Silent 5622 - Heating Lasko - Free user manual and instructions

Product Type	Electric fan heater (supplemental heat)
Model	Silent 5622
Brand	Lasko
Power Source	120 V AC, 60 Hz
Power Consumption	1500 Watts (High) / 750 Watts (Low, inferred from Heat(1) and Heat(2) but manual only mentions Heat(1); likely two heat settings)
Heating Element	Not specified (likely ceramic or coil)
Thermostat	Automatic temperature control with adjustable set point
Timer	1 to 8 hours auto-off
Display	Digital LED, shows room temperature in °F or °C
Safety Features	Tip-over switch, thermal overload protector, cool-touch housing (inferred)
Placement	Floor use only, stable level surface
Clearance	3 ft (0.9 m) from front, 1 ft (0.3 m) from sides and rear
Cleaning	Vacuum with brush attachment every two weeks; soft cloth for body
Certification	FCC Class B, ETL/UL listed (inferred)
Warranty	3 years limited (USA, territories, Canada only)
Dimensions	Not specified in manual; typical similar model: approx 26 x 6 x 6 inches
Weight	Not specified; estimate 6-8 lbs

Frequently Asked Questions - Silent 5622 Lasko

Can I use an extension cord with this heater?

No, always plug the heater directly into a 120V wall outlet. Using an extension cord, power strip, or surge protector can cause overheating and fire hazard.

How do I set the timer?

Press the Timer button repeatedly to increase the run time from 1 to 8 hours in 1-hour increments. After 8 hours, pressing once more sets it to continuous operation. The heater will turn off when the set time elapses.

Why does my heater shut off unexpectedly?

The tip-over switch or thermal overload protector may have activated. Ensure the heater is on a level surface and not blocked. If overheated, unplug for 10 minutes to cool down, then plug back in.

How do I change the temperature display from Fahrenheit to Celsius?

Press the (-) and (-) buttons (the same two) at the same time to toggle between °F and °C. The display will show the current room temperature in the selected unit.

What is the clearance required around the heater?

Keep combustible materials at least 3 feet (0.9 m) from the front and 1 foot (0.3 m) from the sides and rear of the heater.

Can I use this heater in a bathroom or outdoors?

No. This heater is for indoor residential use only and should not be used in wet or damp locations like bathrooms, laundry areas, or outdoors.

How do I clean the heater?

Unplug the heater. Use a vacuum with a brush attachment to remove lint and dirt from the intake grills every two weeks. For stubborn dirt, use a soft brush. Clean the body with a soft cloth. Never use alcohol or solvents.

What should I do if the heater displays a flashing temperature?

This indicates the thermal overload protector has activated due to overheating. Unplug the heater and wait at least 10 minutes for it to cool down. Then plug it back in and resume operation.

Does the heater have a low or high setting?

Yes, the heater has two heat settings: Heat(1) (1500W, high) and likely Heat(2) (750W, low) as indicated by the control buttons, though not explicitly stated in the manual.

Can I leave the heater unattended while operating?

The manual warns against leaving the heater operating unattended, especially near children or pets. It is recommended to turn off and unplug when not in use.

USER MANUAL Silent 5622 Lasko

This Heater is intended for use as supplemental heat.

This Heater is for residential use only.

It is not intended to be used in commercial, industrial or agricultural settings.

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE.

INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.

PROTECT YOURSELF AND OTHERS BY OBSERVING ALL

SAFETY INFORMATION. FAILURE TO COMPLY WITH

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR

PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

SAVE THESE INSTRUCTIONS

WARNING

IMPORTANT SAFETY INFORMATION

When using electrical appliances, these instructions and warnings should always be followed to reduce the risk of fire, electrical shock and injury to persons:

Read all instructions before using this Heater.

WARNING

- ALWAYS PLUG HEATERS DIRECTLY INTO A WALL OUTLET/RECEPTACLE. NEVER USE WITH AN EXTENSION CORD. DO NOT PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE OUTLET ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE MAZARD. PLUG UNIT DIRECTLY INTO A 120V WALL OUTLET ONLY.

• FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG FITS TIGHTLY INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVERHEATING. IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET. DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES.

- Make certain that the power source conforms to the electrical requirements of the Heater. - Extreme caution is necessary when any heater is used by or near children or invalids. The Heater should not be left operating unattended. Never leave children unattended when the heater is on or plugged in.

- The power cord is equipped with a three-prong grounded plug that must be inserted into a matching receptacle. Under no circumstances must the grounding prong be cut off the plug. Where a two-prong wall receptacle is encountered, it must be replaced with a properly grounded three-prong receptacle installed in accordance with the National Electrical Code (NEC) and all applicable local codes and ordinances. This work must be done only by a qualified electrician, using copper wire only. Do not attempt to defeat this safety feature.

- DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. DO NOT use Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres.

- Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner. To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.

- Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater. - Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.

- Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, lies a bad, where openings may become blocked. Do not depend on the on/off switch as the sole means of disconnecting power when servicing or moving the heater. Always unplug the power cord.

CAUTION

• Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners, or similar coverings as this may cause cord to overhaul. Arrange Power Cord away from room traffic and where it will not be tripped over. • This Heater is HOT when in use. To avoid burns, do not sit bare skin touch hot surfaces. Always use handle when moving this Heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep them at least 1 foot (0.3 m) from the sides and rear.

- This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER locate a Heater where it may fall into a bathtub or other water container. - DO NOT use Heater outdoors.

• This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for Agricultural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).

- This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Those limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and/or uses the equipment or equipment, which is not suitable for any use of any other equipment or equipment, and is not suitable for any use of any other equipment or equipment. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and on, the user is encouraged to try to correct the requirements. The equipment is used to ensure that it is necessary to perform an electronic device (including a device with a device labeled as a device) and is not suitable for any use of any other equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the equipment includes a device with a device being connected and modifications made to the equipment without the approval of manufacturer could void the user's authority to operate this equipment.

Please contact Customer Service at 800-233-0268 Monday through Friday from 8am to 5pm EST for assistance.

SAVE THESE INSTRUCTIONS

Rev. C 3/13

2

5622ES

MODELO 5622

FUNCIONAMIENTO

1. Carefully remove the Heater from the bag and the carton.

2. Place the Heater on a firm, level surface.

Plastic or rubber tabs, like the feet on this unit, may stick to furniture surfaces and/or hardwood floors. The unit may leave a residue that could darken, stain or leave permanent blemishes on the finish of certain furniture surfaces, including wood surfaces, and/or hardwood floors.

1. Plug the cord set into a 120 volt outlet. The Heater can not be plugged into a 220 volt outlet.

△WARNING

Be sure that the plug fits tightly into outlet. When plugs fit loosely into receptacles, they may slip partially or completely out of the receptacle with only the slight movement of the attached cord. Receptacles in this condition may overheat and pose a serious fire hazard; if covered by a curtain or drape, the fire hazard is even greater.

1. Turn the Heater ON by pressing the (9)

2. When initially turned on, the Heater will display the current room temperature in ° Fahrenheit. Press the (-) and (−) buttons at the same time to change the display to ° Celsius. Press the same two buttons together again to change the display back to ° Fahrenheit.

3. Upon turning the Heater on, the unit will display Heat(1) (1500 Watts) and will display the current room temperature. To turn the Heater OFF, press the (2) and unplug the Heater from the electrical outlet.

TIMER FUNCTION

The timer function may be activated when the Heater display is in any function. (Figure 2) This function allows you to set the length of time the Heater will run before turning itself off, from 1 hour to 8 hours. Pressing the Timer Button (☐) will increase the length of time by 1 hour each time this button is pressed. After the display reflects 8 hours, pressing the Timer Button (☐) once more will reset the Heater to run continuously. The Heater will turn off when the set time has elapsed. The unit can be turned back on by pressing the Power Button (☐).

Rev. C 3/19

AUTOMATIC TEMPERATURE CONTROL (Figure 3)

1. When the (or () button is pressed, the displayed temperature will begin to flash and the ( symbol will appear.
2. When you reach the temperature at which you want to set the unit, the set temperature will flash several times and then the display will return to indicate the current room temperature and will gradually change as the room temperature changes. NOTE: the temperature display does not indicate the temperature of the heated air being emitted by the heater.
3. When the air temperature reaches 2^ above the set temperature, the Heater will shut off.
4. When the air temperature reaches 1° below the set temperature, the Heater will turn on.
5. This function will cancel if the (Q) button is pressed. The Heater will now be in continuous Heat (I).

3

5622ES

MODEL 5622

SAFETY FEATURES

1. A Tip-Over Switch is built in to prevent operation if the Heater is tipped over.
2. A thermal overload protector is built in to prevent overheating.
3. If the Heater senses that the room temperature is too high, the Heater will shut off and the display will begin to flash. To reset the unit, unplug the Heater and wait 10 minutes for the Heater to cool down.
4. After the Heater has cooled down, follow the operation instructions described in this manual.

TROUBLE SHOOTING TIPS

If your heater shuts off unexpectedly or falls to operate, one of the previously mentioned safety features may have been activated to prevent overheating.
1. Be sure the power cord is plugged into a working electrical outlet. 2. Check your Temperature setting. The Heater may be off because it has reached the desired temperature setting.

RESET INSTRUCTIONS:

If the unit shuts down:

1. Unplug unit, wait 5-10 minutes.

2. Plug in and turn ON

3. Flag in and turn OK.

If you have a problem that can not be resolved by the steps listed above, contact Technical Assistance at 1-800-233-0268, Monday through Friday, between the hours of 8am and 6pm Eastern.

MAINTENANCE

WARNING

To reduce the risk of electrical shock and fire please observe the following instructions. Cleaning the Heater regularly will help to maintain its efficiency.

- Always unplug the cord before moving, servicing or cleaning.

- NEVER place the Heater in or near water. DO NOT IMMERSE HEATER IN WATER.

- Clean the Heater only with a vacuum equipped with a brush attachment: the vacuum will remove

the lint and dirt from the surface of the Heater.

- Vacuum intake grills every two weeks; this will help to maintain the optimum Heater performance.

- Use a toothbrush or other soft bristle brush to gently loosen any dirt not removed by the vacuum.

- NEVER attempt to take apart the Heater.

- Clean the body of the Heater with a soft cloth only.

- NEVER use ALCOHOL or SOLVENTS such as gasoline, benzene, paint thinner, or other harsh cleaners.

SERVICING: For servicing, other than general user maintenance, please contact Customer Service at 800-233-0268, Monday through Friday, from 8am-5pm Eastern.

STORAGE: Store the Heater with these instructions in the original carton in a cool, dry place.

LASKO PRODUCTS. INC. LIMITED WARRANTY (VALID IN THE USA, ITS TERRITORIES, AND CANADA ONLY)

WARRANTY COVERS: This product is warranted against defects in workmanship and/or materials.

HOW LONG THIS WARRANTY LASTS: This warranty extends only to the original purchaser of the product and lasts for three (3) years from the date of original purchase or until the original purchaser of the product sells or transfers the product, whichever first occurs.

WHAT LASKO WILL DO: Lasko will, all its sole option, repair or replace any part or parts that prove to be defective or replace the whole product with the same or comparable model. For all warranty claims, the product must be returned to Lasko Products, Inc. at customer expense with proof of purchase within the warranty period. Contact the Lasko customer service department to obtain a Return Authorization ("RA"). DO NOT return products without an RA or the warranty claim will not be processed.

WHAT THIS WARRANTY DOES NOT COVER: This warranty does not apply if the product was damaged or failed because of accident, improper handling or operation, shipping damage, abuse, misuse, unauthorized repairs made or attempted, or the use of the product for commercial or nonresidential service. This warranty does not cover shipping costs for the return of products to Lasko for repair or replacement. Lasko will pay return shipping charges from Lasko following warranty repairs or replacement.

ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY), LAST THREE YEARS FROM THE DATE OF ORIGINAL PURCHASE OR UNTIL THE ORIGINAL PURCHASER OF THE PRODUCT SELLS OR TRANSFERS THE PRODUCT, WHICHEVER FIRST OCCURDS AND IN NO EVENT SHALL LASKO'S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY INCLUDE (I) INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM ANY CAUSE WHATSOEVER, OR (II) REPLACEMENT OR REPAIR ANY HOUSE WITHOUT ANY INFORMATION. INCLUDING ANY OTHERS, INCLUDING ANY ANY OTHERS, INCLUDING ANY ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS, INCLUDING ANY OTHERS,

Some states and provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so these exclusions or limitations may not apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from state to state and province to province.

Proof of purchase is required before a warranty claim will be accepted.

CUSTOMER SERVICE:

Toll-Free [phone]. Email: [e-mail]

Our Customer Service team is available to assist you with product and service questions, and replacement parts. They can be reached Monday through Friday, 8am-5pm Eastern. Please have your model number available, as well as the type and style (located on the website of www.norpe draft).

Customer Service Dept. 820 Lincoln Ave. West Chester, PA 19380

(Please do not send product to this location) www.laskoproducts.com

PARTS FOR DISCONTINUED, OBSOLETE AND CERTAIN OTHER PRODUCTSMAY NOT BE AVAILABLE. DUE TO SAFETY REASONS, MANY ELECTRONIC COMPONENTS AND MOST HEATER COMPONENTS ARE NOT AVAILABLE TO CONSUMERS FOR INSTALLATION OR REPLACEMENT.

Manual printed in China

INSTRUCCIONES IMPORTANTES - MANUAL DE USO

Lasko®