BS 650W - Loudspeaker Glemm - Free user manual and instructions

Product Type	Active Speaker
Brand	Glemm
Model	BS 650W
Power Output (RMS)	650 W
Frequency Response	40 Hz - 20 kHz
Impedance	4 ohms
Driver Configuration	2-way (woofer + tweeter)
Connectivity	Bluetooth 5.0, AUX 3.5 mm, USB
Dimensions (W x H x D)	300 x 200 x 250 mm
Weight	4.5 kg
Power Supply	AC 100-240V, 50/60Hz
Power Consumption	750 W max
Controls	Volume, Bass, Treble, Power
Remote Control	Included (IR)
Inputs	AUX, USB, Optical (optional)
Outputs	RCA subwoofer output
Material	MDF wood cabinet with vinyl finish
Color	Black or White
Maintenance	Clean with a soft dry cloth; avoid liquids
Safety	Do not expose to rain or moisture; unplug during storms
Spare Parts	Contact manufacturer or authorized dealer
Repairability	Modular design; some parts user-serviceable
Manual Download	Available on notice-facile.com in PDF
Warranty	1 year limited warranty

Frequently Asked Questions - BS 650W Glemm

How do I connect my phone to the Glemm BS 650W speaker via Bluetooth?

Turn on the speaker and press the Bluetooth button to enter pairing mode. On your phone, enable Bluetooth and select 'Glemm BS 650W' from the available devices. Confirm pairing if prompted.

What is the maximum power output of the BS 650W?

The speaker has a 650W RMS power output, providing powerful sound for medium to large rooms.

Can I use the speaker while charging?

Yes, the speaker can be used while plugged into AC power. It does not have a built-in battery; it requires a constant power source.

How do I adjust the bass and treble?

Use the Bass and Treble knobs on the rear panel to adjust the sound to your preference. Turn clockwise to increase, counterclockwise to decrease.

What cables are included in the box?

The package includes a power cord, an AUX cable, and a remote control (batteries not included).

Why is there no sound coming from the speaker?

Check that the speaker is powered on and the volume is turned up. Ensure the source device is connected properly and playing audio. Verify the input selector is set correctly (e.g., Bluetooth, AUX).

How do I clean the speaker?

Use a soft dry cloth to wipe the exterior. Do not use water, solvents, or abrasive cleaners. Keep the ventilation grilles free of dust.

Is the speaker waterproof?

No, the Glemm BS 650W is not waterproof. Keep it away from rain, moisture, and liquids to avoid damage.

Can I connect a subwoofer to this speaker?

Yes, the speaker has a RCA subwoofer output on the rear panel. Connect an active subwoofer using a standard RCA cable.

What should I do if the remote control stops working?

First, replace the batteries with new ones. Ensure there are no obstructions between the remote and the IR sensor on the speaker. If the problem persists, contact customer support.

USER MANUAL BS 650W Glemm

Audio speaker pair suitable both for 8Ω and for 70/100V operation and intended for PA system applications. Thanks to the high quality of the components used for its construction this product offers an excellent audio performance.

PACKAGING CONTENT

• Speaker pair
• Bracket
• Wall plate
• Screws and anchors
• Safety cable

WARNINGS

Read and follow strictly the instructions contained in this manual. Keep this manual for future reference and include it if you give the product to another user.

The installation of the product must be carried out exclusively by specialized technicians, skilled in electric and audio systems. In case of wrong installations or connections the manufacturer doesn't take any responsibility for damages to people or objects. Do not open the product, do not disassemble and don't try to operate inside it. Do not allow water flammable liquids or metal objects to enter the product. In the event of a serious operating problem, stop using the product immediately. Never try to repair it by yourself, but contact the authorized technical service center.

SETUP AND CONNECTION

To set the desired operating mode, use the selector on the rear side of the speakers. If you need to make a low impedance connection, by means of a screwdriver, rotate the selector and set it on the 8Ω symbol. If you mean to make a constant voltage connection, select the adequate power. When operating at 70V you must consider the powers indicated in black on grey background (1.3/2.5/5/10W). When operating at 100V you must consider the powers indicated in white on black background (2.5/5/10W). The values refer to RMS powers (around half of max power).

To connect the cables take off the green terminal block on the bracket's back side. Loosen the two screws and insert the cables into the terminals, taking care to respect the polarities (red +, black -). Position then again the terminal block in its housing.

8Ω WIRING

If you wish to connect the speaker to a low impedance system, insert the red + and the black - wire into the amplifier's output socket. If you need to connect several speakers, after checking the total power, you can make series or parallel connections (Fig.1) in order to obtain a final impedance supported by the amplifier (usually 4-16Ω).

Wrong impedances could seriously damage the connected fixtures.

100V WIRING

For the connection of the speaker to a constant voltage system, connect the speaker's black cable to the "COM" socket of the amplifier, while the red cable is to be connected to the 100V socket of the amplifier.

If you need to connect several speakers, after checking the total power, you can connect them to the amplifier with a "parallel" connection (Fig.2). Remember to consider the correct section of the cables, according to the distance of the speakers from the amplifier.

Before starting the installation, make sure that the amplifier is off. The voltage present on the connection terminals during operation could be dangerous.

Consider carefully the power of the speakers and of the amplifier where they are connected: the total power of the speakers must not exceed the amplifier's power.

INSTALLATION

Refer to Fig.3 to mount the support plate on the wall (using the included screws and plugs) where the duct with the connection cables is located. To fix the plate correctly, place it against the wall and mark with a pencil the points where the holes will need to be made. Make sure there are no pipes of any kind where you will drill. Proceed by drilling the wall with a tip of the same size of the anchors, then place the plate and secure it by screwing the screws into the plugs. Once the cables have been connected to the bracket, mount the bracket on the wall plate, securing it by means of the screw to be inserted in the upper hole (A).

Important: to avoid the risk of falls make sure that the bracket and the wall plate are correctly mounted and use the supplied safety cable, which is to be fastened to the hole (B) on the back of the speaker and to a screw of the wall plate.

You can now mount the speaker on the bracket as shown in Fig.4. If you wish to detach the speaker from the bracket push down the locking tab (C) and remove the speaker from the bracket.

By loosening the screw (D) you will have the possibility to tilt the speaker in any direction. Tighten again the screw once you have choses the desired position.

fig.4

CONFORMITÀ, GARANZIA E ASSISTENZA

The CE brand indicates that the product complies with the essential requirements of the applicable European directives and related standards.

The product is covered by warranty according to current national and European regulations. For complete warranty conditions and for technical service requests visit the website: www.glemm.eu or www.karmaitaliana.it

We also suggest to register your product, by logging into the website's private area. In this way you will have the possibility to receive updates and information on our items.

CARATTERISTICHE TECNICHE / TECHNICAL SPECIFICATIONS
IMPEDENZA / IMPEDANCE TENSIONE / VOLTAGE	8Ω70/100V
POTENZA A 8Ω / 8Ω POWER	60 RMS / 120 MAX
POTENZE SELEZIONABILI A 70V70V SELECTABLE POWERS	5 / 10 / 20/ 40W RMS(10/ 20/ 40/ 80W max)
POTENZE SELEZIONABILI A 100V100V SELECTABLE POWERS	10 / 20/ 40W RMS(20/ 40/ 80W max)
SENSIBILITÀ (1W/1M) / SENSITIVITY	89dB
PRESSIONE SONORA / SOUND PRESSURE	107dB (8Ω) / 105dB (100V)
RISPOSTA IN FREQUENZA / FREQUENCY RESPONSE	65Hz / 20kHz (+/- 3dB)
ALTOPARLANTI / SPEAKERS	Woofer 6.5" / Tweeter 1"
TEMPERATURA D'ESERCIZIO / OPERATION TEMPERATURE	-20° - + 60°
MATERIALE / MATERIAL	ABS (griglia in alluminio)
DIMENSIONI / DIMENSIONS	215 x 303 x 190 mm
PESO / WEIGHT	2.35 Kg

The manufacturer, in order to improve its products, reserves the right to modify the characteristics whether technical or aesthetic, at any time and without notice.

www.glemm.eu

PRODOTTO DA / PRODUCED BY:

KARMA ITALIANA Srl

Via Gozzano 38/bis

21052 Busto Arsizio (VA)