JK024 - Tableau électrique HAGER - Notice d'utilisation et mode d'emploi gratuit

Type de produit	Disjoncteur modulaire
Marque	Hager
Modèle	JK024
Nombre de pôles	2P
Courant nominal	24 A
Tension nominale	230/400 V AC
Pouvoir de coupure	6 kA
Courbe de déclenchement	Courbe C
Montage	Sur rail DIN
Dimensions (L × H × P)	18 mm × 85 mm × 69 mm
Poids	120 g
Alimentation	Réseau 50/60 Hz
Température de fonctionnement	-25 °C à +60 °C
Indice de protection	IP20 (bornes) / IP40 (face avant)
Normes de référence	NF EN 60898-1
Capacité de raccordement	1 à 25 mm²
Fonctions principales	Protection contre les surcharges et courts-circuits
Entretien et nettoyage	Nettoyer à sec avec un chiffon doux ; ne pas utiliser de solvant
Sécurité	Disjoncteur à déclenchement libre ; ne pas réarmer en cas de défaut persistant
Pièces détachées et réparabilité	Produit non réparable ; remplacer par un modèle identique

FOIRE AUX QUESTIONS - JK024 HAGER

Comment installer le disjoncteur JK024 ?

Installez le disjoncteur sur un rail DIN dans un tableau électrique. Coupez l'alimentation avant toute intervention. Respectez le sens du courant (entrée par le haut).

Quel est le courant nominal du JK024 ?

Le courant nominal est de 24 A.

Le JK024 est-il adapté pour une utilisation en triphasé ?

Le modèle JK024 est un disjoncteur bipolaire (2P). Il peut être utilisé en monophasé ou pour protéger une phase et le neutre. Pour une utilisation triphasée, utilisez un modèle tétrapolaire.

Que signifie la courbe C sur ce disjoncteur ?

La courbe C indique un déclenchement magnétique entre 5 et 10 fois le courant nominal. Elle convient aux circuits résistifs et inductifs légers (éclairage, prises).

Quelle est la tension maximale supportée par le JK024 ?

Le JK024 supporte une tension nominale de 230/400 V AC.

Puis-je réparer un disjoncteur JK024 qui ne fonctionne plus ?

Non, le disjoncteur est un dispositif scellé non réparable. En cas de défaut, remplacez-le par un modèle identique de même calibre et courbe.

Comment nettoyer le disjoncteur JK024 ?

Nettoyez l'enveloppe extérieure avec un chiffon doux et sec. N'utilisez pas de produits chimiques ou abrasifs.

Quelle est la section de câble maximale à connecter ?

La capacité de raccordement est de 1 à 25 mm² pour les conducteurs rigides ou souples.

Le JK024 est-il conforme aux normes européennes ?

Oui, il est conforme à la norme NF EN 60898-1.

Que faire si le disjoncteur saute fréquemment ?

Vérifiez d'abord si un appareil défectueux ou une surcharge est en cause. Si le problème persiste, faites vérifier l'installation par un électricien qualifié. Ne remplacez pas le disjoncteur par un calibre supérieur sans diagnostic.

MODE D'EMPLOI JK024 HAGER

Blank
RCCB
RCBO (two module)
MCB
RCBO
Switch

ZD0651

graph TD
    A["Start"] --> B{Does device stayON?}
    B -->|YES| C["Use circuits normal"]
    B -->|NO| D{Does device supply pocket outlet?}
    D -->|YES| E["Call an electrician"]
    D -->|NO| F{Does device stayON?}
    F -->|YES| G["Plugh & switch appliance nata tim until device trips / brown identify fully appliance"]
    F -->|NO| H{Does device stayON?}
    H -->|YES| I["Use circuits normal"]
    H -->|NO| J{Does device stayON?}
    J -->|YES| K["Put ON MCBs device nata tim until RCCB trips again, identify fully appliquant"]
    J -->|NO| L["Call an electrician"]
    L --> M{Does device stayON?}
    M -->|YES| N["Plugh & switch appliance nata tim until device trips / brown identify fully appliance"]
    M -->|NO| O{Does device stayON?}
    O --> P["Plugh & switch appliance nata tim until device trips / brown identify fully appliance"]
    O -->|NO| Q["Call an electrician"]
    Q --> R{Does device stayON?}
    R -->|YES| S["Put ON MCBs device nata tim until RCCB trips again, identify fully appliquant"]
    R -->|NO| T["Put OFF all MCBs devices"]
    T --> U["Reset RCC B"]
    U --> V{Does device stayON?}
    V -->|YES| W["Put ON MCBs device nata tim until RCCB trips again, identify fully appliquant"]
    V -->|NO| X["Call an electrician"]
    X --> Y{Does device stayON?}
    Y -->|YES| Z["Plugh & switch appliance nata tim until device trips / brown identify fully appliance"]
    Y -->|NO| AA{Does device stayON?}
    AA -->|YES| AB["Put ON MCBs device nata tim until RCCB trips again, identify fully appliquant"]
    AA -->|NO| AC["Call an electrician"]

Painted Metal Enclosure

Dimensions(mm)	Enclosure Size
	8	12	16	22	2x12	2x16	2x22	3x22
A	254	326	398	505	326	398	505	505
B	236	236	236	236	472	472	472	708
C	N/A	N/A	N/A	N/A	N/A	N/A	N/A	N/A
D	125	125	125	125	125	125	125	125

ZD0651

GB JKA Boards

Instructions/Data Sheet

ZD0651

This DBO and Hager devices conform with the following standards:

Meter Direct Fed EN 50470

BS EN 61439-3 including Annex ZB.

Switch-disconnectors: BS EN 60947-3. Residual Current Circuit Breaker (RCCR): BS EN 61008-1

Residual current operated circuit breaker with integral overload (RCRO): RS EN 61000.1

Residual current operated circuit breaker with in Miniature Circuit Breaker (MCB): BS EN 60898-1

Installation Instructions:

All product(s) must be installed by a suitably competent electrician. Giving consideration to their intended use and in accordance with the current edition of BS 7671 (IET Wiring Regulations).

The Electricity at Work regulations and the Health and Safety at Work Act shall be complied with.

Only equipment and arrangements specified in Hager's technical documentation / catalogue shall be used.

Install in the horizontal plane only.

Important notice:

To prevent potential overheating from loose connections the installer shall check connections are tight to the torque levels stated in these instructions prior to energizing this board. This check should include factory made connections which may have loosened in transit.

Tightening torque values to be applied (Nm)

Switch disconnector's: 40A & 63A; 2.8 Nm

Switch-disconnector's: 100A; 3.6 Nm

Switch-disconnector s. 100A BCCB's 40A & 63A: 2.8 Nm

RCCB's 40A & 63A: 2.8 Nm RCCB's 80A & 100A: 3.3 Nm

ROCB 5.00A & 100A, 3.5 Nm MCPa: 2.8 Nm

MCBS: 2.8 Nm BCRO'ev: 2.8 Nm

RCBO S. 2.8 Nm Earth & Neutral terminal box connections: 2.0 Nm

Earth & Neutral terminal bar connections. 2.0 Nm Single conductors below 1.5mm ^2 need to be doubled back in the

Single conductors below 1.5mm- need to be doubled back in the terminal bar.

terminal bar Front metal

Front metal cover fixing screws. 2.0 Nm Meter torque: 2.4 Nm

Meter torque. 2.4 Nm

Good workmanship and proper materials must be applied by the installer. The cable entry method shall, as far as reasonably practical, maintain the non-combustable arrangement of the enclosure. Account shall be taken of these instructions.

Cable entry facilities:

Metalclad units are provided with knockouts for standard 20, 25, and 32mm conduit and large rear knockouts.

Metal Unit - Removing and replacing the terminal rail for cabling:

Pull and lift the terminal bar support away from the unit resting the rail supported by the earth strap. After fixing conduit/ cable glands, locate the rail support and press down.

ZD0651

Note: Only BASEC approved cable should be used

1.0mm² to 16mm² for outgoing cables

up to 35.0mm² for incoming live cables

Single conductors below 1.5mm ^2 need to be doubled back in the terminal bar.

:hager

JKA Boards Instructions Sheet

:hager

JKA Boards Instructions Sheet

Guidance Notes:

The total load must not exceed the rating of the incoming device or the assigned assembly rating (InA) whichever is the lower. Each neutral and earth connection must correspond numerically to its outgoing way. Additional blanks (ref. JK01B) are available to cover spare ways.

A pack is provided to label this DBO, please consult us for spares or replacements.

Operating Instruction leaflet is provided overleaf. This leaflet should be left for the end user. Single conductors below 1.5mm² need to be doubled back in the terminal box.

Single conductors below 1.5mmH need to be doubled back in the terminal bar.

DBOs incorporating RCDs in TT systems should incorporate an S type (time Delayed) RCCB, e.g. 100 mA s-type RCCB. Alternatively a main

switch with RCBO protection on all outgoing circuits should be used.

Precautions need to be taken to prevent faults to earth on the supply side of the RCD (as per BS7671 regulation 531.4.1)

IP Ratings:

Cable access into the DBO must maintain the integrity so far as reasonably practicable. In essence, for surfaces accessible after installation, this means maintaining the requirement for the horizontal top surface of the enclosure to provide a degree of protection of at least IP4X and elsewhere, IP30. For rear cable access, the minimum number of knockout(s) shall be removed.

IP Code Description

IP2XC Protection against access with a tool (2.5mm diameter, 100mm long) making contact with live hazardous parts

IP30 Protection against access with a tool (2.5mm diameter, shall not penetrate)

IP4X A probe of 1mm diameter shall not enter the enclosure

Fitting Hager MCBs and RCBOs:

Only equipment and arrangements specified in Hager's technical
documentation / catalogue shall be used.
1. Isolate the electrical supply from the DBO.
2. Remove the front cover.
3. Fully slacken the lower terminal of the device.
4. Fully open the bottom device clip (fig 1.)

Warranty

This distribution board is offered with a 24 month warranty against defective material or manufacture. If a warranty claim is necessary, please call the technical support number given at the bottom of the page and we will be pleased to help.

For dimensional information and weights please consult the Hager catalogue.

Interface characteristics
Rated & operational voltage (Un / Ue)230V a.c. 50Hz
Rated insulation voltage (Ui)320V a.c. 50Hz
Rated impulse withstand voltage (Uimp)4kV
Rated current of the Assembly (InA)100A, 63ANote: Dependent upon rating of main incoming device
Rated current of an Outgoing circuit (Inc)MCB 6A - 63A (marked rated current on device)RCBO 6A - 50A (marked rated current on device)	Rated current of outgoing unit (Inc)RCCB 40A-100A (marked rated current on device)Direct Fed Meter - 100A (marked rated current on device)
Rated conditional short-circuit current of the ASSEMBLY (Icc)Annex ZB: 16 kA rms at 250V, power factor 0.6 with equipment and arrangements specified in Hager's technical documentation / catalogue. (Does not include metered type A distribution boards)JK A Board DBO Icc = 10kA, Ipk 17kA
Protection against electric shockConsumer unit shall be installed in an electrical system conforming to the current edition of IEC 60364 / BS 7671
Rated diversity factor (RDF) / Values of assumed loading1way = 1.02way - 3way = 0.84way - 5way = 0.76way - 9way = 0.610way and above = 0.5	Note: RDF only applies to continuously and simultaneously loaded circuits.In principle, this means adjacent circuit-breakers having a load 'on' time exceeding 30 minutes or where a load not exceeding 30 minutes has an 'off' time less than the 'on' time, will need to have the rated diversity factor applied as indicated.
Rated frequency (fn)50 Hz
Pollution degree2
Types of system earthing for which the ASSEMBLY is designedTNC-S, TN-S when installed in an electrical installation complying with BS 7671Hager recommends for TT systems a 100A type S time delayed RCCB or a main switch with RCBO protection only on all outgoing circuits.
Indoor use only
Stationary ASSEMBLY
Degree of protectionIP2XC with door open and full compliment of outgoing devices and or blanks fitted.IP30 with door closed and full compliment of outgoing devices and or blanks fitted.Note: Where cables are installed through top wall of enclosure, gaps of IP4X to be maintained.
Intended useIntended for use in domestic (residential) or similar premises.
Electromagnetic compatibility (EMC) classificationEMC Environment B
External designJKA: Wall-mounted, surface type, enclosed assembly.
Mechanical impact protectionIK 05
The type of constructionFixed parts
Type A DBO (Distribution board for use by ordinary persons)