JA-80M - Sicherheitskamera Jablotron - Kostenlose Bedienungsanleitung
Finden Sie kostenlos die Bedienungsanleitung des Geräts JA-80M Jablotron als PDF.
| Produkttyp | Sicherheitskamera |
| Modell | JA-80M |
| Marke | Joblotron |
| Abmessungen (ca.) | 10 x 7 x 5 cm |
| Gewicht (ca.) | 300 g |
| Stromversorgung | DC 12V / 1A |
| Videoauflösung | Full HD 1080p |
| Nachtsicht | IR-LEDs, Reichweite bis zu 10 m |
| Bewegungserkennung | Ja, mit Push-Benachrichtigung |
| Blickwinkel | 120° |
| Speicher | MicroSD-Karte (bis 128 GB), Cloud-Speicher optional |
| Konnektivität | WiFi 2.4 GHz, Ethernet optional |
| App-Unterstützung | Joblotron View (iOS/Android) |
| Wetterfestigkeit | IP65 (für Außeneinsatz geeignet) |
| Reinigung | Linsen mit weichem, trockenem Tuch reinigen |
| Sicherheitshinweise | Nicht in der Nähe von Wasser oder Hitzequellen installieren |
| Ersatzteile | Netzteil, Montageset (im Lieferumfang); optional: Verlängerungskabel |
| Reparatur | Nur durch autorisiertes Fachpersonal |
| Allgemeine Informationen | Bitte lesen Sie die vollständige Bedienungsanleitung vor der Inbetriebnahme |
Häufig gestellte Fragen - JA-80M Jablotron
Benutzerfragen zu JA-80M Jablotron
0 Frage zu diesem Gerät. Beantworten Sie die, die Sie kennen, oder stellen Sie Ihre eigene.
Eine neue Frage zu diesem Gerät stellen
Laden Sie die Anleitung für Ihr Sicherheitskamera kostenlos im PDF-Format! Finden Sie Ihr Handbuch JA-80M - Jablotron und nehmen Sie Ihr elektronisches Gerät wieder in die Hand. Auf dieser Seite sind alle Dokumente veröffentlicht, die für die Verwendung Ihres Geräts notwendig sind. JA-80M von der Marke Jablotron.
BEDIENUNGSANLEITUNG JA-80M Jablotron
The JA-80M wireless magnetic door detector
The JA-80M is a component of Jablotron's Oasis 80 alarm system. It is designed to detect the opening of doors, windows etc. It can also be extended by a normally closed sensor. The battery-powered detector communicates via OASIS radio protocol.
Installation
Installation shall only be undertaken by technicians holding a certificate issued by an authorized distributor.
This detector reacts to the removal of its magnet unit. The electronics should be installed onto the non-moving part of windows or doors, and the magnet onto the moving part. The detector should be installed vertically. Avoid locating it directly on a metal frame as metal influences the functioning of the magnetic sensor and radio communication. If the door or window is made of metal, we recommend installing the detector unit away from the metal and wiring up an external wired magnetic sensor which is connected to the detector. See the following instructions:
5.1. Open the detector cover by pressing the tab in.
6.2. Screw the rear cover to the solid part of the door/window.
7.3. Attach the magnet to the moving part of the window. Its distance from the detector should not exceed 5mm when the door/window is closed. The lower edge of the magnet should be aligned with the lower edge of the detector. Only a single magnet can be installed, either on the left side or the right side of the
8.4. Leave the battery disconnected and the cover open and then follow the control panel or receiver manual. The basics of enrollment are:
4.1. Enter enrollment mode on the control panel by keying in "1" in Service mode.
5.2. Install a battery into the detector to activate enrollment.
6.3. Exit enrollment mode by pressing “#”
After installing a battery into the detector, allow up to 30 seconds for stabilisation. During this period the LED is continuously lit.
To enroll a detector after having already connected a battery, first disconnect the battery, and press and release the tamper sensor to discharge any remaining charge to ready the device for enrollment.
DIP switches
MG ON / MG OFF Allows the internal magnetic sensor inside the detector to be disabled when the detector is only to be used with external sensors wired to its terminals.
INS / DEL DEL provides entrance & exit delays for detectors installed in a building entrance. INS allows the detector to instantly trigger alarm activation if the control panel is armed. This DIP switch (INS/DEL) only has an effect if the detector has a natural reaction assigned to its address in the Oasis control panel. It also has no effect when used with a UC-8x or AC-8x receiver.
Opening the cover makes the detector react with a tamper signal.
Open/closed status detection
The detector is factory-set to indicate both opening and closing so that the control panel knows the status of doors/windows. If a pulse mode is desired to indicate only opening, keep the tamper switch pressed while installing the battery. Not pressing the tamper switch gives open and closed status signals.
Wiring up the external sensor
External sensors can be wired to the detector. It is possible to protect more doors/windows or to wire in other types of wired detectors. There are two inputs, IN and TMP which react when disconnected from the GND common terminal.
IN: If the IN terminal is disconnected from GND it sends the same signal to the control panel as if the magnet had been removed from the detector. The internal magnetic sensor can be disabled by DIP switch if desired.
TMP: The TMP terminal sends a tamper signal to the control panel if disconnected from GND.
Note: If any of these two inputs is not used, it must be shorted to the GND terminal.
Wiring example
Testing the detector
15 minutes after closing the detector cover, the LED indicates detector triggering. The strength and quality of detector signals can be measured by the control panel in Service mode.
Battery replacement
The detector monitors its battery voltage and if too low, a transmission is sent to the control panel to inform the installer or user. The detector continues to function and shows each triggering of the detector with a flash of its LED. Battery replacement should not be delayed by more than two weeks. This should be done by a qualified technician with the control panel in Service mode.
Expired batteries should not be thrown into the garbage, but disposed of according to local regulations.
Removing the detector from the system
If a detector is removed, the control panel announces the removal. The detector has to be deleted in the control panel before intentional removal.
Technical parameters
Voltage: Lithium battery type LS(T)14500 (3,6V AA)
Typical battery lifetime: approx. 3 years for 20 daily activations maximum
Communication band: 868 MHz, Oasis protocol
Communication range: approx. 300m (open area)
Typical sensitivity range of the built-in magnetic sensor 45/25mm
Inputs for external sensors IN and TMP = normally closed loops
Dimensions 110 x 31 x 26 mm
magnet: 56 x 16 x 15 mm
Operational environment according to EN 50131-1 II. Indoor general
Operational temperature range -10 to +40 °C
EN 50131-1, CLC/TS 50131-2-6, EN 50131-5-3 classification: grade 2
Complies with ETSI EN 300220, EN50130-4, EN55022, and EN 60950-1
Can be operated according to ERC REC 70-03
FCC ID VL6JA80M
Jablotron Ltd. hereby declares that the JA-80M is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC and complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications no expressly approved by Jablotron could void the user's authority to operate the equipment. The original of the conformity assessment can be found at www.jablotron.com, Technical Support section
Note: Although this product does not contain any harmful materials we suggest you
return the product to the dealer or directly to the producer after use.
Jablotron Ltd., Pod Skalkou 33 466 01 Jablonec nad Nisou Czech Republic
Tel.: +420 483 559 911
fax: +420 483 559 993
Internet: www.jablotron.com
Marke : Jablotron
Modell : JA-80M
Kategorie : Sicherheitskamera