Gate - Guitar effect pedal Hotone - Free user manual and instructions

Product Type	Noise Gate / Effects Gate
Brand	Hotone
Model	Gate
Dimensions	Approx. 74mm x 44mm x 47mm (2.9" x 1.7" x 1.9")
Weight	Approx. 150g (5.3 oz)
Power Supply	9V DC (center negative) 2.1mm jack, 60mA typical
Battery Option	9V battery (not included)
Controls	Threshold knob, Decay knob, On/Off footswitch
Input Impedance	1M Ohm
Output Impedance	100 Ohm
Current Draw	60mA max
Connectors	1 x 1/4" instrument input, 1 x 1/4" output
Housing	Aluminum alloy, miniature size
Mounting	Pedalboard friendly, non-slip rubber base
LED Indicator	Red LED for power/gate status
Operating Temperature	0°C to 40°C (32°F to 104°F)
Included Accessories	User manual, stickers
Cleaning	Wipe with dry cloth; avoid liquids and solvents
Warranty	1 year limited warranty

Frequently Asked Questions - Gate Hotone

What does the Hotone Gate pedal do?

The Hotone Gate is a noise gate that eliminates unwanted hum, hiss, and feedback from your signal chain. It opens and closes based on the threshold setting, allowing only signals above the threshold to pass.

How do I power the Hotone Gate?

Use a standard 9V DC power supply with center negative polarity (2.1mm jack). It draws about 60mA. Alternatively, you can use a 9V battery (not included).

How do I set the threshold and decay controls?”

Start with the Threshold knob fully clockwise (most sensitive) and Decay at minimum. Play your instrument and gradually turn Threshold counterclockwise until the gate closes when you stop playing. Then adjust Decay to control how fast the gate closes after the signal stops.

Can I use the Hotone Gate in the effects loop?”

Yes, it can be used in the effects loop of your amplifier or in the signal chain before or after other pedals. Typically, it is placed after distortion pedals to gate noise from high gain.

What is the input/output impedance?”

Input impedance is 1M Ohm and output impedance is 100 Ohm, making it suitable for most guitar pedals and amplifiers without signal loss.

Does the Hotone Gate have a true bypass?”

Yes, it features true bypass switching, so your signal is uninterrupted when the pedal is off.

How compact is the Hotone Gate?”

It is extremely compact, measuring approximately 74mm x 44mm x 47mm, which is about the size of a standard mini pedal. It fits easily on crowded pedalboards.

Can I use the Hotone Gate with bass guitars?”

Yes, it works with bass as well. The frequency range is wide enough for low frequencies. Adjust the threshold accordingly.

What should I do if the gate does not close completely?”

Check the Threshold setting; it may be too low (too much clockwise). Also ensure the power supply is stable and the input cable is properly connected. Try adjusting the Decay control to a faster setting.

Is the Hotone Gate durable for touring?”

Yes, its aluminum alloy housing is robust and lightweight. However, avoid exposing it to extreme temperatures or moisture.

USER MANUAL Gate Hotone

THANK YOU FOR PURCHASING A HOTONE PRODUCT!

GATE is a noise reduction stompbox for guitarists/bassists. No matter what kind of style you are playing, this tiny pedal will effectively keep noise and hum away from your pedalboard without changing your own tone.

Use the CUT button to enable a harder noise reduction mode.

Controls the noise gate threshold

Plug in 9V DC adapter (center negative)

Controls the low cut frequency from 40Hz to 120Hz (available ONLY in CUT mode)

Structural Design Protected by Patent Exterior Design Protected by Patent

Controls the high cut frequency from 5kHz to 15kHz (available ONLY in CUT mode)

Push it to enable a harder noise reduction mode

Specifications Current Consumption: 34mA Dimensions: 74 mm (D) × 44mm (W) × 44 mm (H) Weight: 190 g

www.hotoneaudio.com