TM26GT - Lampe de poche Nitecore - Notice d'utilisation et mode d'emploi gratuit

Type de produit	Lampe de poche LED puissante
Marque	Nitecore
Modèle	TM26GT
Source lumineuse	4 x LED CREE XM-L2 U2
Flux lumineux maximal	4000 lumens
Portée du faisceau	Jusqu'à 420 mètres
Intensité lumineuse	45 000 candela
Alimentation	4 x batteries 18650 (rechargeables) ou 8 x CR123
Dimensions	Longueur : 125 mm, Diamètre de la tête : 66 mm, Diamètre du corps : 43 mm
Poids (sans piles)	Environ 283 g
Matériau du boîtier	Alliage d'aluminium aéronautique (HA III)
Résistance aux chocs	1,5 mètres
Étanchéité	IPX-8 (immersion jusqu'à 2 mètres)
Modes d'éclairage	Turbo, Fort, Moyen, Faible, Ultra-faible, SOS, Balise, Stroboscope
Fonctions avancées	Indicateur de niveau de batterie, verrouillage, mémorisation du dernier mode
Entretien et nettoyage	Nettoyer les contacts avec un chiffon sec. Éviter les solvants. Vérifier les joints toriques.
Sécurité	Protection contre l'inversion de polarité, protection thermique intégrée
Pièces détachées et réparabilité	Joints toriques, piles, chargeur disponibles. Réparation par un professionnel recommandé.
Garantie	Garantie limitée du fabricant (consulter la notice)

FOIRE AUX QUESTIONS - TM26GT Nitecore

Comment allumer et éteindre la lampe Nitecore TM26GT ?

Appuyez sur le bouton latéral (interrupteur) pour allumer/éteindre. Maintenez enfoncé pour changer de mode.

Quels types de piles recommander pour la TM26GT ?

Utilisez des piles 18650 rechargeables (protégées) ou des piles CR123. Évitez les piles non rechargeables alcalines.

Comment passer en mode Turbo ?

En mode Allumé, appuyez rapidement deux fois sur le bouton pour activer le mode Turbo (pleine puissance).

La lampe chauffe-t-elle normalement ?

Oui, en mode Turbo ou Fort, la lampe peut chauffer. Le système de gestion thermique réduit automatiquement la puissance si nécessaire.

Comment verrouiller la lampe pour éviter un allumage accidentel ?

Éteignez la lampe, puis maintenez le bouton enfoncé pendant environ 3 secondes jusqu'à ce que la lampe clignote. Le verrouillage est activé.

Que signifie le voyant indicateur de batterie ?

Le voyant à l'arrière indique le niveau de batterie : vert (bon), jaune (moyen), rouge (faible). Clignotant rouge = batterie critique.

Puis-je utiliser la lampe sous la pluie ?

Oui, la TM26GT est étanche IPX-8, elle peut résister à une immersion jusqu'à 2 mètres. Utilisation sous la pluie sans problème.

Comment nettoyer la lampe ?

Essuyez l'extérieur avec un chiffon doux et sec. Pour les contacts, utilisez un coton-tige imbibé d'alcool isopropylique. Lubrifiez les joints toriques avec du silicone.

La lampe a-t-elle une mémoire de mode ?

Oui, la TM26GT mémorise le dernier mode utilisé (sauf Turbo et stroboscope) lors de la prochaine extinction.

Où puis-je trouver des pièces de rechange ?

Contactez le service client Nitecore ou un revendeur agréé. Les joints toriques et les piles sont disponibles séparément.

MODE D'EMPLOI TM26GT Nitecore

General Operation

NB: The TM26GT utilizes a 2-stage switch. The light's numerous functions can be accessed according to the depth the switch is pressed.

The TM26GT has two modes: Daily mode and Search mode. With the TM26GT turned off, pressing the switch partway down will activate Daily mode.

Alternatively, with the TM26GT turned off, pressing the switch all the way down will activate search mode. The TM26GT is turned off by pressing the switch all the way down.

Brightness Selection in Daily Mode

1. In Daily mode, press the switch partway down to select a brightness level of ultra-low, low, medium or high. The selected brightness level will be memorized when the light is turned off.
2. In Daily mode, press the switch partway down and hold to enter turbo mode. A second partway press will revert back to the brightness level last used.

Brightness Selection in Search Mode

In Search mode, press the switch partway down to cycle between high and turbo-high levels. There is no memory effect in Search mode.

Momentary Daily / Search Mode

1. With the TM26GT turned off, press the switch partway down and hold to activate Momentary Daily mode. Release the switch to turn the light off again.
2. With the TM26GT turned off, press the switch all the way down and hold to enter Momentary search mode. Release the switch to turn the light off again.

Standby Mode

With the TM26GT turned on, press the switch all the way down and release within one second to enter standby mode. In this mode, the light will consume small amounts of power to maintain the settings in the MCU (Micro Control Unit). When in standby mode the power indicator light will flash once every three seconds to show the location of the light.

OLED Display

1. When the TM26GT is turned on, the OLED display will activate automatically and show lumen output, brightness mode, battery voltage, battery status, approximate runtime and temperature. After displaying this information for several seconds the OLED display will turn off. The display can be reactivated by pressing the display switch and the information can be cycled through with subsequent presses of the switch.
2. When in Standby mode, a single press on the OLED display switch will activate the OLED and display battery voltage for 10 seconds.
3. When using Nitecore's NBP52 high-performance battery pack, the actual runtime will be twice the figure displayed on the OLED panel.
   Note: The TM26GT has an integrated thermal protection circuit which prevents overheating. Please refer to the "Thermal protection" section of this manual for details.

Special Strobe / SOS mode and Location Beacon

With the light turned on, press the switch all the way down twice in quick succession to access strobe mode. When in strobe mode, press the switch partway down to cycle through SOS, location beacon and strobe modes. To select any of these modes simply release the switch when it is displayed. To turn off the light (enter into standby mode) fully press and release the switch.

Note: When in any of the special modes, the OLED display will remain on to display which mode is being used.

Demonstration Mode

When entering standby mode simultaneously press and hold the display switch and the on/off switch to enter into Demonstration mode. In Demonstration mode, the OLED screen will cycle through the TM26's various messages. Simply press any button to exit Demonstration mode.

Lockout Function

With the light turned on, press the switch all the way down and hold for more than one second. The light will turn off and enter lockout mode. Lockout mode consumes almost no battery power and prevents the light from accidental activation. Simply press and hold the switch all the way down for more than one second to exit lockout mode.

Note:

1. If the display button is pressed in lockout mode, the OLED display will show

the words "LOCK OUT" as a reminder.
2. When TM26GT is kept in a backpack or left unused for extended periods, Nitecore recommends the battery compartment is loosened to cut off the power entirely, thus saving battery power and preventing accidental activation of the flashlight.

Power Tips

1. With the light turned, the power indicator will blink once every two seconds when power levels are below 50%.
2. With the light turned, the power indicator will blink rapidly when power levels are below 10%.

Note: When the light is being used in ultra-low mode, the blue power indicator will turn off to help conserve power.

Thermal Protection

As the TM26GT is very compact, extended operation in Turbo mode will cause the body temperature to continually rise, thus, making it too hot to comfortably hold. As a result, Nitecore does not recommend using the TM26 in Turbo mode for extended periods. The TM26 has an integrated thermal protection circuit which prevents overheating. With the light turned on in Search/Turbo mode, for user safety and to protect the flashlight from failure, the TM26 will automatically reduce its output to prevent overheating once it has reached 60 degrees.

Precaution: When the flashlight is hot, do not attempt to cool it by submerging it in liquid. Due to the differences in internal and external air pressure the TM26 may suffer irreparable water damage.

Changing / Charging Batteries

When the power indicator blinks rapidly it means the batteries need to be replaced or recharged. Alternatively if the light becomes dim or unresponsive to adjustment this also indicates batteries need to be replaced or recharged.

Maintenance

Every 6 months, threads should be wiped with a clean cloth followed by a thin coating of silicon-based lubricant.

Warranty Service

All NITECORE® products are warranted for quality. Any defective / malfunctioning NITECORE® product can be repaired free of charge for a period of 60 months (5 years) from the date of purchase. Beyond 60 months (5 years), a limited warranty applies, covering the cost of labor and maintenance, but not the cost of accessories or replacement parts.

The warranty is nullified in all of the following situations:

1. The product(s) is/are broken down, reconstructed and/or modified by unauthorized

parties.

1. The product(s) is/are damaged through improper use.

2. The product(s) is/are damaged by leakage of batteries.

For the latest information on NITECORE® products and services, please contact a local NITECORE® distributor or send an email to [e-mail]

※All images, text and statements specified herein this user manual are for reference purpose only. Should any discrepancy occurs between this manual and information specified on www.nitecore.com, information on our official website shall prevail. Sysmax Industry Co., Ltd. reserves the rights to interpret and amend the content of this document at any time without prior notice.

Please find us on facebook: NITECORE Flashlights

SYSMAX ind.

SYSMAX Industry Co., Ltd.

TEL: [phone]

FAX: [phone]

E-mail: [e-mail]

Web: www.nitecore.com

Address: Rm1401-03, Glorious Tower, 850 East Dongfeng Road, Guangzhou, China 510600

20151015