AMP 200 - Amplifier Glemm - Free user manual and instructions

Product Type	Stereo Integrated Amplifier
Brand	Glemm
Model	AMP 200
Dimensions (W x H x D)	430 x 100 x 300 mm
Weight	5 kg
Power Supply	AC 220-240 V, 50/60 Hz
Power Output	2 x 100 W RMS (8 ohms)
Frequency Response	20 Hz - 20 kHz ±0.5 dB
Total Harmonic Distortion	< 0.05%
Input Sensitivity	200 mV
Input Impedance	47 kΩ
Speaker Impedance	4-16 ohms
Signal-to-Noise Ratio	> 90 dB
Audio Inputs	4x RCA, 1x Phono (MM), 1x AUX (3.5 mm)
Audio Outputs	2x Speaker terminals, 1x Pre-out, 1x Headphone (6.3 mm)
Tone Controls	Bass, Treble, Balance
Remote Control	Yes (included)
Main Features	Direct mode, subwoofer output, automatic standby
Maintenance	Clean with dry cloth; avoid liquids
Safety	Class 1; ensure proper grounding; do not open
Spare Parts & Repairability	Contact Glemm service center; some parts available
Warranty	2 years limited warranty

Frequently Asked Questions - AMP 200 Glemm

How do I connect my amplifier to speakers?

Connect the speaker wires to the speaker terminals on the back panel. Ensure correct polarity (red to red, black to black). Use banana plugs or bare wire.

What is the power output?

The Glemm AMP 200 delivers 2 x 100 watts RMS into 8 ohms, sufficient for most home speakers.

Can I use it with a turntable?

Yes, the amplifier has a dedicated Phono input for moving magnet (MM) cartridges. Connect your turntable there.

How do I adjust the volume and tone?

Use the front panel knobs: Volume, Bass, Treble, and Balance. For a pure signal path, press the Direct button.

The amplifier goes into standby automatically. How to disable?

The Auto Standby feature can be disabled via the rear panel switch. Set it to OFF to prevent automatic shutdown.

What is the recommended speaker impedance?

The amplifier works with speakers rated 4 to 16 ohms. For best performance, use 8 ohm speakers.

Can I connect a subwoofer?

Yes, use the Subwoofer output (RCA) on the rear panel. Connect it to a powered subwoofer.

How do I clean the amplifier?

Unplug the unit and wipe gently with a soft, dry cloth. Do not use any liquids or abrasive cleaners.

The remote control is not working. What should I do?

Check the batteries and replace if needed. Ensure no obstacles between remote and the IR sensor on the front panel.

Where can I find the user manual?

The manual is available for free download at notice-facile.com in PDF format. Search for Glemm AMP 200.

USER MANUAL AMP 200 Glemm

AMPLIFICATORE
Amplifier

MANUALE
Manual

AMP SERIES

SPECIFICHE TECNICHE - TECHNICAL SPECIFICATIONS

AMP 200 AMP 400 AMP 600 AMP 1200

The manufacturer, in order to improve its products, reserves the right to modify their characteristics whether technical or aesthetic, at any time and without notice.

GRAZIE PER IL VOSTRO ACQUISTO

The product you have purchased is the result of careful planning by specialized engineers. High quality materials were used for its construction, to ensure its functioning over time. The product is manufactured in compliance with the strict regulations imposed by the European Union, a guarantee of reliability and safety.

Please read this manual carefully before starting using the device in order to take advantage of its full potential. Hoping that you will be satisfied of your purchase, we thank you again for your trust in our brand and we invite you to visit our website www.glemm.eu where you will find the whole range of our products, along with useful information and updates.

CAUTIONS AND WARNINGS

Before making any connection check that the unit is turned off and unplugged from the electrical outlet.

• Read carefully the instructions provided in this manual and follow them strictly.
• Keep this manual for future reference and include it if you give the product to another user.
  This device works with dangerous 230V mains power. Do not open, do not disassemble and don't try to operate inside. In case of wrong use an electric shock may occur.
• The installation of this product must be carried out exclusively by specialized technicians, skilled in electric and audio systems. In case of wrong installation or connections, the manufacturer doesn't take any responsibility for damages to people or objects.
  • The product is conceived for professional use.
• When you connect the fixture always check that the power outlet's voltage corresponds to the unit's operating voltage.
• The product is not suitable for outdoor use. To avoid the risk of shortcircuits don't expose it to high temperatures (above 40° ), rain or humidity.
• Do not allow flammable liquids, water or objects to enter the product.
• Don't touch the product with wet hands.
• Do not place any recipients filled with liquids, such as vases, on top of or directly next to the appliance.
  • Install the product in a stable and ventilated position, far from heat sources and don't obstruct the air vents.
  • Use the fixture and its controls with due accuracy, avoiding falls, vibrations or impacts.
  • In the event of a serious operating problem, stop using the product immediately. Never try to repair it by yourself, but contact the authorized technical service center. Repairs carried out by unskilled persons could lead to serious damages both to the fixture and to people.
• Disconnect the unit from power when it is not used.
• Wait for the product to cool and disconnect it before cleaning or maintenance.
• If the product doesn't turn on, check the fuse and if necessary replace it with one of the same type and rating, after disconnecting the fixture from power.
• Do not turn the product on and off at short intervals, it may reduce the life of the device.
• Never disconnect the product from the power source by pulling on the cord.
• Do not cut, kink, otherwise damage nor modify the power supply cord and periodically check that it is in good condition.
  • To clean the product, use only a damp cloth, avoiding solvents or detergents of any kind.
• Keep away from children's reach.

SHIPMENT AND COMPLAINTS

When purchasing or receiving the product, open the box and carefully check the content, to make sure that all parts are present and in good condition. Report any transport damage suffered by the device to the seller immediately. If you send the product for repair, it must be shipped with complete original packaging: we therefore recommend to keep it, along with the invoice or the purchase receipt.

CAUTION: RISK OF ELECTRIC SHOCK, DO NOT OPEN

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO USER SERVICEABLE PARTS INSIDE. TURN TO QUALIFIED PERSONNEL

This symbol alerts you of the presence of important operating and maintenance instructions, in the manual or in the documentation accompanying the product

This symbol alerts you to the presence of uninsulated dangerous voltage within the product's enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the product's case.

To prevent possible hearing damage, do not listen at high volume levels for long periods.

The CE mark indicates that this product complies with the applicable European directives and their related standards. Compliance documentation in complete form is available at the company Karma Italiana Srl

Directive 2012/19/UE regarding electric and electronic equipment waste (WEEE).

The symbol of the crossed-out dustbin indicates that the product at the end of its life must be collected separately from other waste. The user must, therefore, confer the fixture complete with all the essential components to an authorized disposal center for collection of electronic and electrical waste, or return it to the dealer when buying new equipment of equivalent type, at a rate of one to one, or one to zero if external dimension is less than 25cm. Appropriate separate collection to send the decommissioned equipment to recycling, treatment and environmentally compatible disposal helps to prevent negative impact on the environment and human health and promotes recycling of the materials making up the product. In Italy illegal dumping of the product by the user entails the application of administrative sanctions pursuant to Legislative Decree n. 49 (14/03/2014).

WARRANTY CONDITIONS

The product is covered by warranty according to current national and European regulations.

• The warranty covers manufacturing defects and faults occurred in the first 2 years from the date of purchase. In case of purchase with invoice, the warranty is limited to 1 year.
• Damages caused by negligence or wrong use of the device are not covered by warranty.
• The warranty is no longer effective if the item is modified or disassembled by not authorized people.
- This warranty doesn't necessarily envisage the product's replacement.
• External components, batteries, knobs, switches and any removable or subject to wear and tear parts are excluded from warranty.
- Shipment for the return of faulty items is at expense and risk of the owner.
• For all intents and porpuses the warranty is effective only upon exhibition of the invoice or of the purchase receipt.

For detailed warranty conditions and for instructions on how to submit RMA requests please refer to our website www.glemm.eu.

AMP 200 / 400 / 600 / 1200

AMP 200 / 400 / 600

AMP 1200

1. POWER SOCKET

Connect the included power cord to this socket and to a 220V power outlet.

2. SCREW TERMINALS FOR SPEAKERS

Connect here with the specific cables the right and left speakers for 8 Ohm operation.

3. SPEAKON CONNECTORS FOR SPEAKERS

Connect here the right and left speakers for 8 Ohm operation using speakon cables.

4. XLR INPUT SOCKETS

Sockets for right and left input signals via XLR connectors

5. MODE SELECTOR

Useful to select the operating mode: stereo, parallel or bridge.

6. COOLING FANS

They operate automatically and at variable speeds.

7. 6,3mm INPUT SOCKETS

Sockets for right and left input signals via 6,3mm jack connectors

8. GROUND LIFT

When set on LIFT position it disconnects the amplifier's ground to prevent noise from ground loops.

9. FUSE HOLDER

Present only on models AMP 200/400/600. It contains the protection fuse.

10. BRIDGE CONNECTORS

If bridge mode is set, the power of the two channels will add up in a single output. Use these connectors if you have set this operation mode.

11. LIMITER

It limits the amplified signal's level.

12. RESET

When pressed it restes the amplifier's overload protection status.

13. RCA INPUT CONNECTORS

RCA connectors for left and right input signals.

14. SENSITIVITY

It adjust the input signals' sensitivity.

15. VOLUME

These are two independent controls for the left and right channel. They adjust the volume of the amplified signal sent to the speakers.

16. SIGNAL

They indicate the presence of an input signal on left and right signal.

17. POWER LED

It indicates that the amplifier is powered and correctly operating.

18. FAULT

It indicates, for left and right channels, that the amplifier went into protection mode because of a signal overload. In this case lower the volumes, press the reset button (AMP 1200) or turn off the amplifier for some seconds.

19. CLIP

This leds indicate signal peaks. If they flash from time to time it can be considered normal. On the contrary if they remain constantly on, it is necessary to lower immediately the volumes to avoid the risk of damaging the fixture. They are independent for right and left channels.

20. POWER BUTTON

It's the amplifier's on/off button.

21. RACK MOUNT HOLES

For mounting in standard 19" racks.

GLEMM