M-DL-WAVES3 - Hand blender ALLEN & HEATH - Free user manual and instructions

Product Type	Audio Networking Card for Allen & Heath dLive systems
Brand	Allen & Heath
Model	M-DL-WAVES3
Compatibility	dLive MixRack or Surface I/O Port
Audio Channels	128x128 at 48kHz or 96kHz
Network Protocol	Waves SoundGrid
Network Ports	3 x locking EtherCon (Gigabit switch)
LED Indicators	Link Status (flashes for network activity)
Firmware Requirement	dLive firmware V1.3 or higher
Software & Drivers	Download from Waves website: waves.com/downloads/allen-heath
Documentation	dLive Firmware Reference Guide at allen-heath.com
Warranty	Limited 1 year manufacturer warranty
Compliance	EMC 2014/30/EU, Low Voltage 2014/35/EU
Installation	Switch off system, remove blank panel, insert card, tighten thumb screws
Clock Synchronization	Set via dLive Audio Sync screen: Internal for master, I/O Port for slaves
Signal Patching	Use dLive I/O screen to route signals to/from I/O Ports
Manufacturer Contact	Allen & Heath Limited, Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK
Website	www.allen-heath.com

Frequently Asked Questions - M-DL-WAVES3 ALLEN & HEATH

How do I install the M-DL-WAVES3 card?

First, switch off the system. Remove the 4 screws securing the I/O Port blank panel on the dLive MixRack or Surface. Slide the card into the slot and press firmly into the mating connector. Secure by tightening the 4 captivated thumb screws.

What firmware is required for the M-DL-WAVES3?

The M-DL-WAVES3 requires dLive firmware version V1.3 or higher. You can download the latest firmware from the Allen & Heath website.

Where can I find drivers and software for the Waves SoundGrid platform?

Visit the Waves website at waves.com/downloads/allen-heath to download drivers, software, and further documentation for the Allen & Heath platform.

How many audio channels does the M-DL-WAVES3 support?

The card supports up to 128x128 channels at either 48kHz or 96kHz sample rates.

How do I set the clock source when using the M-DL-WAVES3?

Use the dLive MixRack / Audio / Audio Sync screen. Set the clock source to Internal on the master system, or to the relevant I/O Port on all other networked (clock slave) systems.

What network ports are available on the card?

The M-DL-WAVES3 features a built-in Gigabit switch with 3 locking EtherCon ports, allowing direct connection of up to three devices.

How can I route audio signals to and from the card?

Use the dLive I/O screen to patch signals from or to the I/O Ports where the card is installed.

What does the Link Status LED indicate?

The Link Status LED flashes to indicate network activity on the SoundGrid ports.

What is the warranty period for the M-DL-WAVES3?

The product carries a limited one-year manufacturer's warranty. Full conditions are available at www.allen-heath.com/legal.

What safety and compliance standards does the M-DL-WAVES3 meet?

The card complies with the European Electromagnetic Compatibility directive 2014/30/EU and the Low Voltage directive 2014/35/EU.

USER MANUAL M-DL-WAVES3 ALLEN & HEATH

M-DL-WAVES3 fitting note

M-DL-WAVES3 is one of several audio networking options that can be fitted to an Allen & Heath dLive I/O Port. It provides a 128x128ch 48/96kHz interface to the Waves SoundGrid networking and processing platform.

Fitting the card

1. Switch the system off.
2. Remove the 4 screws securing the I/O Port blank panel on the dLive MixRack or Surface.
3. Slide the card into the slot and press it firmly into the mating connector.
4. Secure the card by tightening the 4 captivated thumb screws.

2

Pure diagram of two vertical arrows pointing left and right, no text or symbols present

3

Software and firmware

Go to the Waves website to learn more about Waves for the Allen & Heath platform:

http://www.waves.com/live-sound/allen-heath

Download further documentation, follow the instructions, set up the hardware and install the card driver and software:

http://www.waves.com/downloads/allen-heath

Download and install the latest version of dLive firmware:

http://www.allen-heath.com

i M-DL-WAVES3 requires dLive firmware V1.3 or higher.

Front panel

SoundGrid ports

A built-in Gigabit switch with 3 locking EtherCon ports for connecting up to three devices directly

Link Status

Flashes to indicate network activity

Setting clock and patching signals

Use the dLive I/O screen to patch signals from or to the I/O Ports.

Use the MixRack / Audio / Audio Sync screen to select the clock source. Set this to Internal on the master system, or to the relevant I/O Port on all other networked (clock slave) systems.

For more information on dLive setup and functions please refer to the dLive Firmware Reference Guide available for download at www.allen-heath.com.

A limited one year manufacturer's warranty applies to this product, the conditions of which can be found at: www.allen-heath.com/legal.

This product complies with the European Electromagnetic Compatibility directive 2014/30/EU and the European Low Voltage directive 2014/35/EU.

Copyright © 2016 Allen & Heath. All rights reserved.

ALLEN&HEATH

Allen & Heath Limited, Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK

http://www.allen-heath.com