Q: The dishwasher does not start and no indicator lights appear

Symptom: The BAUMATIC BI 3F53L0B-80 dishwasher does not respond to the Start button, and no lights illuminate. Troubleshooting Procedure Before contacting technical support, check the following points: Check the power supply - Although you have confirmed that the outlet works with other devices, ensure that the dishwasher's cable is properly and fully inserted into the outlet. Use a direct wall outlet - Never plug the dishwasher into an extension cord or adapter. Direct connection to a properly grounded wall outlet is mandatory. Check that your outlet supports the required voltage: 220-240V, 50 Hz . Close the door properly - If the door is not closed or locked properly, the dishwasher cannot start for safety reasons. Push firmly until you hear a click. Test the START button again - Press firmly and hold the button for a few seconds. Some models require prolonged pressure. Check the house circuit breaker - If no lights appear, the power to the dishwasher is cut off. Check your electrical panel: the breaker dedicated to this appliance may not have been reset after a power outage. If after these checks no lights still appear, there is likely an internal electrical problem with the dishwasher (internal wiring fault, damaged power plug, or failure of the control unit). Contact an authorized BAUMATIC technical support center for professional repair.

Q: What is the width of the BAUMATIC P639BS oven?

The BAUMATIC P639BS oven has a width of 595 mm (which is 59.5 cm). This is a standard width for a built-in oven, compatible with most kitchen spaces designed for integrated cooking appliances.

Q: What are buttons 7 and 8 for on the BAUMATIC P629SS-ANZ oven?

Button 7 is the duration function (Duration). You press it to set how long the oven should cook. Once this time has elapsed, the oven will automatically turn off. Button 8 is the programmed stop function (End Cook). You press it to set the exact time you want the oven to stop cooking, rather than just setting a duration. When to use them: Use button 7 when you know the exact cooking time needed (e.g., 45 minutes) Use button 8 when you want the cooking to stop at a specific time (e.g., 7:30 PM) These two modes allow you to program the automatic stop of the oven, useful if you want the cooking to finish precisely at a certain time without manual supervision.

Q: What does error code E2 mean on my BAUMATIC BBT3518EWK refrigerator?

The error code E2 is not documented in the official manual of your BAUMATIC BBT3518EWK refrigerator. Your manual only mentions two types of errors identifiable by the indicators: Communication error: the temperature lights (-16°C to -24°C) light up one after the other Fan error: the temperature lights (-16°C, -20°C, -22°C, -24°C) flash simultaneously If your appliance displays E2, it may be a specific anomaly related to your model or a software variant that is not covered in the documentation. We recommend contacting BAUMATIC technical service mentioning your model BBT3518EWK and describing the symptoms precisely (lights on, shutdown mode, etc.).

Question 1

The dishwasher does not start and no indicator lights appear

Accepted Answer

Symptom: The BAUMATIC BI 3F53L0B-80 dishwasher does not respond to the Start button, and no lights illuminate.

Troubleshooting Procedure

Before contacting technical support, check the following points:

Check the power supply - Although you have confirmed that the outlet works with other devices, ensure that the dishwasher's cable is properly and fully inserted into the outlet.
Use a direct wall outlet - Never plug the dishwasher into an extension cord or adapter. Direct connection to a properly grounded wall outlet is mandatory. Check that your outlet supports the required voltage: 220-240V, 50 Hz.
Close the door properly - If the door is not closed or locked properly, the dishwasher cannot start for safety reasons. Push firmly until you hear a click.
Test the START button again - Press firmly and hold the button for a few seconds. Some models require prolonged pressure.
Check the house circuit breaker - If no lights appear, the power to the dishwasher is cut off. Check your electrical panel: the breaker dedicated to this appliance may not have been reset after a power outage.

If after these checks no lights still appear, there is likely an internal electrical problem with the dishwasher (internal wiring fault, damaged power plug, or failure of the control unit). Contact an authorized BAUMATIC technical support center for professional repair.

Question 2

How to fix an oven that does not heat on BAUMATIC B904.1SS

Accepted Answer

Troubleshooting the oven that does not heat

If the main oven of your BAUMATIC B904.1SS is not heating, here are the checks to perform:

Initial steps

Check that the oven is in manual operation mode (press the manual mode button)
Confirm that you have selected both a cooking function AND a temperature
Ensure that the appliance is powered and that the main fuses are not tripped

If the grill works but not the oven

Check that the correct cooking function has been selected. The main oven and the grill would use separate heating elements.

Thermal overheating issue

If the heating element stops during use, this may indicate an activated thermal protection. Allow the appliance to cool down for about 2 hours, then try again.

If the problem persists

Unplug the appliance from the power supply and contact BAUMATIC customer service for technical assistance.

Question 3

What should I do if the oven of the BAUMATIC BO612BL cooker has stopped working?

Accepted Answer

If the oven is not working while the fuse, socket, and cooking plates are fine, here are the checks to perform:

Checks to do first

Select a cooking function - Make sure you have selected a function (fan oven, grill, etc.) and set the temperature on the thermostat. Simply plugging in the cooker does not activate the oven.
Let the oven cool for 2 hours - The heating element may have triggered a thermal protection system. Allow the appliance to cool completely before trying again.

If the problem persists

According to the BAUMATIC BO612BL manual, if the oven still does not work after these checks, turn off the appliance and unplug it from the power supply. The problem is likely due to a faulty thermostat, a damaged heating element, or another internal failure that requires professional repair.

Contact Baumatic customer service to request technical assistance rather than attempting a DIY repair.

Question 4

What is the width of the BAUMATIC P639BS oven?

Accepted Answer

The BAUMATIC P639BS oven has a width of 595 mm (which is 59.5 cm). This is a standard width for a built-in oven, compatible with most kitchen spaces designed for integrated cooking appliances.

Question 5

What are buttons 7 and 8 for on the BAUMATIC P629SS-ANZ oven?

Accepted Answer

Button 7 is the duration function (Duration). You press it to set how long the oven should cook. Once this time has elapsed, the oven will automatically turn off.

Button 8 is the programmed stop function (End Cook). You press it to set the exact time you want the oven to stop cooking, rather than just setting a duration.

When to use them:

Use button 7 when you know the exact cooking time needed (e.g., 45 minutes)
Use button 8 when you want the cooking to stop at a specific time (e.g., 7:30 PM)

These two modes allow you to program the automatic stop of the oven, useful if you want the cooking to finish precisely at a certain time without manual supervision.

Question 6

What are the other operating modes available if I do not use manual mode?

Accepted Answer

Your BAUMATIC P629SS-ANZ oven has several alternative operating modes to manual mode:

Duration Function - The oven cooks for the duration you set, then automatically stops at the end of the allotted time.
Stop Function - You set a specific stop time on the oven clock, which automatically turns off at that time.
Start and End Function - You set the desired cooking duration and stop time; the oven automatically calculates the start time to finish at your scheduled time.
Timer - A simple countdown alarm (does not control cooking).

To use one of these functions, first select the type of cooking (fan heat, grill, etc.), set the temperature, and then activate the time function of your choice instead of manual mode.

Question 7

How do I turn on the BAUMATIC P629SS-ANZ oven?

Accepted Answer

To turn on your BAUMATIC P629SS-ANZ oven, it is not enough to just turn the knobs - you must follow this procedure:

First, press the manual operation button (button 9) on the control panel - this step is essential to activate the oven.
Turn the function selection knob to choose your cooking mode (conventional heating, grill, fan, etc.).
Turn the thermostat knob to set the desired temperature (50-250°C).
Wait for the oven heating indicator to light up - it will turn off once the oven has reached the set temperature.

Also, make sure that your oven is properly connected to the electrical network (220-240V, 50Hz). If after pressing button 9 the oven still does not turn on, check the power supply and the circuit breaker.

Question 8

How to deactivate the child safety lock on my BAUMATIC BOS243X oven?

Accepted Answer

To deactivate the child safety lock on your BAUMATIC BOS243X oven, press and hold the Set (+) button for at least 5 seconds.

Once this action is completed, the child safety lock will be deactivated and all oven functions will become accessible and selectable again.

Question 9

What does error code E2 mean on my BAUMATIC BBT3518EWK refrigerator?

Accepted Answer

The error code E2 is not documented in the official manual of your BAUMATIC BBT3518EWK refrigerator.

Your manual only mentions two types of errors identifiable by the indicators:

Communication error: the temperature lights (-16°C to -24°C) light up one after the other
Fan error: the temperature lights (-16°C, -20°C, -22°C, -24°C) flash simultaneously

If your appliance displays E2, it may be a specific anomaly related to your model or a software variant that is not covered in the documentation. We recommend contacting BAUMATIC technical service mentioning your model BBT3518EWK and describing the symptoms precisely (lights on, shutdown mode, etc.).

User manual BAUMATIC : user manuals and guides in PDF

Models BAUMATIC most viewed

Browse manuals BAUMATIC by appliance type

Recent questions about devices BAUMATIC