Question 1

Can a fixed presser foot be adapted to the JUKI 1181N industrial sewing machine?

Accepted Answer

The JUKI 1181N uses a standard attachment system for industrial presser feet that is compatible with several types of alternative presser feet. Yes, a fixed presser foot can be adapted to this machine, provided that it is specifically designed for machines in the JUKI 1181N series or compatible with this standard attachment system.

The machine is compatible with a wide range of specialized presser feet including smooth or standard-toothed presser feet, zipper feet for sewing on closed elements, fine work feet for precise seams, and additional walking feet. Before any adaptation, ensure that the chosen presser foot is expressly compatible with the JUKI 1181N by consulting its technical sheet or contacting the supplier.

Installing a presser foot on the JUKI 1181N is straightforward. Raise the presser foot by operating the control lever located at the back of the machine head, then remove the old foot by unscrewing its attachment or releasing the clamping system. Install the new foot, ensuring it fits correctly into the holder and secure it firmly with the mounting screws.

After the change, check the alignment of the presser foot with the needle plate and perform a sewing test on fabric scraps to ensure the machine operates correctly. Pay particular attention to the fabric feed and thread tension. Remember to adjust the presser foot pressure according to the type of fabric used by turning the pressure regulator (standard setting: 21 mm for moderate pressure). You can increase or decrease this pressure as needed using the knurled adjustment screw (standard value: 16 mm).

If you notice any issues after the adaptation (irregular tension, faulty fabric feed, or operational anomalies), stop immediately and check that the presser foot is compatible and correctly installed. An unsuitable presser foot can damage the machine's mechanism or compromise the quality of the sewing. For specific adaptations or if in doubt about compatibility, consult an authorized JUKI distributor.

Question 2

How to identify a transport cord on a JUKI 1181N industrial sewing machine?

Accepted Answer

To recognize if a cord present on your JUKI 1181N industrial sewing machine is a transport cord, here are some points to check:

1. Location and attachment

The transport cord is generally secured to immobilize certain moving parts of the machine during transport. It is often found around the arm or other moving components and is attached in a way that prevents any movement.

2. Function of the cord

If the cord prevents the normal movement of a part or blocks the mechanism, it is likely that it is a transport cord intended to protect the machine during transport.

3. Appearance of the cord

Transport cords are often sturdy, tied or securely attached, and are not part of the machine's usual operating mechanism.

4. Removal before use

Before starting the machine, it is important to remove this cord to allow the moving parts to function properly.

In summary, a transport cord on the JUKI 1181N is a temporary fixture, securely attached to immobilize the machine during transport, which must be removed before use.

Question 3

How to remove a cord stuck in the arm of the JUKI 1181N industrial sewing machine?

Accepted Answer

If a cord or thread is stuck in the arm of the JUKI 1181N industrial sewing machine, the intervention must be carried out carefully to preserve the integrity of this robust machine designed for sewing thick materials (leather, industrial fabrics). Before any handling, immediately unplug the machine from its power supply (220-240 V) to eliminate all risks of electrocution or injury from moving parts.

Start by carefully examining the area of the arm to precisely identify where and how the cord or thread is stuck. Check especially if the cord is wrapped around moving parts (thread lifting springs, trapezoidal belt), blocked between components, or simply caught between the arm and an adjacent part. This inspection is crucial as it will determine your removal strategy.

If the cord is superficial and easily accessible, attempt a gradual removal by gently and steadily pulling in a smooth motion, without forcing abruptly. If the cord resists or if its anchor point is not visible, you will need to access the internal areas of the arm. On the JUKI 1181N, it is possible to remove the rubber cap located on the surface of the machine's arm to access the internal elements without completely disassembling the inspection window. Refer to the access and adjustment sections of your manual to locate this cap.

Once access is opened if necessary, use delicate tools: small needle-nose pliers, a screwdriver, or a plastic spoon to gently guide the stuck cord. Absolutely avoid sharp tools or rough gestures that could damage fine parts such as the thread lifter springs or adjustment surfaces. Work slowly and methodically to determine the optimal direction of movement.

After complete extraction of the cord, check the proper mechanical functioning without sewing thread or bobbin: manually turn the main wheel for a few turns to ensure that the moving parts (thread lifter, thread guide, drive mechanism) operate without abnormal resistance. Visually inspect the freed areas for any broken thread, damaged spring, or misaligned component.

If the cord remains stuck after your attempts, if you do not have the appropriate tools, or if you detect visible damage, immediately contact an authorized JUKI service center. Industrial machines of this class (power 550 W, weight 50 kg) contain critically adjustable parts whose repairs require specialized expertise and equipment. Improper handling can degrade the alignment of essential elements and compromise the stitching quality on your future projects.

Question 4

How do I adjust the height of the dual feed foot on a JUKI 1181N industrial sewing machine to avoid marking the leather?

Accepted Answer

To properly adjust the height of the dual feed foot on your JUKI 1181N and avoid marking the leather, two elements are essential: the adjustment of the feed dog and the pressure of the presser foot.

Adjustment of the feed dog: The feed dog has been factory-set to extend 1.2 mm above the needle plate. When sewing leather, especially if you notice marks or fraying, you will need to slightly decrease this height. Start by disengaging the machine and locating the feed dog adjustment screw on the arm. Gradually lower the feed dog by about 0.3 to 0.5 mm by slightly loosening the screw, then perform a test on a scrap piece of leather similar to your project material before tightening it permanently.

Reducing the presser foot pressure: Marking on the leather often comes from excessive pressure. Locate the presser foot spring regulator (usually located at the front of the machine, marked with a standard value of 21 mm). To protect your leather, decrease this pressure by turning the regulator about 2 to 3 mm to the left. Then test the material feed: it should remain consistent without the leather showing visible marks from the presser foot.

Complete adjustment procedure: Turn off and unplug the machine before any intervention. Start by reducing the presser foot pressure by about 3 mm from the standard setting (21 mm), then slightly lower the feed dog. Perform gradual sewing tests on scraps of leather to precisely adjust these two parameters together. The goal is to maintain a consistent feed of the leather while minimizing marks. Remember that when increasing or decreasing the height of the feed dog, you must ensure that the feed dog does not come into contact with the needle plate.

Once these satisfactory adjustments are made, firmly tighten all the adjustment screws and perform a final test before starting your sewing work. These adjustments will help protect your leather while ensuring a good feed of the material during your projects.

User manual JUKI Industrial sewing machine : user manuals and guides in PDF

Models JUKI Industrial sewing machine most viewed

Other categories JUKI

Recent questions about Industrial sewing machine JUKI