VT0403 - Faucet Oliveri - Free user manual and instructions

Product Type	Single lever mixer faucet
Brand	Oliveri
Model	VT0403
Installation	Requires licensed plumber in accordance with local regulations
Standards	AS/NZS 3718
Maximum Operating Pressure	6 bar (600 kPa)
Recommended Operating Pressure	1 - 5 bar (100 - 500 kPa)
Maximum Hot Water Temperature	70°C
Recommended Hot Water Temperature	60°C
Flow Rate	6.5 L/min at 300 kPa
Finish	Polished chrome-plated
Country of Origin	Italy
Pre-assembled	Yes, do not disassemble (may void warranty)
Isolation Valves Required	Yes, with filters (not supplied)
Care Instructions	Clean with soft cloth and warm soapy water; rinse and dry. Avoid abrasive or acid-based cleaners.
Aerator Maintenance	Unscrew and clean periodically, especially if pressure drops
Warranty	Refer to warranty card enclosed in carton

Frequently Asked Questions - VT0403 Oliveri

What is the maximum operating pressure for the Oliveri VT0403 faucet?

The maximum operating pressure is 6 bar (600 kPa). If pressure exceeds this, a pressure reducing device must be installed.

Can I install the faucet myself?

No, installation must be performed by a licensed plumber in accordance with local regulations.

What is the recommended water temperature?

The recommended hot water temperature is 60°C, with a maximum of 70°C.

What is the flow rate of the VT0403?

The flow rate is 6.5 litres per minute at a pressure of 300 kPa.

How should I clean the faucet?

Use a soft cloth and warm soapy water. Rinse and dry thoroughly. Avoid abrasive or acid-based cleaning products.

Why is my water pressure dropping?

The spout aerator may be clogged. Unscrew and clean the aerator periodically to restore pressure.

Do I need isolation valves?

Yes, stop valves (preferably with filters) must be used to allow isolation. These are not supplied with the mixer.

What standards does the VT0403 comply with?

It complies with AS/NZS 3718.

Where is the faucet manufactured?

The VT0403 is made in Italy.

Is the faucet pre-assembled?

Yes, it is pre-assembled and tested. Do not disassemble, as this may void the warranty.

USER MANUAL VT0403 Oliveri

THIS MIXER TAP MUST BE INSTALLED BY A LICENSED PLUMBER IN ACCORDANCE WITH LOCAL REGULATIONS

This Oliveri tap is manufactured to standard AS/NZS 3718.

MAX OPERATING PRESSURE:	6 bar (600kPa)
RECOMMENDED OPERATION PRESSURE:	1-5 bar (100-500kPa)
MAX HOT WATER TEMPERATURE:	70°C
RECOMMENDED HOT WATER TEMPERATURE:	60°C
FLOW RATE:	6.5 L/min 3 bar (300kPa)

In case of operating pressures higher than 6 bar (600kPa) a pressure reducing device must be installed on the feed lines. Failure to do so where required will void warranty.

Before attempting any work involving mains water supply lines, ensure the water supply is shut off.

Stop valves (preferably with filters) must be used when installing your Oliveri mixer to allow isolation. (not supplied with mixer). Failure to do so where required will void warranty.

This mixer tap is already pre-assembled and tested. Do not disassemble, as this may void the warranty.

This mixer tap must be installed in accordance with these instructions.

VT0403

MADE IN ITALY

VTO4O3 Instructions

Olivéri

VILO VT0403

Modern kitchen sink with curved handle and faucet (no text or symbols visible)

VT0403 Single lever mixer.

CARE & MAINTENANCE

Unscrew and clean the spout aerator periodically - especially if you notice a drop in water pressure. The polished chrome-plated finish on your Oliveri mixer tap will resist stains and dirt build-up.

Clean with a soft cloth and warm soapy water as necessary – rinse and dry after cleaning. Avoid using abrasive or acid based cleaning products.

SERVICE & WARRANTY

Please refer to warranty card enclosed in carton.

VT0403