PAA 120DB - Receiver Glemm - Free user manual and instructions
Find the device manual for free PAA 120DB Glemm in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Stereo Receiver |
| Brand | Glemm |
| Model | PAA 120DB |
| Amplifier Output | 120 W per channel (RMS) |
| Frequency Range | 20 Hz - 20 kHz |
| Signal-to-Noise Ratio | 90 dB |
| Input Impedance | 47 kOhm |
| Supported Radio Bands | FM, AM |
| Connectivity | RCA inputs, speaker outputs, headphone jack |
| Number of Audio Inputs | 4 (CD, AUX, TAPE, PHONO) |
| Number of Speaker Outputs | 2 pairs (A/B switching) |
| Power Supply | 230 V AC, 50 Hz |
| Power Consumption | 250 W |
| Standby Power Consumption | < 0.5 W |
| Dimensions (W x H x D) | 430 x 150 x 360 mm |
| Weight | 8 kg |
| Remote Control | Included |
| Display Type | LED FM frequency display |
| Color | Black |
| Cooling Method | Natural convection |
| Operating Temperature | 0°C - 40°C |
Frequently Asked Questions - PAA 120DB Glemm
How do I connect speakers to the PAA 120DB?
Connect the speaker wires to the spring-loaded terminals on the back panel. Ensure the impedance of each speaker is at least 8 ohms and match the positive and negative terminals correctly. You can use the A/B switch to select between two speaker pairs.
Can I connect a turntable to this receiver?
Yes, the PAA 120DB has a dedicated PHONO input for turntables with a moving magnet cartridge. Make sure the turntable has a ground wire connected to the GND terminal to avoid hum.
How do I switch between radio and auxiliary input?
Press the Source button on the front panel or remote control repeatedly to cycle through the available inputs: FM, AM, CD, AUX, TAPE, PHONO. The selected input is shown on the display.
What is the maximum power output of the PAA 120DB?
The receiver delivers 120 watts RMS per channel at 8 ohms, with a total harmonic distortion of under 0.1%. This allows it to drive most home speakers efficiently.
How should I clean and maintain the receiver?
Unplug the device and wipe the exterior with a soft dry cloth. Avoid using liquid cleaners or sprays. Periodically check the ventilation slots and remove dust to prevent overheating.
Is a remote control included with the PAA 120DB?
Yes, a remote control is included in the box. It allows you to adjust volume, switch inputs, and control the tuner from a distance. Insert two AAA batteries (not included) to use it.
How do I set up the FM antenna?
Connect the supplied FM wire antenna to the FM antenna terminal. Extend it fully and position it for the best reception. For AM, connect the loop antenna and rotate it to minimize interference.
What safety precautions should I follow?
Place the receiver on a stable, flat surface with adequate ventilation. Do not block the cooling vents. Avoid exposure to moisture, heat, and direct sunlight. Unplug the unit during thunderstorms or when not in use for extended periods.
Can I connect a subwoofer to this receiver?
The PAA 120DB does not have a dedicated subwoofer output. However, you can connect a powered subwoofer using a RCA splitter from the pre-out or tape monitor connections, if available. Consult your subwoofer manual for options.
How do I reset the receiver to factory settings?
While the unit is on, press and hold the Reset button on the rear panel (if available) for 3 seconds. Alternatively, unplug the receiver for 5 minutes and then plug it back in to clear temporary settings.
User questions about PAA 120DB Glemm
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual PAA 120DB - Glemm and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. PAA 120DB by Glemm.
USER MANUAL PAA 120DB Glemm
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Glemm
Model : PAA 120DB
Category : Receiver