Q: What type of battery does the ZEISS Secacam 7 use?

The ZEISS Secacam 7 uses 8 LR6 (AA) batteries - either alkaline batteries or compatible rechargeable LR6 batteries. Important: Do not mix batteries and rechargeable batteries. If you use one type, use that same type for all 8 slots. Battery Life and Consumption With 8 new LR6 batteries, you have a battery life of approximately 300 photos. Power consumption increases significantly in video mode, especially for nighttime recordings. External Power Supply You can also power the device via an external power supply of at least 12V/2A. The connector is a hollow plug with an outer diameter of 4mm, an inner diameter of 1.7mm, with the positive pole inside and the negative pole outside. Before any use, do not forget to remove the circuit breaker from the battery compartment.

Q: How to install the batteries in the ZEISS Secacam 7?

The ZEISS Secacam 7 uses 8 AA (LR6) batteries which are installed according to the following process: Turn off the camera. Unlock the shutter clip located on the right side and open the back of the device. Press the EJECT button located at the bottom right. The battery compartment extends about 2 cm and can be completely removed by pulling it down. Install the 8 batteries respecting the correct polarity , which is indicated inside the compartment. Reinsert the compartment into the device until it clicks into place. Before using the device, be sure to remove the safety switch from the battery compartment. Important: You can use alkaline batteries or rechargeable batteries, but never mix the two types. For night photography, replace all batteries with fully charged ones. A set of 8 batteries allows for approximately 300 photos.

Question 1

What type of battery does the ZEISS Secacam 7 use?

Accepted Answer

The ZEISS Secacam 7 uses 8 LR6 (AA) batteries - either alkaline batteries or compatible rechargeable LR6 batteries.

Important: Do not mix batteries and rechargeable batteries. If you use one type, use that same type for all 8 slots.

Battery Life and Consumption

With 8 new LR6 batteries, you have a battery life of approximately 300 photos. Power consumption increases significantly in video mode, especially for nighttime recordings.

External Power Supply

You can also power the device via an external power supply of at least 12V/2A. The connector is a hollow plug with an outer diameter of 4mm, an inner diameter of 1.7mm, with the positive pole inside and the negative pole outside.

Before any use, do not forget to remove the circuit breaker from the battery compartment.

Question 2

How to install the batteries in the ZEISS Secacam 7?

Accepted Answer

The ZEISS Secacam 7 uses 8 AA (LR6) batteries which are installed according to the following process:

Turn off the camera.
Unlock the shutter clip located on the right side and open the back of the device.
Press the EJECT button located at the bottom right. The battery compartment extends about 2 cm and can be completely removed by pulling it down.
Install the 8 batteries respecting the correct polarity, which is indicated inside the compartment.
Reinsert the compartment into the device until it clicks into place.
Before using the device, be sure to remove the safety switch from the battery compartment.

Important: You can use alkaline batteries or rechargeable batteries, but never mix the two types. For night photography, replace all batteries with fully charged ones. A set of 8 batteries allows for approximately 300 photos.

Question 3

How to check the firmware version number on the ZEISS Secacam 7?

Accepted Answer

To check the firmware version number of your ZEISS Secacam 7, follow these steps:

Set the switch on the housing to SETUP: the LCD screen will light up after about 2 seconds and display the preview mode
Press the MENU button to open the camera's main menu
Use the up and down arrows to navigate to the Firmware-Version option (or Version firmware depending on the language)
Press the OK button to access this option
The currently installed version number will then be displayed on the screen
Press MENU to exit and return to the main menu

The firmware of your ZEISS Secacam 7 is regularly improved and updated by Zeiss. To check if a newer version is available for your model, visit www.zeiss.com/cop/downloads. You can download new firmwares there if necessary.

Before performing a firmware update, ensure that the eight AA (LR6) batteries of your camera are fully charged or replaced with new batteries. A power interruption during the update could permanently damage your device. You can also use the external power supply 12 V - 2 A to secure the update.

User manual ZEISS Camera : user manuals and guides in PDF

Models ZEISS Camera most viewed

Other categories ZEISS

Recent questions about Camera ZEISS