EasiCut 610XT - Hedge Trimmer FLYMO - Free user manual and instructions

Product Type	Hedge Trimmer
Brand	Flymo
Model	EasiCut 610XT
Blade Length	61 cm (610 mm)
Blade Material	High-carbon steel, laser-cut and diamond-ground
Cutting Action	Dual-action blades for reduced vibration
Power Source	Electric corded (230V ~ 50Hz)
Motor Power	500 W
Weight	3.5 kg
Overall Length	90 cm
Handle Design	Adjustable rear handle with soft grip, front ergonomic grip
Safety Features	Two-handed operation, blade guard, safety switch
Cutting Capacity	Up to 25 mm branch diameter
Noise Level (Lpa)	85 dB(A)
Vibration Level	2.8 m/s²
Maintenance	Light oiling of blades after each use; clean with damp cloth
Storage	Use blade cover; store indoors in dry place
Warranty	2 years (subject to terms)
Included Accessories	Blade cover, user manual

Frequently Asked Questions - EasiCut 610XT FLYMO

How do I start the Flymo EasiCut 610XT?

Ensure the power cord is plugged into an appropriate outlet. Hold the front handle with one hand and the rear handle with the other. Press and hold the safety lock button on the rear handle, then squeeze the trigger switch. Release the safety lock once the trigger is held.

Can I use the trimmer in wet conditions?

No, never use the hedge trimmer in rain or on wet hedges to avoid electric shock. Always operate in dry conditions and ensure hands are dry.

What is the correct way to cut branches?

Use a sweeping motion from the bottom up. For thick branches (up to 25 mm), cut gradually. Avoid forcing the blades.

How do I maintain the blades?

After each use, clean the blades with a damp cloth and apply light oil (e.g., machine oil) along the cutting edge. Regularly check for dullness and have them sharpened professionally if needed.

What should I do if the blades jam?

Release the trigger switch and disconnect from power. Remove any stuck debris using a stick or pliers (wear gloves). Do not touch the blades without protection.

Is the trimmer suitable for left-handed users?

The handles are symmetrically designed but are optimized for right-handed users. Left-handed users can still operate safely with both hands on the grips.

How do I store the hedge trimmer?

Always fit the blade cover before storage. Store in a dry, frost-free place, out of reach of children. Coil the power cord loosely.

What type of extension cord should I use?

Use a heavy-duty outdoor extension cord with a minimum cross-section of 1.5 mm². Ensure it is approved for outdoor use and rated for the power of the trimmer.

Why does the trimmer stop during use?

Possible causes: thermal protection activated (let cool for 10 minutes), power cord damaged, or overload. Check cord and reset if necessary. If persistent, consult a professional.

Can I sharpen the blades myself?

Sharpening is not recommended for inexperienced users. Use a professional sharpening service. Improper sharpening can damage the blades or reduce cutting efficiency.

USER MANUAL EasiCut 610XT FLYMO

Remark: "xx" stands for customer and country variants. The basic product number is before the hyphen.

EN Operator's manual

Electric Hedge Trimmer

Carton Contents

A

Line drawing of a person using a hair sh therm tool to cut a ruler (no text or symbols present)

B

C

Line drawing of a person using a sawtooth tool to cut a sawtooth (no text or symbols present)

D

Line drawing of hands using a manual power tool to cut a saw (no text or symbols)

EN

1. SAFETY 4
2. INITIAL OPERATION....5
3. OPERATION....6
4. MAINTENANCE 6
   5.STORAGE 6
5. TROUBLESHOOTING 6
6. DISPOSAL 6
7. TECHNICAL DATA 7
8. SERVICE/WARRANTY....7

Original instructions.

This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the product by a person responsible for their safety. Children should be supervised to ensure that they do not play with the product. The use of this product by young people under the age of 16 is not recommended.

Intended use:

The FLYMO Hedge Trimmer is intended to cut hedges, shrubs and grass coverings in private domestic gardens and allotments.

The product is not intended for long term use.

IGER! Risk of injury!

→ Do not use the product to cut lawns / lawn edges, to chop up material or to make compost.

Carton Contents:

① Mains cable
② Handguard
③ Blade cover
④ Operator's manual

IMPORTANT!

Please check if the contents of the carton are correct BEFORE assembling your new product.

IF ANY PARTS ARE MISSING CONTACT:

Husqvarna UK Ltd. Customer Service Department direct Telephone: [phone] UK 1800 882 350 ROI

Fax: [phone]

1. SAFETY

Important! Read the operator's manual carefully before use and keep for future reference.

If not used properly this product can be dangerous. The warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this product. The operator is responsible for following the warnings and instructions in this manual and on the product. Never use the product unless the guards provided by the manufacturer are in the correct position.

Symbols on the product:

Head operator's manual.

safety glasses and ear protection.

er - Keep hands away from blade.

Not let the product become wet with rain or other moisture. Do not leave the product outdoors while it is raining.

connect the mains cable if the cable becomes damaged or cut.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and / or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains operated (corded) power tool or battery operated (cordless) power tool.

1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adaptor plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tools may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and / or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5) Service

Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

Hedge trimmer safety warnings:

- Keep all parts of the body away from the cutter blade. Do not remove cut material or hold material to be cut when blades are moving. Make sure the switch is off when clearing jammed material.

A moment of inattention while operating the hedge trimmer may result in serious personal injury.

- Carry the hedge trimmer by the handle with the cutter blade stopped. When transporting or storing the hedge trimmer always fit the cutting device cover. Proper handling of the hedge trimmer will reduce possible per sonal injury from the cutter blades.

- Hold the power tool by insulated gripping surfaces only, because the cutter blade may contact hidden wiring or its own cord.

Cutter blades contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.

- Keep cable away from the cutting area. During operation the cable may be hidden in shrubs and can be accidentally cut by the blade.

Additional Safety Recommendations

DANGER! Small parts can be easily swallowed. There is also a risk that the poly-bag can suffocate toddlers. Keep toddlers away when you assemble the product.

Work area safety

Only use the product in the manner and for the functions described in these instructions.

The operator or user is responsible for accidents or hazards occurring to other people or their property.

While operation and transport pay special attention to the hazard for third parties.

Risk of stumbling. While operation pay attention to the cable.

Warning! When wearing hearing protection, and due to the noise produced by the product, the operator may not notice persons approaching.

Do not use the product when a thunderstorm is approaching.

Do not use the product nearby a water.

Electrical safety

The British Standards Institute recommend the use of a Residual Current Device (R.C.D.) with a tripping current of not more than 30 mA. Check your R.C.D. every time you use it.

Before use, examine cable for damage, replace it if there are signs of damage or ageing.

If the replacement of the supply cord is necessary, this has to be done by the manufacturer or his agent in order to avoid a safety hazard.

Do not use the product if the electric cables are damaged or worn.

Immediately disconnect from the mains electricity supply if the cable is cut, or the insulation is damaged. Do not touch the electric cable until the electrical supply has been disconnected.

Your electric cable must be untangled, tangled cables can overheat and reduce the efficiency of your product.

Always disconnect the mains cable before disconnecting any plug, cable connector or extension cable.

Switch off, remove plug from mains and examine electric supply cable for damage or ageing before winding cable for storage. Do not repair a damaged cable, send the product to the next FLYMO service Center or dealer authorised by FLYMO.

Always wind cable carefully, avoiding kinking.

Use only on AC mains supply voltage shown on the product rating label.

Under no circumstances should an earth be connected to any part of the product. If the product starts unintentionally when the mains plug is connected, disconnect the mains at once. Contact FLYMO Service to check the product.

DANGER! This product makes an electromagnetic field while it operates. This field may under some conditions interfere with active or passive medical implants. To decrease the risk of conditions that can possibly injure or kill, we recommend persons with medical implants to speak with their physician and the medical implant manufacturer before you operate the product.

Cables

Use only permitted extension cables as per HD 516.

→ Ask your electrical specialist.

Personal safety

Always wear suitable clothing, protective gloves, and stout shoes.

Avoid contact to the oil of the blade in particular when you react allergic with it.

Thoroughly inspect the area where the product is to be used and remove all wires and other foreign objects.

Always hold the product properly with both hands and both handles.

Before using the product and after any impact, check for signs of wear or damage and repair as necessary.

Never attempt to use an incomplete product or one with an unauthorised modification.

Power tool use and care

Know how to stop the product quickly in an emergency.

Never hold the product by the guard.

Do not use the product if the protection equipments (protection cover, quick blade-stop) are damaged.

Do not use ladders whilst operating the product.

Disconnect the mains cable:

– before leaving the product unattended for any period;

– before clearing a blockage;

– before checking, cleaning or working on the appliance;

- if you hit an object. Do not use your product until you are sure that the entire product is in a safe operating condition;

- if the product starts to vibrate abnormally. Check immediately. Excessive vibration can cause injury.

– before passing to another person.

Only use the product between 0 - 40 °C.

Maintenance and storage

RISK OF INJURY!

ot touch blades.

→ When finishing or interrupting work push up protection cover.

Keep all nuts, bolts and screws secure to be sure the product is in safe working condition.

If the product got hot during operation, let it cool down before storage.

If you want to use an extension cable when operating your product, only the following cable dimensions should be used.

1.0 mm ^4 : max. length

- 1.5 mm²: max. length

- 2.5 ~mm^2 : max. length 100 m

Minimum rating:

1.00 mm ^2 size cable, 10 amps 250 volts AC.

- YOUR HEDGETRIMMER IS SUPPLIED WITH CABLE WIRED DIRECTLY INTO THE PRODUCT.

1. If the supply cord is damaged, it must be replaced by your local Husqvarna UK Ltd. Approved Service Centre or similarly qualified persons in order to avoid a hazard.

2. Flymo Extension Cables are available from your local Husqvarna UK Ltd. Approved Service Centre.

3. Do not wire an extension cable directly to your product yourself. Please contact your local Husqvarna UK Ltd. Approved Service Centre for further information on the connectors and kits available.

4. Only use extension cables specifically designed for outdoor use and which conform to one of the following specifications: Ordinary rubber (60245 IEC 53), Ordinary PVC (60227 IEC 53) or Ordinary PCP (60245 IEC 57)

Connectors

IMPORTANT!

- Connectors are suitable for use with 2 core cable only. Under no circumstances should these connectors be used for earthed products.

- All connectors and cables are of splashproof construction. They are not waterproof and must not be left outside permanently nor should they be submerged or immersed in water. Do not let cable lay or trail through pools of water or splashed with water from hose pipes.

Mains Plug Replacement

IMPORTANT!

If the plug supplied is cut off it should be destroyed. There is an electric shock hazard if a cut off plug is inserted into a 13 amp socket.

1. No earth required. Our products are double insulated to EN60745 and under no circumstances should an earth be connected to any part of the product.

2. Ensure the mains voltage suits your product

3. IMPORTANT!

The wires in the mains lead are coloured in accordance with the followingcode:

BLUE - NEUTRAL

BROWN - LIVE

The wire which is coloured BLUE must be connected to the Terminal which is marked with the letter "N" or coloured BLACK.

The wire which is coloured BROWN must be connected to the Terminal which is marked with the letter "L" or coloured RED.

1. It is important that the outer sheath is clamped correctly into the 3-pin plug.

2. If in doubt consult your local Service Repairer or qualified electrician before the machine is used.

3. A 13 amp fuse must be fitted to the Mains Plug.

4. The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard against electrocution.

If your product is hard wired i. e. non-detachable mains electric cable, a conversion kit and extension cable is available from all Approved Service Centres which can be found in your local Yellow Pages.

3. OPERATION

To start your hedge trimmer:

1. Remove the blade cover (A).
2. There are three switch levers fitted to your Hedgetrimmer.
3. To start, push forward the lock-off button (B1), squeeze the main switch lever (B2), release lock-off button.
4. Main switch lever (B2) and one other need to be held in the operating position (B3 or C1) for the product to start.

To stop your hedge trimmer:

• Move hedge trimmer away from cutting area before stopping.
  → To stop, release any switch lever (D).

How to use your hedge trimmer:

1. Inspect area to be cut before each use –remove objects which can be thrown or become entangled in the cutting blades.
2. Always keep the hedge trimmer in front of yourbody. Hold handle firmly with both hands andstand in a secure and stable position.
3. Allow the cutting blades to reach full speed before entering the material to be cut.
4. Always work going away from people and solid objects such as walls, large stones, trees, vehicles etc.
5. If blade stalls, immediately stop the hedgetrimmer. Disconnect the hedge trimmer from the power source and clear jammed debris from the cutting blades. Inspect blades and repair or replace as needed.

Top cutting:

Use a wide sweeping motion (E). A slight downward tilt of the cutting blades in the direction of motion gives the best cutting results.

Side cutting:

When trimming the sides of the hedge, begin at the bottom and cut upwards (F), tapering the hedge inward at the top. This shape will expose more of the hedge, resulting in more uniformed growth.

4. MAINTENANCE

WARNING!

Disconnect from the mains electricity supply, before attempting any maintenance or adjustment.

Cleaning (G):

1. Using a soft brush – remove debris from all air intakes and cutting blade.
2. Wipe over surface of your hedge trimmer with a dry cloth.

IMPORTANT!

→ Never use water for cleaning your hedgetrimmer.
→ Do not clean with chemicals, including petrol, or solvents – some can destroy critical plastic parts.

Lubricating the cutting blade:

For easier operation and longer life, lubricate the cutter blades before and after use. Apply the oil so that it runs between the two blades (G).

Service Recommendations:

1. We strongly recommend that your product is serviced at least every twelve months, more often in a professional application.
2. Always use genuine Flymo Spare Parts.
3. Pre-packed spares are available from most Flymo approved stockists.

4. Your product is uniquely identified by a silver and black product rating label.

5. If you have a problem with your machine contact your local Approved Service Centre ensuring you have full details of your product as described on the product rating label.

6. Should it be necessary for work to be carried out by your Service Centre, it is important to take your complete machine including cable and any extension cables used.

A network of specialist dealers can be found in your local Yellow Pages. To obtain service on your product simply telephone or visit your local Service Centre. Should you require service under the terms of our guarantee the Service Centre will require proof of purchase. All of the centres listed stock genuine Flymo Spare Parts. NOTE: Our Service Repairers act on their own behalf and are not empowered to commit or legally bind Husqvarna UK Ltd. in any manner whatsoever.

5. STORAGE

At the end of the cutting season:

1. Clean your hedge trimmer thoroughly.
2. Check that all nuts and bolts are secure.
3. Visually inspect the hedge trimmer for any worn or damaged parts, contact your local Service Centre if any parts require replacement.

To store your hedge trimmer:

• Ensure the blade cover is fitted before storage.
• Store in a dry place where your hedge trimmer is protected from damage.

6. TROUBLESHOOTING

Fails to Operate:

1. Is the Power Turned On?
2. Check the fuse in the plug, if blown replace.
3. Fuse continues to blow? Immediately disconnect from the mains electricity supply and consult your local approved Service Centre.

Cutting blade stops under load:

1. Cut at a slower pace.
2. If cutting blade still stops under load? Disconnect from the mains electricity supply and consult your local approved Service Centre.

Fails to stop when one switch lever is released:

→ Immediately disconnect from the mains electricity supply and consult your local approved Service Centre.

Poor cut quality:

1. Ensure the product is being used correctly (see How to use your hedge trimmer).
2. Ensure blades are free from trapped debris.
3. Damaged Blades? Immediately disconnect from the mainselectricity supply and consult your local approved Service Centre.

Excessive Vibration:

→ Immediately disconnect from the mains electricity supply and consult your local approved Service Centre.

7. DISPOSAL (in accordance with RL2012/19/EC/S.I. 2013 No. 3113)

• Awareness of the environment must be considered when disposing of 'end-of-life' product.
• If necessary, contact your local authority for disposal information.

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the

recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more

detailed information about recycling of this product, please contact your local council office, your household waste disposal service or the shop where you purchased the product.

1. TECHNICAL DATA

Electric Hedge Trimmer	Unit Value	EasiCut 610XT
Blade length cm60
Power kW0.5
Measured Sound Power L_WA	dB(A)95
Guaranteed Sound Power L_WA	dB(A)98
Sound Pressure L_pA	dB(A)82.4
Uncertainty K_pA	dB(A)3.0
Hand/arm vibration a_h	m/s^2	3.05
Uncertainty K_vH	m/s^2	1.5
Weight kg4.1

Measuring process complying with: ^1) EN 60745-2-15 ^2) RL 2000/14/EC/S.I. 2001 No.1701

NOTE: The stated vibration emission value has been measured according to a standardized test procedure and can be used for comparison of one electric power tool with another. It can also be used for preliminary evaluation of expovibration emission value can vary during actual use of the electric power tool.

9. SERVICE/WARRANTY

Service:

Please contact the address on the back page.

Warranty statement:

In the event of a warranty claim, no charge is levied to you for the services provided.

Husqvarna UK Ltd. grants a warranty for all original FLYMO new products for two years from the date of original purchase from the retailer, provided that the devices have been for private use only. This manufacturer's warranty does not apply to products acquired second hand. This warranty includes all significant defects of the product that can be proved to be material or manufacturing faults. This war ranty is fulfilled by supplying a fully functional replacement product or by repairing the faulty product sent to us free of charge; we reserve the right to choose between these options. This service is subject to the following provisions:

• The product has been used for its intended purpose as per the recommendations in the operating instructions.
• Neither the purchaser nor a third party has attempted to open or repair the product.
• Only Original FLYMO replacement parts and wear parts have been used for operation.
  • Presentation of the receipt.

Normal wear and tear of parts and components (such as blades, blade fixing parts, turbines, light bulbs, V-belts / toothed belts, impellers, air filters, spark plugs), visual changes, wear parts and consumables are excluded from the warranty.

This manufacturer's warranty is limited to replacement and repair of products in accordance with the abovementioned conditions. The manufacturer's warranty does not constitute an entitlement to lodge other claims against us as a manufacturer, such as for damages. This manufacturer's warranty does not, of course, affect statutory and contractual warranty claims against the dealer / retailer.

The manufacturer's warranty is governed by the law of the Federal Republic of Germany.

In case of a warranty claim, please return the faulty product, together with a copy of the receipt and a description of the fault, with postage paid to the service address.

Consumables:

The blade and excentric drive are consumables and are not included in the guarantee.

PRODUCT LIABILITY

In accordance with the German Product Liability Act, we hereby expressly declare that we accept no liability for damage incurred from our products where said products have not been properly repaired by a FLYMO-approved service partner or where original FLYMO parts or parts authorised by FLYMO were not used.

EC DECLARATION OF CONFORMITY

The undersigned hereby certifies as the authorized representative of the manufacturer, Husqvarna AB, 561 82 Huskvarna, Sweden, that, when leaving our factory, the unit(s) indicated below is/are in accordance with the harmonised EU guidelines, EU standards of safety and product specific standards. This certificate becomes void if the unit(s) is / are modified without our approval.

Description of the product:	Hedge Trimmer EasiCut
Product type:	610XT
Article-Number:	9671030-xx
CE-Directives:	2006/42/EC2011/65/EU2014/30/EU2000/14/EC
Harmonised EN:	EN ISO 12100EN 60745-1EN 60745-2-15
Deposited Documentation:	GARDENA Technical Documentation,M. Jäger, 89079 Ulm
Conformity Assessment according to:	According to 2000/14/EG: Art. 14 Annex V
Noise level: measured / guaranteed	95 dB(A) / 98 dB(A)
Ulm, 18.08.2021Authorised representative:	Reinhard PompeVice President Products	Wolfgang EngelhardtVice President Supply Chain

UKCA DECLARATION OF CONFORMITY (ONLY FOR UK)

The manufacturer: Husqvarna AB SE 561 82 Huskvarna, Sweden hereby certifies, when leaving our factory, the unit(s) indicated below is/are in accordance with the UK Regulations, designated standards of safety and product specific designated standards. This certificate becomes void if the units are modified without our approval.

Description of the Product:	Hedge Trimmer EasiCut
Product type:	610XT
Article Number:	9671030-xx
UK regulations:	S.I. 2008/1597S.I. 2012/3032S.I. 2016/1091S.I. 2001/1701
Designated Standards:	EN ISO 12100EN 62841-1EN 62841-4-2EN 60745-1EN 60745-2-15EN ISO 10517
Authorised Representative:	Husqvarna UK Limited
Deposited Documentation:	Preston Road,Aycliffe,County DurhamUKDL5 6 UP
Noise level: measured / guaranteed	95 dB(A) / 98 dB(A)
Conformity Assessment according to:	According to S.I. 2001/1701	Art. 11 Schedule 8
Aycliffe, 18.08.2021Authorised Representative:	John ThompsonDirector

Service Address and Importer to

Great Britain

Husqvarna UK Ltd

Preston Road

Aycliffe Industrial Park

Newton Aycliffe

County Durham

DL5 6UP

Phone:[phone]

[e-mail]

Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice. Copyright © 2021 Flymo S.A. All rights reserved.

Flymo ^® and other product and feature names are registered or unregistered trademarks of Flymo S.A.

31610-85.960.01/0921

Husqvarna AB

S-561 82 Huskvama

Sweden