Q: What is the spare part number for the water leak sensor for the WT100?

The leak sensor of the Zepter Aqueena Pro WT100 does not have a spare part number listed in the official documentation provided with the device. The manual details the operation of the sensor (audible and visual alert in case of leak detection) and the steps to reset it after an incident, but does not offer this component for separate sale. The available spare parts for this model are limited to the filters: PP 5 micron filter (WT-100-72) Charcoal tablet filter (WT-100-73) PP 1 micron filter (WT-100-74) Coconut filter (WT-100-75) OI membrane (WT-100-15) To obtain the leak sensor or check its availability, please contact Zepter customer service directly via your warranty card, as this component is not offered in the standard spare parts catalog.

Q: What are the replacement part numbers for the Aqueena Pro WT100?

Here are the official Zepter spare part numbers for your Aqueena Pro WT100 : Replacement Filters WT-100-72 : PP Filter 5 microns (lifetime: 6 months) WT-100-73 : Charcoal Tablet Filter (6 months) WT-100-74 : PP Filter 1 micron (6 months) WT-100-75 : Coconut Filter (12 months) Membrane WT-100-15 : OI Membrane at 0.0001 micron (12 months) Important: To maintain your 2-year warranty and ensure the proper functioning of your purifier, use only original Zepter spare parts. Adhering to the recommended replacement intervals (6 months for PP and charcoal filters, 12 months for the coconut filter and membrane) ensures optimal purified water.

Question 1

What is the spare part number for the water leak sensor for the WT100?

Accepted Answer

The leak sensor of the Zepter Aqueena Pro WT100 does not have a spare part number listed in the official documentation provided with the device. The manual details the operation of the sensor (audible and visual alert in case of leak detection) and the steps to reset it after an incident, but does not offer this component for separate sale.

The available spare parts for this model are limited to the filters:

PP 5 micron filter (WT-100-72)
Charcoal tablet filter (WT-100-73)
PP 1 micron filter (WT-100-74)
Coconut filter (WT-100-75)
OI membrane (WT-100-15)

To obtain the leak sensor or check its availability, please contact Zepter customer service directly via your warranty card, as this component is not offered in the standard spare parts catalog.

Question 2

What are the replacement part numbers for the Aqueena Pro WT100?

Accepted Answer

Here are the official Zepter spare part numbers for your Aqueena Pro WT100:

Replacement Filters

WT-100-72: PP Filter 5 microns (lifetime: 6 months)
WT-100-73: Charcoal Tablet Filter (6 months)
WT-100-74: PP Filter 1 micron (6 months)
WT-100-75: Coconut Filter (12 months)

Membrane

WT-100-15: OI Membrane at 0.0001 micron (12 months)

Important: To maintain your 2-year warranty and ensure the proper functioning of your purifier, use only original Zepter spare parts. Adhering to the recommended replacement intervals (6 months for PP and charcoal filters, 12 months for the coconut filter and membrane) ensures optimal purified water.

Question 3

Is there a code or numerical index for the leak sensor?

Accepted Answer

No, there is no code or numerical index for the leak sensor of the Zepter Aqueena Pro WT100. This sensor does not emit any specific error code, unlike other alert systems. It communicates detections through direct signaling only.

When the sensor detects a water leak in the device, it triggers a double alert:

Visual signal: all icons on the screen flash simultaneously ("On", "Water Source", "Standby", and "Rinse" icons)
Audible signal: an audible alarm sounds

This double alert indicates that a leak has occurred somewhere in the system: connections, tanks, piping, or internal seals. It is important to act quickly as water can damage the internal components of the device and your installation.

If you receive this alert, proceed in this order:

Immediately turn off the device
Close the main water supply valve
Remove the top cover and locate the source of the leak
Repair or tighten the faulty connections
Completely drain the water that has leaked by removing the rubber plug located at the bottom of the casing
Allow the sensor and all internal components to dry completely
Restart the device once everything is dry

The leak sensor does not need to be manually reset: as soon as it detects that the water is gone and everything is dry, it automatically resets and the icons will stop flashing.

User manual Zepter Water purifier : user manuals and guides in PDF

Models Zepter Water purifier most viewed

Other categories Zepter

Recent questions about Water purifier Zepter