JK114 - Tableau électrique HAGER - Notice d'utilisation et mode d'emploi gratuit

Type de produit	Disjoncteur magnéto-thermique
Marque	Hager
Modèle	JK114
Nombre de pôles	1 pôle + neutre
Courant nominal	16 A
Tension nominale	230/400 V AC
Pouvoir de coupure	10 kA
Courbe de déclenchement	Courbe C
Dimensions (L x H x P)	18 x 80 x 70 mm
Poids	120 g
Alimentation	Alimentation secteur intégrée
Température de fonctionnement	-5°C à +60°C
Indice de protection	IP20
Normes	IEC 60898-1, EN 60898-1
Fonctions principales	Protection contre les surcharges et les courts-circuits, sectionnement
Entretien et nettoyage	Nettoyer avec un chiffon sec, ne pas utiliser de solvants
Sécurité	Déclenchement en cas de défaut, isolation renforcée
Pièces détachées et réparabilité	Non réparable par l'utilisateur, remplacer l'appareil complet
Installation	Montage sur rail DIN, bornes à vis up to 25 mm²
Garantie	2 ans

FOIRE AUX QUESTIONS - JK114 HAGER

Quelle est la fonction principale du disjoncteur Hager JK114 ?

Le Hager JK114 est un disjoncteur magnéto-thermique conçu pour protéger les circuits électriques contre les surcharges et les courts-circuits, avec une fonction de sectionnement.

Quel est le courant nominal du JK114 ?

Le courant nominal est de 16 A, ce qui détermine le courant maximal que le disjoncteur peut supporter en fonctionnement normal.

Comment installer le disjoncteur Hager JK114 ?

Le JK114 se monte sur un rail DIN standard (35 mm). Les connexions se font via des bornes à vis pouvant accepter des conducteurs jusqu'à 25 mm².

Quelle est la tension de fonctionnement du JK114 ?

Il fonctionne sous une tension de 230/400 V AC, adapté aux réseaux monophasés et triphasés.

Que signifie la courbe C sur le JK114 ?

La courbe C indique un déclenchement magnétique entre 5 et 10 fois le courant nominal, adapté aux circuits d'éclairage et de prises.

Le Hager JK114 est-il réparable ?

Non, ce disjoncteur n'est pas réparable par l'utilisateur. En cas de défaut, il doit être remplacé entièrement.

Quel est l'indice de protection du JK114 ?

L'indice de protection est IP20, ce qui signifie qu'il est protégé contre les corps solides de plus de 12,5 mm, mais pas contre l'eau.

Peut-on utiliser le JK114 pour des applications triphasées ?

Oui, le JK114 est un pôle unique mais peut être utilisé dans un assemblage multipolaire pour des circuits triphasés en combinant plusieurs unités.

Comment entretenir le disjoncteur Hager JK114 ?

L'entretien se limite à un nettoyage sec avec un chiffon doux. N'utilisez pas de produits chimiques ou d'eau.

Quelle est la température de fonctionnement du JK114 ?

Le disjoncteur fonctionne dans une plage de température de -5°C à +60°C, convenant à la plupart des installations intérieures.

MODE D'EMPLOI JK114 HAGER

Blank
RCCB
RCBO (two module)
MCB
RCBO
Switch

ZD0651

graph TD
    A["Start"] --> B{Does device stayON?}
    B -->|YES| C["Use circuits normal"]
    B -->|NO| D{Does device supply pocket outlet?}
    D -->|YES| E["Call an electrician"]
    D -->|NO| F{Does device stayON?}
    F -->|YES| G["Plugh & switch appliance nata tim until device trips / brown identify fully appliance"]
    F -->|NO| H{Does device stayON?}
    H -->|YES| I["Use circuits normal"]
    H -->|NO| J{Does device stayON?}
    J -->|YES| K["Put ON MCBs device nata tim until RCCB trips again, identify fully appliquant"]
    J -->|NO| L["Call an electrician"]
    L --> M{Does device stayON?}
    M -->|YES| N["Plugh & switch appliance nata tim until device trips / brown identify fully appliance"]
    M -->|NO| O{Does device stayON?}
    O --> P["Plugh & switch appliance nata tim until device trips / brown identify fully appliance"]
    O -->|NO| Q["Call an electrician"]
    Q --> R{Does device stayON?}
    R -->|YES| S["Put ON MCBs device nata tim until RCCB trips again, identify fully appliquant"]
    R -->|NO| T["Put OFF all MCBs devices"]
    T --> U["Reset RCC B"]
    U --> V{Does device stayON?}
    V -->|YES| W["Put ON MCBs device nata tim until RCCB trips again, identify fully appliquant"]
    V -->|NO| X["Call an electrician"]
    X --> Y{Does device stayON?}
    Y -->|YES| Z["Plugh & switch appliance nata tim until device trips / brown identify fully appliance"]
    Y -->|NO| AA{Does device stayON?}
    AA -->|YES| AB["Put ON MCBs device nata tim until RCCB trips again, identify fully appliquant"]
    AA -->|NO| AC["Call an electrician"]
    AC --> AD{Does device stayON?}
    AD -->|YES| AE["Put ON MCBs device nata tim until RCCB trips again, identify fully appliquant"]
    AD -->|NO| AF["Put OFF all MCBs devices"]

Painted Metal Enclosure

Dimensions(mm)	Enclosure Size
	8	12	16	22	2x12	2x16	2x22	3x22
A	254	326	398	505	326	398	505	505
B	236	236	236	236	472	472	472	708
C	N/A	N/A	N/A	N/A	N/A	N/A	N/A	N/A
D	125	125	125	125	125	125	125	125

ZD0651

GB JKA Boards

Instructions/Data Sheet

ZD0651

This DBO and Hager devices conform with the following standards:

Meter Direct Fed EN 50476 RS EN 61420 2 including A

Switch-disconnectors: BS EN 60947-3

Residual Current Circuit Breaker (RCCB): BS EN 61008-1

Residual current operated circuit breaker with integral overload (RCBO): BS EN 61009-1

Miniature Circuit Breaker (MCB): BS EN 60898-1

Installation Instructions:

All product(s) must be installed by a suitably competent electrician. Giving consideration to their intended use and in accordance with the current edition of BS 7671 (IET Wiring Regulations).

The Electricity at Work regulations and the Health and Safety at Work Act shall be complied with.

Only equipment and arrangements specified in Hager's technical documentation / catalogue shall be used.

Install in the horizontal plane only.

Important notice:

To prevent potential overheating from loose connections the installer shall check connections are tight to the torque levels stated in these instructions prior to energizing this board. This check should include factory made connections which may have loosened in transit.

Tightening torque values to be applied (Nm)

Switch-disconnector's: 40A & 63A: 2.8 Nm

Switch-disconnector's: 100A: 3.6 Nm

RCCB's 40A & 63A: 2.8 Nm

RCCB's 80A & 100A: 3.3 Nm

MCBs: 2.8 Nm

RCBO's: 2.8 Nm

Earth & Neutral terminal bar connections: 2.0 Nm

Single conductors below 1.5mm ^2 need to be doubled back in the

terminal bar

Front metal cover fixing screws: 2.0 Nm

Meter torque: 2.4 Nm

Good workmanship and proper materials must be applied by the installer. The cable entry method shall, as far as reasonably practical, maintain the non-combustable arrangement of the enclosure. Account shall be taken of these instructions.

Cable entry facilities:

Metalclad units are provided with knockouts for standard 20, 25, and 32mm conduit and large rear knockouts.

Metal Unit - Removing and replacing the terminal rail for cabling:

Pull and lift the terminal bar support away from the unit resting the rail supported by the earth strap. After fixing conduit/ cable glands, locate the rail support and press down.

ZD0651

Note: Only BASEC approved cable should be used

1.0mm ^2 to 16mm ^2 for outgoing cables

up to 35.0mm² for incoming live cables

Single conductors below 1.5mm ^2 need to be doubled back in the terminal bar.

:hager

JKA Boards Instructions Sheet

:hager

JKA Boards Instructions Sheet

Guidance Notes:

The total load must not exceed the rating of the incoming device or the assigned assembly rating (InA) whichever is the lower. Each neutral and earth connection must correspond numerically to its outgoing way. Additional blanks (ref. JK01B) are available to cover spare ways.

A pack is provided to label this DBO, please consult us for spares or replacements.

Operating Instruction leaflet is provided overleaf. This leaflet should be left for the end user. Single conductors below 1.5mm² need to be doubled back in the terminal box.

Single conductors below 1.5mmH need to be doubled back in the terminal bar.

DBOs incorporating RCDs in TT systems should incorporate an S type (time Delayed) RCCB, e.g. 100 mA s-type RCCB. Alternatively a main

switch with RCBO protection on all outgoing circuits should be used.

Precautions need to be taken to prevent faults to earth on the supply side of the RCD (as per BS7671 regulation 531.4.1)

IP Ratings:

Cable access into the DBO must maintain the integrity so far as reasonably practicable. In essence, for surfaces accessible after installation, this means maintaining the requirement for the horizontal top surface of the enclosure to provide a degree of protection of at least IP4X and elsewhere, IP30. For rear cable access, the minimum number of knockout(s) shall be removed.

IP Code Description

IP2XC Protection against access with a tool (2.5mm diameter, 100mm long) making contact with live hazardous parts

IP30 Protection against access with a tool (2.5mm diameter, shall not penetrate)

IP4X A probe of 1mm diameter shall not enter the enclosure

Fitting Hager MCBs and RCBOs:

Only equipment and arrangements specified in Hager's technical
documentation / catalogue shall be used.
1. Isolate the electrical supply from the DBO.
2. Remove the front cover.
3. Fully slacken the lower terminal of the device.
4. Fully open the bottom device clip (fig 1.)

Warranty

This distribution board is offered with a 24 month warranty against defective material or manufacture. If a warranty claim is necessary, please call the technical support number given at the bottom of the page and we will be pleased to help.

For dimensional information and weights please consult the Hager catalogue.

Interface characteristics
Rated & operational voltage (Un / Ue)230V a.c. 50Hz
Rated insulation voltage (Ui)320V a.c. 50Hz
Rated impulse withstand voltage (Uimp)4kV
Rated current of the Assembly (InA)100A, 63ANote: Dependent upon rating of main incoming device
Rated current of an Outgoing circuit (Inc)MCB 6A - 63A (marked rated current on device)RCBO 6A - 50A (marked rated current on device)	Rated current of outgoing unit (Inc)RCCB 40A-100A (marked rated current on device)Direct Fed Meter - 100A (marked rated current on device)
Rated conditional short-circuit current of the ASSEMBLY (Icc)Annex ZB: 16 kA rms at 250V, power factor 0.6 with equipment and arrangements specified in Hager's technical documentation / catalogue. (Does not include metered type A distribution boards)JK A Board DBO Icc = 10kA, Ipk 17kA
Protection against electric shockConsumer unit shall be installed in an electrical system conforming to the current edition of IEC 60364 / BS 7671
Rated diversity factor (RDF) / Values of assumed loading1way = 1.02way - 3way = 0.84way - 5way = 0.76way - 9way = 0.610way and above = 0.5	Note: RDF only applies to continuously and simultaneously loaded circuits.In principle, this means adjacent circuit-breakers having a load 'on' time exceeding 30 minutes or where a load not exceeding 30 minutes has an 'off' time less than the 'on' time, will need to have the rated diversity factor applied as indicated.
Rated frequency (fn)50 Hz
Pollution degree2
Types of system earthing for which the ASSEMBLY is designedTNC-S, TN-S when installed in an electrical installation complying with BS 7671Hager recommends for TT systems a 100A type S time delayed RCCB or a main switch with RCBO protection only on all outgoing circuits.
Indoor use only
Stationary ASSEMBLY
Degree of protectionIP2XC with door open and full compliment of outgoing devices and or blanks fitted.IP30 with door closed and full compliment of outgoing devices and or blanks fitted.Note: Where cables are installed through top wall of enclosure, gaps of IP4X to be maintained.
Intended useIntended for use in domestic (residential) or similar premises.
Electromagnetic compatibility (EMC) classificationEMC Environment B
External designJKA: Wall-mounted, surface type, enclosed assembly.
Mechanical impact protectionIK 05
The type of constructionFixed parts
Type A DBO (Distribution board for use by ordinary persons)