Question 1

Can the heart rate monitor be connected to the VirtuFit HTR 2.0?

Accepted Answer

No, the VirtuFit HTR 2.0 is not compatible with an external heart rate monitor. This device exclusively features pulse sensors integrated into the handlebars to measure your heart rate without any additional accessories.

How to use the pulse sensors:

Firmly hold both handlebars with both hands simultaneously
Maintain constant contact by applying light but steady pressure
For optimal measurement, your hands should be slightly damp
Your heart rate will be displayed in the PULSE section on the console's LCD screen

Important limitation: Never combine the built-in manual sensors with a wireless heart rate monitor or an external Bluetooth heart rate monitoring device. Using them simultaneously may cause interference and render both systems non-functional.

The manual sensors of the HTR 2.0 are sufficient to ensure reliable tracking of your heart rate during your cardio workouts.

Question 2

How to install and connect the pedals of the VirtuFit XB100i?

Accepted Answer

Installing the pedals of the VirtuFit XB100i is an essential step that must be done correctly to ensure your safety and the proper functioning of the bike. The pedals are numbered 29R (right) and 29L (left).

Direction for screwing the pedals:

Right pedal (R): screws in a clockwise direction on the crank
Left pedal (L): screws in a counterclockwise direction on the crank

This crossed orientation is intentional and prevents the pedals from loosening naturally during pedaling.

Installation steps:

Start by hand-screwing each pedal following the correct rotation direction according to its side (R or L)
Ensure that the threading engages correctly without forcing
Once the pedals are well engaged, tighten them securely using an appropriate wrench (refer to the provided tools)
Check that both pedals are firmly attached and do not move

Checking and maintenance:

After a few training sessions, check that the pedals remain tight, as they may loosen slightly with vibrations
If you hear a ticking noise while pedaling, it usually indicates that a pedal is loosening: completely disassemble it and reinstall it, ensuring the correct rotation direction before tightening it securely
A biannual check of all bolts and nuts is recommended, especially those related to the pedals and crank

The pedals of the VirtuFit XB100i do not require electronic connection: they are purely mechanical components. Proper installation and regular tightening ensure safe and comfortable use of your indoor bike.

Question 3

Where is the pedal sensor cable of the VirtuFit XB100i located?

Accepted Answer

The pedal sensor cable of the VirtuFit XB100i connects the sensor located at the crankset to the main display console of the device.

Cable Location

Starting Point: The sensor is located near the crankset, usually secured with a sensor mount.
Path: The cable runs along the main frame of the device to the console.
Ending Point: The cable connects to the back or side of the display console.

Checking and Troubleshooting

According to the manual, regularly check that:

The cable is properly connected on both ends (sensor and console) - no accidental disconnection.
The cable is not damaged, twisted, or pinched.
The connection is tight and does not move during use.

If you do not detail the sensor cable, refer to the assembly steps (01-03) in the manual provided with your device for accurate diagrams of the cable routing.

Question 4

Why doesn't the distance decrease when I have set a goal?

Accepted Answer

The distance counter must count down

On the XB100i, when you set a distance goal via the DISTANCE mode, the console must display this value and count it down to 0 as you ride.

If the distance does not decrease:

Check that you are in DISTANCE mode (press MODE to select this function)
Make sure the device is detecting your movements - pedal regularly for a few seconds after starting the session
Check that the AAA batteries (1.5 V) are properly installed and not depleted
Reset the console with the RESET button, then restart your session

Note: Do not confuse with the ODO (odometer), which displays the total accumulated distance of all your workouts and has no goal or countdown.

Question 5

What are the functions of the three buttons on the VirtuFit RB100 monitor?

Accepted Answer

The VirtuFit RB100 monitor has three buttons that allow you to control your workout:

MODE Button - Allows you to scroll through and select the desired display functions. A short press moves to the next function (time, speed, distance, calories, heart rate). A long press resets all values to zero and returns to automatic scan mode.
SET Button - Allows you to manually set target values for time, distance, pulse, and calories. This function is only available when automatic scan mode (SCAN) is disabled. Each set goal triggers a 10-second sound signal when achieved.
RESET Button - A short press resets the current session data (time, distance, calories) without affecting previously recorded data. A long press completely clears all data stored in memory.

The monitor operates by default in SCAN mode, where it automatically alternates between the five available functions, with each value displayed for 5 seconds before moving to the next. To measure your heart rate, place both hands firmly on the sensors located on the handles - the reading will display after 6 to 7 seconds.

Question 6

How to use the VirtuFit RB100 monitor?

Accepted Answer

Navigation and Display

The RB100 monitor displays five main data: time (00:00 to 99:59), speed (0.0 to 999.9 km/h), distance (0.00 to 999.9 km), calories (0.0 to 9999 kcal), and heart rate (40 to 240 bpm).

By default, the monitor operates in AUTO SCAN mode: it automatically switches between the five metrics, displaying each for 5 seconds. You don't need to do anything to navigate.

Control Buttons

Navigation/Arrow Button: Allows you to scroll and manually select a specific metric if you want to stay on a single data point.
SET Button: Allows you to set target values for time, distance, calories, and heart rate (not available in SCAN mode).
RESET Button: A brief press resets the values of your current session (time, distance, calories). A prolonged press clears all recorded data.

Heart Rate Measurement

The touch sensors are integrated into the bike's handlebars. Place your slightly damp hands on the two sensors and wait 6 to 7 seconds for the heart rate to display. Without continuous contact with the sensors, the heart rate will disappear.

Battery Life and Power Off

The monitor operates on 2 AAA batteries. In the absence of activity for 4 minutes, the screen automatically turns off. Press any button to reactivate it.

Alarms

When you have set target values (SET), a 10-second beep sounds when you reach your goal for time, distance, or calories.

User manual VirtuFit : user manuals and guides in PDF

Models VirtuFit most viewed

Browse manuals VirtuFit by appliance type

Recent questions about devices VirtuFit