PRO HC100 - Lawn mower Izzy - Free user manual and instructions

Product Type	Hair Clipper/Trimmer
Brand	Izzy
Model	PRO HC100
Power Supply	Rechargeable battery via charger (100-240V)
Charging Time	8 hours for full charge; 14-16 hours after full discharge
Operating Time	Approximately 45 minutes
Cutting Guides	Three adjustable guides: A (1-10mm), B (11-20mm), C (21-30mm)
Cutting Guide Regulator	Adjustable setting on the device
Trimmer Attachment	Detachable, for contouring and detail work
Indicators	Power/charge indication light
Charging Base	Storage/charge base included
Cleaning	Use included brush; lubricate trimmer with 2-3 drops of oil after use
Safety Features	Auto shut-off? Not specified; manual switch-off required; do not use in water
Accessories Included	Trimmer (1), cutting guides A, B, C, cleaning brush, lubricating oil, charger, storage/charge base
Intended Use	Domestic hair clipping for humans only
Battery Type	Rechargeable (Ni-MH or similar, not specified)
Warranty	2 years against manufacturing defects
Compliance	EU directives 2014/30/EU, 2014/35/EU, 2011/65/EU, 2009/125/EC
Manufacturer	BENRUBI Company (distributor)
Customer Service	Contact BENRUBI or authorized service centers

Frequently Asked Questions - PRO HC100 Izzy

How long does it take to fully charge the PRO HC100?

The first full charge or after long storage takes about 8 hours. After a full discharge, charge for 14-16 hours for optimal battery life.

How long does the battery last on a full charge?

The device operates for approximately 45 minutes on a full charge.

Can I use the device while it is charging?

No, the device must be switched off during charging. Do not leave it plugged in for more than 24 hours.

How do I attach the cutting guides?

Slide the cutting guide down into the slot on the side of the device until it clicks. To remove, slide it upward.

What are the available cutting lengths?

Three guides are included: Guide A (1-10 mm), Guide B (11-20 mm), and Guide C (21-30 mm). The cutting guide regulator allows fine adjustment within each range.

How do I clean and maintain the device?

After each use, brush hair residues from the trimmer and cutting guides. Apply 2-3 drops of lubricating oil to the trimmer. Clean the body with a damp cloth. Do not use abrasive cleaners or compressed air.

Is the device waterproof?

No, the device is not waterproof. Do not immerse it in water or other liquids. Keep it dry at all times.

Can I use the device on animals?

No, the device is intended for human use only. Using it on animals is not recommended and may void the warranty.

What should I do if the device falls into water?

Immediately unplug the charger without touching the water, and do not use the device. Contact an authorized BENRUBI service center.

How do I replace the battery?

The battery is not user-replaceable. At the end of life, remove the back cover with a screwdriver to access the battery and dispose of it properly. Do not attempt to repair the device yourself.

USER MANUAL PRO HC100 Izzy

Black and white ClipperPro hair curler with multiple teeth and a small bottle (no visible text or symbols)

Close-up of a black electronic device with a red indicator light and a label 'Euk. 1' (no other text or symbols visible)

Close-up of a black and silver hairdryer with a red mark on the handle, labeled 'Euk. 2' (no other text or symbols visible)

Σημειώσεις:

Thank you for having chosen an appliance from the IZZY range.

Safety interlocks

Please read these instructions carefully before using the appliance and save them for future reference. Please keep the sales receipt for guarantee purposes (pls see below “Guarantee and Customer Service”) Any use which does not conform to the instructions will absolve IZZY from any liability.

• Make sure your electricity supply is the same as the one shown on the underside of the device.
• Close supervision is necessary when your device is being used near children or infirm people. Ensure that they do not play with the device.
• This device is not intended for use by people with reduced physical, sensory or mental capabilities, children or those with lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the device by a person responsible for their safety.
• Switch off and unplug:
• If a disturbance occurs
• After use and if no recharge is needed
• If the device is out of use for a prolonged period of time
• Before removing or inserting accessories
• Before cleaning
• Never use the device for any other use than indicated.
• Do not use the device on animals. The device is intended for use only in humans.
• The device is intended only for domestic use. Any other use will cancel the warranty.

To avoid any risk of burns, fire, electric shock or injury, alwa follow the instructions below:

• Do not use the device when you bathe.
• Do not install in a place from which the device can easily fall or be pulled into a tub.
• Do not immerse the device and the charger in water or any other liquid
• Never leave the device unattended when the charger is plugged in,

except when charging.

• Always unplug the power cord before cleaning.
• Never expose the device to direct sunlight or temperatures above 60^ .
• Keep the body of the device always dry.
• Check the power cord periodically for possible damages. If the power cord or the plug of the device has been damaged, do not use the device and contact an authorized BENRUBI Service Center.

IMPORTANT: Do not cut the power cord of the charger at any case!

• Do not use / do not charge the device outdoors or in areas where it is carried out using various cleaning agents, insecticides, etc. in spray forr or in places where they carried oxygen administration.
• To avoid injury, do not use the device with cut or damaged blades, or damaged parts. Ensure that the blades are properly aligned before use.
• Always turn off the device by pressing the power switch before unplugging the power cord.
• No liability is accepted for any damage resulting from use for other purposes than those indicated in the instructions for use, faulty operation and repairs made from unauthorized technicians. Guarantee services are excluded in such cases.
• Use only attachments recommended by the manufacturer. Otherwise, may cause danger to the user and damage to the device.
• Do not move the device by pulling from the power cord. Make sure the power cord is not jammed in any way. Do not wrap the cord around the body of the device and do not tilt.
• Do not use an extension cord or voltage converter with this device.
• Never disconnect the device from the mains by pulling the cord. Disconnect always by pulling the plug.
• If the device falls into water or any other liquid:
• Take off the power cord.
• Do not put your hands into the liquid.
• Contact with one of the authorized BENRUBI repair centers and do no use the device.
• Do not use corrosive, abrasive detergents or hard brushes as they can scratch and cause damage to the device.
• In case of a possible damage, do not attempt to repair the device by yourself. Please contact one of the authorized BENRUBI service centers. Any repair made by an unauthorized BENRUBI Service Center CANCELS THE GUARANTEE.

• Any misuse of the device cancels the warranty.

• Use only original spare parts.
  • The device conforms to EU directive 2014/30/EU on Electromagnetic Compatibility, the 2014/35/EU Low Voltage Directive, the 2011/65/E RoHS Directive, and the directive 2009/125/EC for eco-design.

SAVE THESE INSTRUCTIONS

Parts of the Appliance

1. Trimmer
2. Cutting guide A (1-10mm)
3. On/Off button
4. Cutting guide display
5. Cutting guide regulator
6. Body
7. Power/charge indication light
8. Storage/charge base
9. Cleaning brush
10. Lubricating oil
11. Cutting guide B (11-20mm)
12. Cutting guide C (21-30mm)
13. Charger

Charging the Device

Caution: Do not charge the appliance outdoors where it comes into direct contact with the sun or in a very warm room.

- It takes about 8 hours to fully charge the battery for the first time or if it has not been used for a long time.

Make sure the device is switched off during charging!

You can charge the device in two different ways:

A. On the storage & charging basis

1. Insert the charger connector into the socket at the back of the base (8).
2. Place the device on the base pin (Fig.1).
3. Plug in. The charge indication light (7) will turn on.

3D rendered image of a black electronic device with a red indicator light and a labeled section 'Fig. 1' (no text or symbols on the device itself)

B. Directly into the socket

1. Insert the charger into the socket at the bottom of the appliance (Fig.2).
2. Plug in. The charge indication light (7) will turn on.

Close-up of a handheld electric shaver with a red indicator light and a black handle, labeled 'Fig. 2' (no other text or symbols visible)

Notes:

• The full-time operation takes about 45 minutes.
• Do not leave the appliance plugged in for more than 24 hours.
• Fully discharge the battery twice a year by leaving the device running until it stops. T recharge the battery fully for about 14-16 hours.
• Do not overload the appliance. If the device is not going to be used for a long time (2-3 months) unplug it and store it. Fully recharge the device when you want to use it again.

Attaching & Detaching Accessories

Attaching/detaching trimmer (1)

• To insert the trimmer (1), first insert the lower part of the head into the body of the device and then fasten the front part until a “click” is heard.
• To remove the trimmer (1), push the front of the head up and remove it from the body of the device.

Attaching/detaching cutting guides (2, 11 12)

• To insert one of the cutting guides, slide the guide down into the slot on the side of the device and snap until it clicks.
• To remove one of the cutting guides, slide the guide upwards and remove it.

Using the Cutting Guides

Cutting Guide	Length (mm)
A	1 - 10
B	11 - 20

Using the Appliance

• Clean the heads and the device after each use, so that it remains clean by bacteria that are created during use.
• Do not give the device to other people in order to avoid transmission of skin infections.

Hair Clipping

Preparing for hair clipping:

• Ensure that the device is fully charged before you start the clipping process.
• Use the device only on clean, dry hair. Do not use it on freshly washed hair.
• Make sure that the head of the person whose hair you intend to cut is at the same level as you chest. This ensures that all parts of the head are visible and easily accessible.

Clipping with e trimmer (without cutting guide)

CAUTION: Particular attention is needed when cutting without a cutting guide because the full width trimmer attachment removes any hair it touches.

1. Before you start to contour the hairline around the ears, comb the hair ends over the ears.
2. Attach the trimmer (1) to the body of the device.
3. Turn on the device by pressing the On/Off button (3). The power indication light (6) will turn on.
4. Turn the device in such a way that only one end of the cutting head touches the hair ends when shaping the contours around the ears. Cut only hair ends. The hairline should be close to the ear.
5. To shape the neckline and the sidebums, turn the device and make downward strokes. Move the device slowly and smoothly following the natural hairline.
6. When you finish clipping, turn off the device by pressing the On/Off switch (3). The power indicator light (7) will turn off.
7. Remove the trimmer.
8. Clean the trimmer and the device before storing it (see "Cleaning and care").

Clipping with full size trimmer and cutting guide

1. Comb the hair in the direction of growth.
2. Attach the trimmer (1) to the body of the device.
3. Attach the cutting guide (2, 11, 12) of your choice on the trimmer (see section "Use of cutting guides").
4. Adjust the cutting guide regulator (5) to the setting of your choice.
5. Turn on the device by pressing the On/Off button (3). The power indication light (7) will turn on.
6. Move the device slowly through the hair.
7. Remove the cut hair regularly from the cutting guide. If several hairs accumulate, remove the cutting guide from the device and blow and/or shake to clean it from the hairs.
8. When you finish clipping, turn off the device by pressing the On/Off button (3). The power indication light (7) will turn off.
9. Remove the cutting guide and the trimmer.
10. Clean the cutting guide, the trimmer and the device before storing it (see "Cleaning and care").

Tips for better results:

• For very short cuts (stubble look), use the cutting guide 3mm.
• For best results, move the device against the direction of hair growth. Since all hair does not grow in the same direction, you need to move the device in different directions (upward, downward or across).
• Ensure that the flat part of the cutting guide is in full contact with the scalp to achieve consistent result.
• Make overlapping passes over the head to ensure that you cut all hair that needs to be cut.
• To achieve a good result on curly, sparse or long hair, use a comb to guide the hair towards the device.

Cleaning & Care

Make sure the appliance is switched off before cleaning.

After each use:

• Brush the residues from hair.
• Cleaning should be done only with a soft brush, such as the one is provided in the packaging of the device.
• Put 2-3 drops of the lubricating oil to the trimmer.
• Do not use abrasive or corrosive cleaners for cleaning the body of the device and accessories.
• Never use compressed air to clean the cutting heads and cutting guides.

Trimmer

- Clean the head and the cutting guide with the brush.

Cutting guides

- Clean the accessories and the cutting guides with the brush.

Device body, charger, storage base

- Clean with a damp cloth. Dry thoroughly.

Technical Characteristics

Charging time: 8 hours

Autonomy time: 45 minutes

Battery Disposal

• Remove the back cover of the device with a screwdriver to locate the battery.
• Remove the battery from the product and recycle properly.

Safe Appliance Disposal

At the end of its working life, the product must not be disposed of as urban waste. It must be taken to a special local authority differentiated waste collection centre or to a dealer providing this service. Disposing of a household device separately avoids possible negative consequences for the environment and health deriving from inappropriate disposal and enables the constituent materials to be recovered to obtain significant savings in energy and resources.

As a reminder of the need to dispose of household devices separately, the product is marked with a crossed-out wheeled dustbin.

Guarantee & Customer Service

• BENRUBI Company guarantees its products for any manufacturing defect or defective materials for a period of two (2) years from the date of purchase or delivery by present purchase receipt. If your product malfunctions or you find any defects, please revert to the retail location you have purchased it from or contact an authorized BENRUBI Service Centre. To find the nearest authorized BENRUBI Service Centre, visit our website www.benrubi.gr. It is in the discretion of BENRUBI Company to replace or repair the defective product.
• The warranty does not cover damages resulting from normal wear, breakage, improper installation or maintenance of the product, mishandling, abnormal working conditions, failure to implement the instructions, conversion or repair of the product by an unauthorized technician who does not belong to the BENRUBI Service Centers.

Also, the warranty does not cover the following indicative factors:

• Stains, discoloration or scratches.
- Burns due to exposure to heat or flame.
- Damage from thermal shock (sudden temperature change or change of voltage).

FOR MORE INFORMATION PLEASE CONTACT:

(NEW) H. BENRUBI & FILS SA

27 Aghiou Thoma str, GR15124, Maroussi – Athens,

Tel.: [phone]

e-mail: [e-mail]