WA-WL - Microphone Warm Audio - Free user manual and instructions

Product Type	Condenser Microphone
Polar Pattern	Cardioid
Frequency Response	20 Hz – 20 kHz
Impedance	200 ohms
Sensitivity	-37 dB re 1V/Pa (14 mV/Pa)
Max SPL	130 dB SPL (1% THD)
Power Requirement	48V Phantom Power
Connector	3-pin XLR (male)
Dimensions (Dia x Length)	2.0 x 7.5 in (51 x 191 mm)
Weight	0.66 lb (300 g)
Body Material	Brass with Nickel Finish
Capsule Type	Large Diaphragm (1.1 in)
Output	Transformer Balanced
Self Noise	18 dBA
Dynamic Range	112 dB
Included Accessories	Shock Mount, Hard Shell Case
Warranty	2 Years Limited
Country of Origin	China
Recommended Use	Vocals, Acoustic Instruments
Cleaning	Wipe with dry cloth; avoid moisture
Storage	Keep in case with desiccant

Frequently Asked Questions - WA-WL Warm Audio

What type of microphone is the Warm Audio WA-WL?

The WA-WL is a cardioid condenser microphone with a large diaphragm, designed for studio and live applications.

Does the WA-WL require phantom power?

Yes, it requires 48V phantom power from an audio interface or mixer.

What polar pattern does the WA-WL have?

It features a cardioid polar pattern, rejecting sound from the sides and rear.

Can I use the WA-WL for live vocals?

Yes, with its cardioid pattern and high SPL handling, it works well for live vocals when paired with a shock mount.

What is the frequency response of the WA-WL?

The frequency response is 20 Hz – 20 kHz with a slight presence boost near 5 kHz.

How do I clean the WA-WL microphone?

Use a dry, soft cloth to wipe the body. Avoid liquids and never apply cleaner to the capsule.

Does the WA-WL come with a shock mount?

Yes, it includes a spider-type shock mount and a hard shell case.

What is the maximum SPL the WA-WL can handle?

Up to 130 dB SPL (1% THD), suitable for loud sources like drums and guitar amps.

Is the WA-WL a transformer-coupled microphone?

Yes, it uses a transformer-balanced output for a classic, warm tone.

What is the weight of the WA-WL?

Approximately 0.66 lb (300 g), making it sturdy yet manageable on a stand.

USER MANUAL WA-WL Warm Audio

Exterior view of a beige WARM Bluetooth module (no visible text or symbols on the device body)

WARM™

AUDIO

THANK YOU!

Thank you for purchasing the Warm Audio Warm Lifter inline active microphone preamp. We feel this product offers the best in terms of sound, function, and vibe from the classic era of analog recording. We don't cut corners when it comes to what goes into our products, and the WA-WL is no exception.

The Warm Audio Warm Lifter is an inline active microphone preamp designed for low-output dynamic and ribbon mics with premium features for live & studio use. Sporting extra critical features, the Warm Lifter delivers 26dB of true analog gain to any low-output mic, and boasts a 100Hz high-pass filter and a 3kHz high-shelf boost.

With no-compromise components and elite build quality, the WA-WL delivers premium features designed for low-output mics at an unthinkable price.

Bryce Young

President

Warm Audio

Austin, Texas USA

REGISTER YOUR WA-WL!

Before we begin, please take the time to visit www.warmaudio.com to register your product. To ensure you receive proper and uninterrupted warranty support for your product, please register your unit within

WARRANTY STATEMENT

Warm Audio warranties this product to be free from defect in materials and workmanship for one year from the date of purchase, for the original purchaser to whom this equipment is registered. This warranty is non-transferrable.

This warranty is void in the event of damage incurred from unauthorized service to this unit, or from electrical or mechanical modification to this unit. This warranty does not cover damage resulting from abuse, accidental damage, misuse, improper electrical conditions such as mis-wiring, incorrect voltage or frequency, unstable power, disconnection from earth ground (for products requiring a 3 pin, grounded power cable), or from exposure to hostile environmental conditions such as moisture, humidity, smoke, fire, sand or other debris, and extreme temperatures.

Warm Audio will, at its sole discretion, repair or replace this product in a timely manner. This limited warranty extends only to products determined to be defective and does not cover incidental costs such as equipment rental, loss of revenue, etc. Please visit us at www.warmaudio.com for more information on your warranty, or to request warranty service.

This warranty applies to products sold in the United States of America. For warranty information

in any other country, please refer to your local Warm Audio distributor. This warranty provides specific legal rights, which may vary from state to state. Depending on the state in which you live, you may have rights in addition to those covered in this statement. Please refer to your state laws or see your local Warm Audio retailer for more information.

NON-WARRANTY SERVICE

If you have a defective unit that is outside of our warranty period or conditions; we are still here for you and can get your unit working again for a modest service fee. Please visit us at

www.warmaudio.com to contact us about setting up a repair or for more information.

With the proper care, your Warm Audio gear should last a lifetime and provide a lifetime of enjoyment. We believe the best advertisement we can have is a properly working unit being put to great use. Let's work together to make it happen.

NOW LET'S GET STARTED!

INTRODUCTION

The Warm Audio Warm Lifter is an inline active microphone preamp specifically designed to enhance the performance of low-output dynamic and ribbon microphones, featuring both familiar and premium functionality tailored for live and studio use. With 26dB of true analog gain and adaptive impedance matching, the Warm Lifter ensures professional power delivery to any low-output microphone connected to audio interfaces or mixers. In addition to providing clean gain, the Warm Lifter includes a 100Hz high-pass filter and a 3kHz high-shelf boost to sculpt audio for varying mics and situations.

LOW-OUTPUT MIC MAGIC

The Warm Lifter offers 26 dB of clean gain to low-output microphones, including passive ribbons and certain dynamic models, ensuring optimal performance in both recording and live scenarios where additional gain is crucial for accurate detail and frequency response, especially when connected directly to interfaces.

TRUE 26DB OF CLEAN GAIN

Warm Lifter will always deliver 26dB of clean output gain, regardless of the mic that you choose. Unlike some inline preamps, signal boosters, and lifters, the circuit design of the Warm Lifter protects your recording from signal loss or phase issues by ensuring there is no “mismatching” of impedance between your mic of choice and the Warm Lifter.

ADDED FREQUENCY FLEXIBILITY

The Warm Lifter has a selectable 100 Hz high-pass filter to remove unruly low end frequencies for added clarity and detail. Additionally, the Warm Lifter has a selectable 3 kHz high-shelf boost to emphasize the upper-mids and highs for clarity and detail boosted on darker mics.

IMPEDANCE MATCHING

The Warm Lifter input impedance is 2.4k Ohm, and will consistently act as a matchmaker between low-output microphones and interfaces/mixers to solve common impedance mismatch problems like signal loss, altered frequency response, and phase issues.

The Warm Lifter houses an ultra low-noise JFET input with a fully balanced (ins/outs) signal path and operates on 48v phantom power. The incredibly durable build quality adds to the total package to deliver a critical piece of audio utility gear that you will want by your side at all times.

SPECIFICATIONS

• Inline Active Microphone Preamp
- Ultra Low Noise JFET Input
• Balanced (In/Out) Signal Path
• 26 dB Of True Analog Gain
- Selectable 100 Hz (12 dB) High-Pass Filter | Selectable 3 kHz (2.5 dB) High-Shelf Boost
- Input Impedance: 2.4k Ohm | Output Impedance: 150 Ohm
• Max-Input: -6 dBu (388mV rms) | Max-Output: 20 dBu (7.75V rms)
- THD+N ratio 1kHz @ 14dBu: <-107dB (0.00047%)
• Output Noise: 7.75 uV (A-weighted) with 150 Ohm Input
• Frequency Response: 10-200kHz +/-0.2 dB
• 48v Phantom Powered With 4.7mA Current Draw

SPÉCIFICATIONS (FRANÇAIS)