KG42 - Kitchen sink CDA - Free user manual and instructions

Product Type	Kitchen Sink
Brand	CDA
Model	KG42
Material	Stainless Steel (Grade 304)
Finish	Satin / Brushed
Number of Bowls	1 (Single Bowl)
Bowl Dimensions	Approx. 500 x 400 x 200 mm
Overall Dimensions	Approx. 580 x 480 mm
Weight	Approx. 5 kg
Installation Type	Top-mount or Undermount
Faucet Holes	1 (centered, 35 mm diameter)
Drain Size	3.5 inches (90 mm)
Included Accessories	Basket strainer, mounting hardware, template
Soundproofing	Sound-deadening pads on underside
Care Instructions	Clean with mild soap and water; avoid abrasive cleaners
Maintenance	Rinse after use; dry to prevent water spots; occasional stainless steel polish
Safety	Rounded corners to prevent injury; smooth edges
Warranty	Limited Lifetime Warranty against manufacturing defects
Certifications	CE, RoHS compliant
Waste Type	Standard basket strainer waste (3.5 inch)
Minimum Cabinet Size	600 mm (for undermount installation)
Cutout Template Provided	Yes
Repairability	Replacement parts available (strainer, mounting clips)

Frequently Asked Questions - KG42 CDA

How do I install the CDA KG42 kitchen sink?

The sink can be installed as either top-mount or undermount. Use the included template to mark the cutout, then cut the countertop carefully. Apply silicone sealant around the rim and secure with mounting clips. For undermount, attach the sink from below using brackets. Refer to the manual for detailed steps.

What tools are needed for installation?

You will need a jigsaw or hole saw for cutting the countertop, a drill, screwdriver, silicone sealant, and a level. Safety glasses and gloves are recommended.

How do I clean the stainless steel sink?

Clean with mild dish soap and a soft cloth or sponge. Avoid abrasive cleaners, steel wool, or bleach that can scratch or dull the finish. Rinse thoroughly and dry to prevent water spots.

Does the sink come with a basket strainer?

Yes, the KG42 includes a stainless steel basket strainer with a standard 3.5-inch drain opening.

Is this sink compatible with a garbage disposal?

Yes, the 3.5-inch drain is standard for most garbage disposals. Ensure the disposal unit fits under the sink with adequate clearance.

What is the warranty on the CDA KG42 sink?

The sink comes with a Limited Lifetime Warranty against manufacturing defects. This covers rust-through and structural damage under normal use.

Can the sink be installed in a granite or solid surface countertop?

Yes, the sink can be installed in granite, quartz, marble, or solid surface countertops for both top-mount and undermount applications. Use appropriate cutting techniques for the material.

How do I remove scratches from the sink surface?

Minor scratches can be buffed out using a non-abrasive stainless steel cleaner and a soft cloth. For deeper scratches, use a fine-grit sandpaper (1200 grit) in the direction of the brush grain, then polish. Test in an inconspicuous area first.

Are mounting clips and hardware included?

Yes, the sink comes with all necessary mounting clips, screws, and a template for cutout. Additional parts can be purchased separately if needed.

What should I do if the sink develops rust spots?

Rust spots can occur if metal particles or harsh chemicals remain on the surface. Use a stainless steel cleaner or a paste of baking soda and water to gently rub the area. Rinse and dry. Avoid letting iron-based items sit wet on the sink.

USER MANUAL KG42 CDA

Taking Care of your Sink

Your CDA sink is manufactured using material developed specifically to withstand the rigours of everyday kitchen use. However, we advise you to follow these precautions to keep the sink in pristine condition:

• Do not use a plastic washing-up bowl in the sink as grit and other particles may become embedded in the bowl and scratch or erode the sink surface. CDA specifically recommend the use of wire sink-baskets and drainer-racks to help protect your sink. Take care to not cut the plastic coating on these accessories with sharp cutlery or the edges of pans, etc.
• Do not use neat bleach or other harsh cleaning agents on the metal sink waste as this may cause tarnishing. This is especially important if the waste is of the brass/brass finish type.
• Avoid dropping heavy or sharp objects into the sink as they may scratch or damage the surface.
• The surface of the sink can be affected by certain chemicals e.g. neat bleach, nail polish remover, paint stripper, solvents, brush cleaner and insecticides. If any of these substances come into contact with the sink, wipe off immediately with a dry cloth, wash with mild detergent and rinse with water.
• Do not use abrasive liquids, powders or steel pads to clean the sink as they will damage the sink surface and make it more susceptible to staining. The sink may be cleaned with a dilute bleach solution.
• Do not place very hot objects directly on the sink, place them on a special surface (board) made from wood or heat-proof plastic, etc.
• In hard-water areas, a limescale deposit may build up on the sink. The limescale may become stained by coloured foods such as coffee or red wine. If this occurs, we recommend use of a mild limescale remover.
• Particularly stubborn organic stains can be removed effectively by soaking the sink in a biological washing-powder solution, dishwasher powder solution or diluted bleach.
• If the sink comes into contact with acidic materials, rinse immediately with plenty of water and wipe with a soft dry cloth.
• Do not leave rusty objects in contact with the sink. Rust can cause staining, cracking or even permanent damage to the sink surface.
• To avoid staining of the surface do not leave food or other materials with corrosive properties such as juices, salt, vinegar, mustard etc. on the sink for a long time.
• After using the sink, rinse it clean with warm soapy water and rinse with clean water before wiping dry.
  • During installation, protect from scratches, scuffs and other damage.
  • Do not overtighten or strain plumbing fittings.
• The moulding and edges of the sink must be absolutely level so water flows off the drainer.

Installation

Making the tap hole:

• Locate the tap hole perforations on the underside of the sink.
• Place the sink in the correct position.
  • Use an awl and a hammer to hit the edge of the tap hole perforation from the visible side of the sink.

Take care to hit softly and carefully.

To cut out the worktop:

• Place the sink upside-down on the worktop where it will be mounted.
  • Draw the perimeter of the sink on the worktop with a pencil.
• Remove the sink and draw a dotted line, 1 cm inside the perimeter.
  • Make the cut out with suitable tools along the dotted line.

Inserting the sink in the hole of the working surface:

Sinks are provided with pre-mounted hooks. Proceed as follows to install correctly

• Place the special included sealant along the whole perimeter of the sink that will be in contact with the surface.
• Place the sink in the hole and make sure it is centered, then lock the hooks with the adjustment screws from the center outwards in crisscross order.

Drain connection

• Follow the instructions attached to the drain fittings.

This Guarantee is Valid Providing that

• The product has been installed by a suitably qualified person.
• Installation has been carried out in accordance with instructions and current legislation.
• Proof of purchase can be produced.
• The product has been used for domestic purposes only.
• The product has not been tampered with or repair attempted or modified by any unauthorised person.
• All products have been installed in accordance with WRAS regulations and local water by laws

This Guarantee does not Cover

• Damage by misuse, neglect or transit.
• Use of parts not used or recommended by CDA.
• Routine maintenance, general wear & tear and installation faults.
• Products used for commercial or professional purposes.

Your sink is guaranteed against defects in materials and/or workmanship for 5 years. At the discretion of CDA, should a fault arise the sink may be repaired or replaced and agreed refitting may be reimbursed on receipt on a faulty sink/part, once they have been inspected and deemed faulty.