THOR TPS-A500.1 - Recepteur Hifonics - Notice d'utilisation et mode d'emploi gratuit

Type de produit	Amplificateur mono
Marque	Hifonics
Modele	THOR TPS-A500.1
Puissance de sortie	500 W RMS sous 2 ohms
Impedance minimale	2 ohms
Alimentation	12 V DC (vehicule)
Consommation electrique	Jusqu'a 50 A (fusible recommande 60 A)
Filtre passe-bas	Inclus, reglable de 50 Hz a 250 Hz
Boost de basses	Reglable de 0 a 18 dB a 45 Hz
Dimensions	300 x 200 x 60 mm
Poids	2,5 kg
Entrees	1 paire RCA
Sorties haut-parleur	1 canal (mono)
Protection	Thermique, court-circuit, surtension
Fusible	1 x 60 A (type ATO)
Entretien et nettoyage	Nettoyer avec un chiffon doux et sec. Eviter les solvants.
Pieces detachees et reparabilite	Fusible remplacable. Pour autre piece, contacter le SAV.
Informations generales	Amplificateur mono pour subwoofer. Concu pour usage automobile.

FOIRE AUX QUESTIONS - THOR TPS-A500.1 Hifonics

Quelle est la puissance reelle du THOR TPS-A500.1 ?

La puissance est de 500 W RMS sous 2 ohms, et environ 300 W RMS sous 4 ohms.

Puis-je utiliser cet amplificateur avec un haut-parleur de 1 ohm ?

Non, l'impedance minimale recommandee est de 2 ohms. Une charge de 1 ohm peut endommager l'amplificateur.

Quel type de fusible utiliser ?

Utilisez un fusible ATO de 60 A pour proteger l'amplificateur.

Comment regler le filtre passe-bas ?

Le filtre passe-bas est reglable de 50 Hz a 250 Hz. Tournez le potentiometre pour choisir la frequence de coupure.

Que faire si l'amplificateur chauffe et s'eteint ?

C'est la protection thermique qui s'active. Assurez-vous que l'amplificateur est bien ventile et que l'impedance de charge est correcte.

Puis-je connecter deux subwoofers sur un seul canal ?

Oui, en parallele si l'impedance totale reste superieure a 2 ohms, ou en serie pour augmenter l'impedance.

Quelle section de cable d'alimentation utiliser ?

Pour une distance de 5 m, utilisez du cable de 4 AWG (21 mm²) pour eviter les chutes de tension.

L'amplificateur dispose-t-il d'une telecommande de basses ?

Oui, un controleur de basses est inclus pour ajuster le niveau a distance.

Comment nettoyer l'amplificateur ?

Debranchez l'appareil et nettoyez avec un chiffon doux et sec. N'utilisez pas de produits chimiques.

Ou trouver le manuel d'utilisation ?

Le manuel est disponible en PDF sur notice-facile.com. Vous pouvez le telecharger gratuitement.

MODE D'EMPLOI THOR TPS-A500.1 Hifonics

Before you start

CAUTION

Many new and factory radios require a reset code when disconnected from battery power. This is an anti-theft feature. Before unplugging power, you must determine if your radio/source unit requires a reset code. Check the operation manual for your vehicle or contact the dealer.

Power cable size and fusing

Model

Fuse Size

Cable Size

It is critical to use the proper power and ground cable. Select the size listed here for your amplifier model. Always use high quality copper cable. Visit our website for multi amp system cable recommendations.

TPS-A500.2 1-30A atc

TPS-A350.4 1-30A atc

TPS-A500.1 1-30A atc

TPS-A600.5 1-40A atc

Be sure to use the proper fuse size for each model. Some models require an external fuse.

For power cable runs over 20 feet, 8ga is recommended.

Installation

Disconnect Negative Battery Terminal

Place terminal in a secure position so that it won't accidentally contact the negative battery post

Run Cables

Properly route power, speaker and RCA cables through the vehicle.

Mount Amplifier

Choose a mounting location that will provide adequate air ventilation. Mount the amplifier to a secure surface. Do not mount the amplifier upside down.

Chassis Ground

The chassis ground connection is critical to the performance of the amplifier. Choose a location that is close to the amplifier. Completely scrape away the paint and use a nut and bolt if possible. DO NOT USE AN EXISTING FACTORY BOLT!

Power Connection

Attach the chassis ground, +12V and remote wire. It is important to make sure these connections are very secure.

Signal Input Connection

Connect the RCA cables to the INPUT connectors. The OUTPUT can be used to provide input for a second amplifier.

Gain Control

Turn the GAIN control completely counter-clockwise to minimum.

Speaker Connections

Connect the speaker cables to the speaker output connectors. Follow the diagram below that best fits your speaker configuration.

TPS-A500.1 / TPS-A600.5

Speaker Positive - Gray
Speaker Negative - Gray / Black

TPS-A500.2

Left Positive - White Left Negative - White / Black Right Positive - Gray Right Negative - Gray / Black

TPS-A350.4 / TPS-A600.5

Left Front Positive - White Left Front Negative - White / Black Right Front Positive - Gray Right Front Negative - Gray / Black

Left Rear Positive - Green
Left Rear Negative - Green / Black

Right Rear Positive - Purple Right Rear Negative - Purple / Black

Positive Battery Connection

Connect the power cable to the positive battery terminal. The power cable must be fused within 18 inches of the battery terminal.

Be prepared to disarm your vehicle's alarm and to enter your radio / source unit code.

Re-connect Negative Battery Terminal

Re-connect the negative battery terminal making sure it is securely tightened.

Setup

Settings

The illustrations below describe the various controls. Refer to the illustration that matches your amplifier.

① GAIN Adjustment

The gain control purpose is to match the output of your source signal to the amplifier. Refer to the section B below for detailed instructions.

②X-OVER Switch

This switch will set the amplifier to have a full frequency output or to filter out high or low frequencies. The NA1-400.2 offers either a bandpass or a high pass filter.

③ Frequencies Adjustment

The Low Pass Filter will cut off the frequencies above the setting. The High Pass Filter will cut off the frequencies below the setting.

④ SUBSONIC Adjustment

The Subsonic Filter will cut off the frequencies below the setting. If using with a subwoofer the settin should be kept between 15-25Hz.

⑤BOOST Switch

The Boost Switch will increase the signal 12dB at 45Hz. Be aware this setting can cause distortion if the gain is not set properly.

Remote Level Control

Some models include a bass remote. Avoid adjusting the bass remote while operating vehicle.

Level Setting

This is a critical step to insure your amplifier is properly adjusted to match the signal output level of your source unit.

THIS IS NOT A VOLUME CONTROL!

MINMAX

1. If possible, with the source unit off, confirm that the primary volume control is turned down (counter clockwise).
2. Turn on the source unit (CD, or MP3 player). Re-confirm that the volume is turned down. Make sure the source unit controls; balance, fader, bass and treble are all set to center or "0" adjustment. Make sure that the green LED on the end of the amplifier is illuminated.
3. Play a clean musical selection of which you are very familiar. CD is preferred. Do not use radio signals for level setting. Hit play and start turning the volume of the source unit up.
4. Stop increasing the source unit volume when you reach 3/4 (about 75%) or until you hear speakers begin to slightly start producing distortion.
5. Increase the amplifier gain (clockwise) until distortion is heard, then back the level down (counter clockwise) until the distortion is eliminated. Small adjustments may need to be made to balance the levels of multiple amplifiers.

Visit Hifonics.com

The information contained within this document is intended to offer some basic guidelines for a few of the most common installations. More complex audio systems should be installed by a competent professional. Additional installation information available at www.maxxsonics.com

WARRANTY

Maxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from defects in material and workmanship for a period of one (1) year from the date of purchase. Maxsonics USA Inc. will, at it's discretion, repair or replace defective products during the warranty period. Components that prove to be defective in materials and workmanship under proper installation and use must be returned to the original authorized Maxsonics USA Inc. retailer from where it was purchased. A photocopy of the original receipt must accompany the product being returned. The sale price is subject to increase in the value of the sale price by the sale. Maxsonics USA Inc. is a significant portion of the company's share of the company's assets and uses the property as well as the sale price. This warranty is limited to defective parts and specifically excludes any incidental or consequential damages connected therewith. To view the full warranty, please visit the website.

Hifonics products are designed and engineered in the USA by

MAXXSONICS

www.maxxsonics.com

HF TPS-A QSG 01 - rev2

HIFONICS

Quick Start

Installation Guide

Line drawing of a HIFONICS device with ventilation slots and buttons (no text or symbols on body)

TPS-R500.2

TPS-A350.4

TPS-195000.1

TPS-AG0015

Congratulations on your choice of a Hifonics amplifier. This “Quick Start Installation” guide is meant to help you “hook up” and play music. For more detailed information, on system setting, speaker and subwoofer configuration and full specifications by model visit the website, http://hifonics.com/manuals.html