once or twice maximum. Never use oils or non-stick sprays during smoking, as the smoke will not adhere as well to the food.

Question 3

How to use the Ninja Creami NC300EU ice cream maker?

Accepted Answer

To use the Ninja Creami NC300EU ice cream maker, follow these steps:

1. Preparing the ice base

Prepare the mixture you want to turn into ice cream, sorbet, or other frozen dessert. You can use ingredients like fruits, milk, cream, sugar, depending on the chosen recipe.

2. Filling the container

Pour the preparation into the designated container, making sure not to exceed the fill line indicated to ensure proper functioning.

3. Freezing

Place the closed container in your freezer for at least 24 hours. This step is essential for the preparation to be well frozen before processing.

4. Installing in the machine

After freezing, remove the container from the freezer and install it in the Ninja Creami NC300EU machine.

5. Selecting the program

Turn on the machine and choose the program suitable for the type of preparation (ice cream, sorbet, frozen milk, etc.).

6. Starting the process

The machine will then mix and aerate the preparation to achieve a creamy texture. This process lasts a few minutes.

7. Serving

Once the cycle is complete, remove the container and serve your ice cream immediately. You can also store the dessert in the freezer for later consumption.

8. Cleaning

After use, carefully clean the container and accessories to ensure good hygiene and prolong the lifespan of your appliance.

Question 4

What commercial products are recommended for descaling the Ninja CP307 coffee machine?

Accepted Answer

To descale your Ninja CP307, two commercial solutions are recommended:

Specific descaling solution: Use a descaling solution specifically designed for coffee machines. Always follow the manufacturer's instructions for the product. These solutions are formulated to effectively remove limescale without damaging the internal components of your machine.
Alternative with white vinegar: You can also use pure white vinegar. Pour 0.47 liters (16 oz) of white vinegar into the reservoir, then fill with fresh water up to the maximum fill line (1.48 liters / 50 oz). Important: only use white vinegar.

Step-by-step descaling procedure:

Select the Full Carafe setting and place an empty carafe under the brew basket.
Pour your descaling solution (or the vinegar-water mixture) into the water reservoir up to the maximum fill line.
Press the CLEAN button. An automatic cleaning cycle will start, lasting about 60 minutes.
IMPORTANT: Do not remove the carafe during the entire cleaning cycle. The machine will dispense the solution, pause for maximum cleaning, and then add more solution.
At the end of the cycle, the device will beep, the clock will display "End", and the CLEAN indicator will turn off.

After descaling:

Empty and thoroughly clean the carafe and water reservoir with hot soapy water to remove any residue from the solution.
Fill the water reservoir with fresh water up to the maximum fill line.
Run a full rinse cycle: select Full Carafe and Classic Brew with water only. At the end, discard the water and clean the carafe again.
The CLEAN indicator will automatically light up when descaling is recommended again (usually based on the hardness of your water and frequency of use).

Important tip: Do not cancel the cleaning cycle midway, otherwise your machine will not be properly descaled. Limescale buildup can affect the flavor of your coffee or tea.

User manual NINJA : user manuals and guides in PDF

Models NINJA most viewed

Browse manuals NINJA by appliance type

Recent questions about devices NINJA