Question 1

How to adjust the thread tension on the ELNA 3003 sewing machine?

Accepted Answer

On your ELNA 3003 sewing machine, the adjustment of the upper thread tension is done using the tension disc located on the upper front part of the machine, marked with numbers from 0 to 9.

Initial setting: Start with a medium position, around 4 or 5, which is generally suitable for standard thread and common fabrics like cotton or polyester.

To test the tension: Do a test on a piece of fabric identical to the one you will be sewing, using a straight stitch. Examine the resulting stitches to determine the necessary adjustments:

If the bobbin thread (bottom thread) is visible on the top of the fabric, the upper thread tension is too low: turn the disc towards the higher numbers (towards 6, 7, 8) clockwise to increase the tension.
If the needle thread (top thread) is visible on the bottom of the fabric, the tension is too high: turn the disc towards the lower numbers (towards 2, 3, 4) counterclockwise to decrease the tension.

Goal to achieve: The needle thread and the bobbin thread should interlock in the center of the two layers of fabric to achieve a strong and even stitch. The stitches should be balanced and tight.

Make adjustments in small increments of half a position at a time, then test again after each change. For decorative stitches or zigzag and overlock stitches, you may slightly reduce the tension so that the top thread is less visible on the back of the fabric.

If tension issues persist even after these adjustments, also check the bobbin tension via the small screw on the bobbin case. Incorrect bobbin tension can also significantly affect stitch quality and may require correction.

Question 2

Why does the thread frequently break on the ELNA 9500 sewing machine?

Accepted Answer

The thread frequently breaks on the ELNA 9500 generally for several avoidable reasons. This electronic sewing machine has computerized tension control and upper and lower thread sensors to detect problems, but regular maintenance and correct adjustments remain essential.

Start by checking the complete threading: make sure the upper thread passes correctly through all the thread guides and is positioned properly under the presser foot before you start sewing. Incorrect threading causes excessive tension that quickly breaks the thread. Also, check that the lower bobbin is wound evenly and inserted correctly into its case. On the ELNA 9500, the presence of lint around the bobbin often indicates an insertion or tension problem.

Next, adjust the thread tension according to your fabric. The ELNA 9500 has a computerized tension system, but you need to adapt the settings to the weight of the fabric used. If the thread breaks at the top, reduce the upper tension (lower number). Always test on a scrap of fabric before sewing your project. Too much tension is the most common cause of thread breakage.

Check the needle: replace it regularly as a dull, bent, or damaged needle can damage the thread. Ensure that the needle is properly inserted into its holder (the flat side facing the back) and that you are using the correct size for your fabric. A size 80/12 needle is suitable for fine fabrics, a 90/14 for medium fabrics, and a 100/16 or larger for thick fabrics.

Perform regular maintenance on the machine by cleaning the bobbin area and feed dogs after several hours of sewing. Use the provided brush to remove accumulated lint and dust, as these deposits can snag and break the thread. A well-maintained machine operates more reliably.

Use high-quality thread suitable for your fabric. Old, cheap, or unsuitable thread weakens and breaks easily. Also, check that the thread is not tangled around the spool.

If after these checks the problem persists, the machine may require professional adjustment of the tension system or inspection of its internal components. Contact ELNA customer service, which has spare parts and can diagnose other possible causes.

Question 3

How to sew a buttonhole with the ELNA 3005 sewing machine?

Accepted Answer

The ELNA 3005 sewing machine has a one-step automatic buttonhole function, making the operation simple and precise. Before you start, prepare your fabric: iron it carefully to make it flat. Mark the location and approximate length of the buttonhole with a tailor's pencil or chalk. For fine or stretchy fabrics, use interfacing (stabilizing fabric) on the reverse side of the fabric to stabilize the area and prevent distortion.

Set your machine by turning the stitch selector to "BH" (Buttonhole) to access the buttonhole mode. Check that the needle is in the high position by turning the balance wheel towards you. Raise the presser foot to facilitate the positioning of the fabric.

Attach the automatic buttonhole device R, provided with your machine. This device has a button holder at the back. Pull the button holder back and place your button inside, then push the button holder firmly to lock it. The size of the buttonhole will automatically adjust to the size of the button (the device accepts buttons up to 2.5 cm in diameter).

Place the fabric under the presser foot, aligning the marked point with the needle. Ensure there is no gap between the presser foot and the front of the device. Pass the thread from the needle under the presser foot. Lower the presser foot and the buttonhole will start automatically with the reinforcement stitches (bars). Sew slowly, allowing the machine to complete the full cycle automatically.

To finish, raise the buttonhole lever back to its initial position. Remove the fabric and cut the threads, leaving about 10 cm of tail. Pass the thread from the needle to the wrong side of the fabric by pulling the thread from the bobbin. Tie the threads securely on the reverse side. Carefully open the buttonhole by inserting a pin into one of the reinforcement bars and cutting with the buttonhole knife (provided) or small sharp scissors. Be careful not to cut the stitching. Insert your button to check that the size and stitching are correct.

Question 4

How to resolve a thread spool jam caused by the automatic tension on an ELNA 680 sewing machine?

Accepted Answer

Your ELNA 680 sewing machine is equipped with an automatic thread tension system that regulates the tension based on the selected stitch. A jammed thread spool is usually caused by excessive tension, a buildup of dust, or incorrect threading. Here’s how to effectively resolve this issue.

Step one: unlock the tension discs
Before any intervention, press the lockout key on your ELNA 680. This action lowers the presser foot and opens the upper thread tension discs. This allows the thread to release without excessive effort. Keep the machine locked for a few seconds, then press again to unlock.

Clear the jammed thread
Gently remove the jammed thread by gradually pulling it towards you. Do not use force, as this could break the thread or damage the guide. If the thread remains jammed, check that no fibers are tangled in the upper guide or threading path. Also inspect the entire thread path from the spool to the needle.

Clean the tension area
A buildup of dust or fibers can prevent the tension discs from functioning properly. Use a soft brush to gently clean the area around the tension discs and thread guides. Wipe a dry cloth through the upper threading path to remove any residue. On your ELNA 680, particularly clean the bobbin case at least once a month to avoid this kind of problem.

Thread correctly
Re-thread your machine by following the complete path: from the spool, through all the thread guides (including the tension guide), then into the lower bobbin guide according to the manual's diagram. The key is to ensure that the thread passes under all guiding elements without getting stuck. Check that the bobbin is properly positioned and that the thread flows freely.

Adjust the tension if necessary
The automatic tension of the ELNA 680 adapts to the selected stitch. However, if you continue to encounter issues after cleaning, you can manually adjust the tension using the “+” (to increase) or “-” (to decrease) buttons. Start from a neutral position and test on a scrap of fabric. If the tension remains problematic, this may indicate that the automatic system needs professional adjustment.

Future prevention
Use good quality thread suitable for your machine, regularly clean the threading path and thread guides, and replace worn needles that could snag the thread. If this problem persists despite these interventions, contact an authorized ELNA service center for a complete cleaning or repair of the automatic tension system.

Question 5

Why does the thread frequently break on my ELNA 680 sewing machine and how can I fix it?

Accepted Answer

The frequent breaking of the thread on your ELNA 680 usually has several causes. The two main causes concern the needle thread and the bobbin thread, each requiring specific checks.

For the needle thread, start by checking the threading: stop the machine, press the lock button to lock the machine, raise the thread tension lever to open the tension discs, and then completely re-thread the thread through all the threading points. Also, check that the needle is correctly inserted in its holder (it should be properly clicked in) and that it is not bent or dull. A damaged needle should be replaced immediately. Finally, make sure that the thread is properly placed under the presser foot before you start sewing, as a poor position can cause immediate breakage.

The thread tension may also be a factor. Although your ELNA 680 is equipped with an automatic tension control, you may need to manually adjust this tension according to your sewing conditions. If the tension is too tight, press the “–” button to gradually reduce it. Excessive tension is one of the most common causes of breakage, especially with poor quality threads or delicate fabrics.

For the bobbin thread, check that the thread is correctly threaded in the bobbin holder and that the bobbin is not damaged. A common problem is the accumulation of lint and debris in the bobbin holder: regularly clean this area with the lint brush provided with the machine. First, unplug the device, remove the bobbin holder and the bobbin, and then carefully brush the inside and outside. Also clean the feed dog and the automatic cutting device.

Also, check that you are using the correct bobbins: use only plastic bobbins marked “J” that are compatible with the horizontal hook of your machine. Incompatible bobbins can cause winding issues and breakage. Also consider the quality of the thread: use a good quality thread suitable for the type and thickness of the fabric you are sewing.

Finally, ensure that your machine is well maintained: keep the ventilation openings free of lint and dust, and regularly clean the inside of the machine as indicated in the manual. If after these checks the breakage persists, there may be a mechanical problem in the hook or tension discs that requires servicing by an authorized repairer.

Question 6

How to wind a bobbin with the ELNA 3005 sewing machine?

Accepted Answer

To wind a bobbin with your ELNA 3005 sewing machine, follow these simple steps:

Preparing the thread and bobbin

Choose a thread suitable for your project, preferably in the same color as the upper thread.
Place an empty bobbin on the designated bobbin holder on your machine.

Threading the thread for winding

Wrap the thread around the thread guide for winding the bobbin, usually located on the machine.
Insert the thread into the hole of the bobbin and pull it tight.

Activating the winding

Engage the bobbin winding mechanism by moving the lever or pressing the specific button for this purpose.
Gently press the pedal to start winding the thread onto the bobbin.

Finalization

Allow the bobbin to fill evenly; the mechanism will stop automatically once full, otherwise stop manually.
Remove the bobbin from the bobbin holder and cut the thread.
Your bobbin is now ready to be inserted into the bobbin case of your ELNA 3005 machine.

By following these steps, you will easily prepare your bobbins for all your sewing sessions with the ELNA 3005.

Question 7

Which stitch should I use on the ELNA 3003 sewing machine to make a hem on a fabric containing a lot of elastane?

Accepted Answer

To make a hem on a fabric containing a lot of elastane with your ELNA 3003 sewing machine, it is important to choose a stitch that offers flexibility so that the seam can stretch with the fabric without breaking.

Recommended stitches:

Zigzag stitch: This stitch is ideal for stretchy fabrics as it allows the seam to stretch. Set an appropriate width and length for the stitch to ensure it is strong yet flexible.
Stretch stitch (if available): Some machines offer a specific stretch stitch designed for elastic fabrics. Check if your ELNA 3003 has this option.

Tips for sewing the hem:

Fold the edge of the fabric over about 1 to 2 cm to form the hem.
Pin the fold carefully to hold it in place while sewing.
Select the zigzag or stretch stitch on your machine and adjust the settings (width and length) to achieve an elastic seam.
Sew slowly along the folded edge, ensuring that the stitch catches the fabric underneath well.

By using these stitches and techniques, you will achieve a clean, durable hem that is suitable for the stretchy properties of the fabric containing elastane.

User manual ELNA : user manuals and guides in PDF

Models ELNA most viewed

Browse manuals ELNA by appliance type

Recent questions about devices ELNA