Q: What is the CO mode on the Master DH 751?

The CO mode (Continuous) is a permanent dehumidification mode that automatically activates when the humidity level set on the Master DH 751 is set to less than 30%. In this mode, the device operates continuously without stopping, allowing for intensified dehumidification. The humidity display then shows "CO" to indicate that this mode is active. How to activate the CO mode: Use the "Humidity Decrease" button on the control panel to lower the humidity setting below 30%. Once the setting is confirmed to be below 30%, the "CO" symbol automatically appears on the screen and the device switches to continuous mode. How to deactivate the CO mode: Press the "Humidity Increase" button to raise the setting above 30%. The device then returns to normal operating mode with automatic stop/start. Practical operation: In normal mode (above 30%), the device starts when the current humidity exceeds your setting by 3%, and stops when it drops 3% below the setting. In CO mode, the device ignores this 3% threshold and operates continuously until it reaches a very low humidity level. The humidity display accepts settings between 30% and 90% relative humidity. The CO mode is particularly useful in very humid environments (basements, storage rooms, unventilated spaces) where prolonged and uninterrupted dehumidification is necessary to maintain optimal conditions. Remember to regularly empty the tank (capacity 2.5 liters): when it is full, an indicator lights up and the device stops operating.

Q: Where is the humidity indicator on the Master DH 751?

The humidity indicator is located on the control panel of the Master DH 751, identified as element #1 in figure 2 of the manual. This digital display indicates the current relative humidity level in the room. It shows values between 30% and 90% relative humidity. Operation: Upon startup, the screen displays the programmed humidity level (default 60%) for 3 seconds It then switches to the actual continuously measured humidity level If the humidity is set below 30%, the display shows "CO" (continuous mode) In case of malfunction, it may display error codes E1 or E2

Q: What does the filter of the Master DH 751 look like and where is it located?

The filter of the Master DH 751 , called the filter grille , is element 6 of the device's structure. It is a washable protective grille that prevents dust from damaging the compressor. This grille is not directly visible as it is protected by the front panel located on the side of the water tank . To locate and access the filter, you need to unscrew the front panel located at the front of the device, on the side of the water tank (panel 5). Once the panel is removed, the filter grille is directly accessible. The filter must be cleaned regularly to maintain the efficiency of the dehumidifier. The manual recommends cleaning at least once a month . In very dusty environments, cleaning should be done once a week, or even daily. To clean the filter, you have several options: gently tap the grille to dislodge dust, use a vacuum cleaner to remove heavier dirt, or wash the filter with warm water using neutral detergents (concentration ≤40%). After washing, make sure to let the filter dry completely before reinstalling it . Important: before handling the filter, turn off the device and unplug it from the power supply. If you do not use the device for an extended period, place the filter in a plastic bag to protect it from dust.

Question 1

What is the area or surface that the Master DH 751 can cover?

Accepted Answer

The Master DH 751 can process an air volume of 350 m³ per hour, which corresponds to an approximate area of 117 to 140 m² depending on your ceiling height (calculated based on a height of 2.5 to 3 meters). This device is therefore suitable for small to medium spaces such as bedrooms, offices, or small living rooms.

In addition, here are the dehumidification characteristics that will help you assess its effectiveness:

Dehumidification capacity: 46.7 liters per 24 hours (operating conditions: 30 °C and 80% relative humidity)
Air flow: 350 m³/h
Tank capacity: 5.7 liters
Adjustable humidity range: 20% to 90% RH
Power: 900 W
Noise level: ≤ 52 dB(A)

To determine if this area is suitable for you, consider the conditions of your space: a very humid environment (bathroom, basement) will require a longer operating time to reach the desired humidity level than a moderately humid space. The device also has a continuous mode and continuous drainage via a hose for prolonged operation without manual tank emptying.

Question 2

How does the air humidity conversion to water work on the Master DH 751?

Accepted Answer

The Master DH 751 dehumidifies the air by converting humidity into liquid water through a cooling and condensation system. Here’s how this process works:

Operating Steps

1. Intake of humid air - A fan draws in ambient air laden with humidity through the machine's filters.
2. Cooling and condensation - The compressor and refrigeration system cool this air. Humidity cannot remain in gaseous form at low temperatures and turns into water (condensation).
3. Collection of condensate - The resulting liquid water flows and collects in the tank (capacity of about 2.5 liters).
4. Discharge of dry air - The now dehumidified air is expelled into the room through the machine's outlets.

Automatic Regulation

The device maintains the humidity level you have set (between 30% and 90% RH):

Use the "Humidity increase" and "Humidity decrease" buttons on the control panel to adjust the desired humidity (1% per short press, 5% per second on prolonged press).
When the current humidity exceeds your setting by 3%, the compressor automatically activates.
It stops when the humidity drops 3% below your target.

Special Case: Continuous Mode (CO)

If you set the device below 30% humidity, it switches to continuous mode (marked "CO") on the display and operates continuously to reach this very low target.

Important Note

During operation, the machine generates heat. It is normal for the room temperature to rise slightly (1 to 3°C). This is part of the dehumidification process.

Question 3

What is the CO mode on the Master DH 751?

Accepted Answer

The CO mode (Continuous) is a permanent dehumidification mode that automatically activates when the humidity level set on the Master DH 751 is set to less than 30%. In this mode, the device operates continuously without stopping, allowing for intensified dehumidification. The humidity display then shows "CO" to indicate that this mode is active.

How to activate the CO mode: Use the "Humidity Decrease" button on the control panel to lower the humidity setting below 30%. Once the setting is confirmed to be below 30%, the "CO" symbol automatically appears on the screen and the device switches to continuous mode.

How to deactivate the CO mode: Press the "Humidity Increase" button to raise the setting above 30%. The device then returns to normal operating mode with automatic stop/start.

Practical operation: In normal mode (above 30%), the device starts when the current humidity exceeds your setting by 3%, and stops when it drops 3% below the setting. In CO mode, the device ignores this 3% threshold and operates continuously until it reaches a very low humidity level. The humidity display accepts settings between 30% and 90% relative humidity.

The CO mode is particularly useful in very humid environments (basements, storage rooms, unventilated spaces) where prolonged and uninterrupted dehumidification is necessary to maintain optimal conditions. Remember to regularly empty the tank (capacity 2.5 liters): when it is full, an indicator lights up and the device stops operating.

Question 4

Where is the humidity indicator on the Master DH 751?

Accepted Answer

The humidity indicator is located on the control panel of the Master DH 751, identified as element #1 in figure 2 of the manual.

This digital display indicates the current relative humidity level in the room. It shows values between 30% and 90% relative humidity.

Operation:

Upon startup, the screen displays the programmed humidity level (default 60%) for 3 seconds
It then switches to the actual continuously measured humidity level
If the humidity is set below 30%, the display shows "CO" (continuous mode)
In case of malfunction, it may display error codes E1 or E2

Question 5

What does the filter of the Master DH 751 look like and where is it located?

Accepted Answer

The filter of the Master DH 751, called the filter grille, is element 6 of the device's structure. It is a washable protective grille that prevents dust from damaging the compressor. This grille is not directly visible as it is protected by the front panel located on the side of the water tank.

To locate and access the filter, you need to unscrew the front panel located at the front of the device, on the side of the water tank (panel 5). Once the panel is removed, the filter grille is directly accessible.

The filter must be cleaned regularly to maintain the efficiency of the dehumidifier. The manual recommends cleaning at least once a month. In very dusty environments, cleaning should be done once a week, or even daily.

To clean the filter, you have several options: gently tap the grille to dislodge dust, use a vacuum cleaner to remove heavier dirt, or wash the filter with warm water using neutral detergents (concentration ≤40%). After washing, make sure to let the filter dry completely before reinstalling it.

Important: before handling the filter, turn off the device and unplug it from the power supply. If you do not use the device for an extended period, place the filter in a plastic bag to protect it from dust.

Question 6

Why does the circuit breaker trip when starting the Master DH 751?

Accepted Answer

The circuit breaker tripping at startup is generally caused by one of the following reasons:

Main cause: use of an extension cord or adapter

The manual clearly specifies not to use an extension cord or adapter. The Master DH 751 must be plugged directly into a wall outlet 220-240V ~ 50Hz. Extension cords increase the resistance of the circuit and often cause the circuit breaker to trip at startup.

Other possible causes

Startup overload: the dehumidification motor consumes a lot of energy at startup. If your circuit breaker is old or faulty, it may trip easily. Try plugging the device in alone on the circuit.
Internal short circuit: if the problem persists after removing the extension cord, the device may have an electrical fault. Stop using it and contact customer service.

Recommended actions

Plug the Master DH 751 directly into a wall outlet, without extension cord or adapter
Ensure that the wall outlet is functioning properly by testing another device
Check the condition of the main circuit breaker of your electrical installation

User manual Master : user manuals and guides in PDF

Models Master most viewed

Browse manuals Master by appliance type

Recent questions about devices Master