PowerWalker VFI 1000RT LCD - Inverter BlueWalker - Free user manual and instructions
Find the device manual for free PowerWalker VFI 1000RT LCD BlueWalker in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | UPS (Uninterruptible Power Supply) |
| Model | PowerWalker VFI 1000RT LCD |
| Brand | BlueWalker |
| Power Rating | 1000 VA / 900 W |
| Input Voltage | 160 - 290 VAC (adjustable) |
| Output Voltage | 208/220/230/240 VAC |
| Waveform | Pure Sine Wave |
| Backup Time | ~5-10 minutes at full load (depending on battery condition) |
| Battery Type | Sealed Lead-Acid (SLA), maintenance-free |
| Battery Quantity | 2 x 12V / 9Ah |
| Charging Time | 4-6 hours to 90% |
| Form Factor | Rackmount / Tower convertible (2U) |
| Dimensions (W x D x H) | 438 x 475 x 88 mm (19 x 18.7 x 3.5 inches) |
| Weight | 12.5 kg (27.6 lbs) |
| Interfaces | USB, RS-232, EPO, Smart Slot for SNMP card |
| Display | LCD with status indicators |
| Protection | Surge, overload, short circuit, low battery, overheating |
| Operating Temperature | 0°C to 40°C (32°F to 104°F) |
| Noise Level | < 45 dB at 1 m |
| Spare Parts Availability | Replacement batteries available (optional) |
| Repair Policy | Repair by qualified technician; do not open case |
| Maintenance | Keep vents clean; perform battery test periodically |
Frequently Asked Questions - PowerWalker VFI 1000RT LCD BlueWalker
How do I replace the battery in the PowerWalker VFI 1000RT LCD?
Turn off the UPS and disconnect input power. Remove the front bezel, slide out the battery compartment panel, disconnect the wires, and replace with same type (2x12V/9Ah). Reconnect, close panel, and recharge for 6 hours.
What is the typical runtime at half load?
At 450W load, you can expect approximately 12-15 minutes of backup time, depending on battery age and ambient temperature.
Can I connect the UPS to a generator?
Yes, but ensure the generator output is stable and within input specs (160-290V). The UPS may switch to battery if frequency or voltage fluctuates.
How do I silence the alarm?
Press the MUTE button on the front panel to silence the alarm temporarily. If alarm persists, check for faults like overload or battery failure.
What does the LCD panel display?
It shows input/output voltage, load level, battery capacity, status messages (normal, bypass, battery mode). Use the SELECT button to cycle through screens.
Can this UPS be mounted in a rack?
Yes, the PowerWalker VFI 1000RT LCD comes with rackmount brackets for standard 19-inch racks (2U space). Alternatively, you can place it as a tower.
Is the USB cable provided for monitoring?
Yes, a USB cable is included. Install the free software (PowerWalker Monitor) to view status, schedule shutdown, and manage events.
What does the EPO port do?
The Emergency Power Off (EPO) port allows you to connect an external switch to immediately cut output power in case of emergency. Connect normally open or normally closed contacts.
How often should I replace the battery?
Batteries typically last 3-5 years under normal conditions. Replace sooner if backup time drops significantly or the UPS indicates battery failure.
Can I connect multiple devices to the UPS?
Yes, but total load must not exceed 900W. The UPS has 8x IEC C13 outlets (some with battery backup and surge protection, some only surge). Check labels on outlets.
User questions about PowerWalker VFI 1000RT LCD BlueWalker
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Inverter in PDF format for free! Find your manual PowerWalker VFI 1000RT LCD - BlueWalker and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. PowerWalker VFI 1000RT LCD by BlueWalker.