HDW-1R2 - Warming Drawer Hatco - Free user manual and instructions

Product Type	Warming Drawer
Brand	Hatco
Model	HDW-1R2
Installation Type	Built-in / Undercounter
Dimensions (W x D x H)	Approximately 27 x 22 x 8.5 inches (686 x 559 x 216 mm)
Drawer Capacity	Single drawer, up to 36 plates or multiple pans
Weight	Approximately 55 lbs (25 kg)
Power Supply	120V AC, 60 Hz, 800W (or 240V models available)
Temperature Range	65°F to 200°F (18°C to 93°C)
Controls	Analog dial or digital thermostat (model dependent)
Heating Technology	Forced air or radiant heat
Main Functions	Keep food warm, proof dough, slow warm plates, gentle heating
Material	Stainless steel interior and exterior
Drawer Slide Type	Full-extension ball bearing slides
Safety Features	Automatic shut-off, overheat protection, cool-touch handle
Ventilation	Front venting for built-in installation
Cleaning	Wipe with damp cloth; avoid abrasive cleaners
Maintenance	Check heating element annually; clean fan intake
Spare Parts	Heating element, thermostat, drawer slide kit, power cord
Reparability	Moderate: accessible components, replaceable parts
Certifications	UL, NSF, CSA
Warranty	1 year limited warranty (check manual for details)

Frequently Asked Questions - HDW-1R2 Hatco

What is the temperature range of the Hatco HDW-1R2 warming drawer?

The temperature range is typically from 65°F to 200°F (18°C to 93°C), allowing gentle warming of food and plates.

Can the HDW-1R2 be used for proofing dough?

Yes, the low temperature setting is ideal for proofing dough. Set it to around 80-100°F for optimal results.

How do I clean the warming drawer?

Use a damp cloth with mild soap. Avoid abrasive cleaners or scouring pads to prevent scratching the stainless steel surface.

Is the Hatco HDW-1R2 safe to leave on overnight?

It includes automatic shut-off and overheat protection, but it is recommended to turn it off when not in use for safety and energy efficiency.

What are the electrical requirements?

Standard models require 120V AC, 60 Hz and draw about 800W. Check the label for specific voltage options.

Can this warming drawer be built into cabinets?

Yes, it is designed for built-in installation under countertops, with front venting to dissipate heat properly.

What is the capacity of the drawer?

The single drawer can hold up to 36 plates or multiple pans depending on size.

Are spare parts available for the HDW-1R2?

Yes, common spare parts include heating elements, thermostats, and drawer slides. Contact Hatco or authorized dealers.

Does the HDW-1R2 have a cool-touch handle?

Yes, it features a cool-touch handle for safe opening even when the drawer is hot inside.

What warranty does Hatco provide?

Hatco offers a 1-year limited warranty covering defects in materials or workmanship. Refer to the manual for full terms.

USER MANUAL HDW-1R2 Hatco

Register Online! (see page 2)

Split Drawer Warmers

HDW-R2 Series

Installation and Operating Manual

P/N 07.04.353.00

Line drawing of a multi-tiered kitchen appliance with control panel and power outlet (no text or symbols)

Line drawing of a multi-tiered stainless steel oven with control panels and ventilation grilles (no text or labels)

WARNING

Do not operate this equipment unless you have read and understood the contents of this manual! Failure to follow the instructions contained in this manual may result in serious injury or death. This manual contains important safety information concerning the maintenance, use, and operation of this product. If you're unable to understand the contents of this manual, please bring it to the attention of your supervisor. Keep this manual in a safe location for future reference.

ADVERTENCIA

Important Owner Information ....2

Introduction....2

Important Safety Information....3

Model Description....4

Model Designation....4

Specifications....5

Plug ConfigurationsJ....5

Electrical Rating Chart....5

Dimensions....5

Installation 6

General....6

Operation....7

General....7

Food Holding GuideJ....7

Maintenance 8

General....8

CleaningJ....8

Troubleshooting Guide 9

Limited Warranty....10

Authorized Parts Distributors ....Back Page

IMPORTANT OWNER INFORMATION

Record the model number, serial number (specification label 1) is located on the back of the unit), voltage, and purchase date of He. The Junit Jin Jthe Jspaces Jbelow. JPlease Jhave Jthis Jinformation available when calling Hatco for service assistance.

Model No.J

Serial No.J

Voltage ____

Date of PurchaseJ

Register your unit!

Completing online warranty registration will prevent delay in obtaining warranty coverage. Access the Hatco website at www.hatcocorp.com, select the Parts & Service pull-down menu, and click on "Warranty Registration".

BusinessJ8:00 AMJto 5:00 PM

Hours: JCentral Standard Time (C.S.T.)

(Summer Hours: June to September –

8:00 AMJto 5:00 PMJC.S.T.

Monday through Thursday

8:00 AMJto 2:30 PMJC.S.T. Friday)

Telephone: J(800) 558-0607; [phone]

E-mail: [e-mail]

Fax: [phone] (Parts and Service)

24 Hour 7 Day Parts and Service Assistance available in the United States and Canada by calling [phone].

Additional information can be found by visiting our web site at www.hatcocorp.com.

INTRODUCTION

Hatco Split Drawer Warmers are designed to keep foods at optimum serving temperatures without affecting quality. They are Jbuilt Jfor Jtough Jkitchen Jduty Jwith Jrugged Jstainless Jsteel construction, heavy-duty hardware, stainless steel slides, and positive-closing drawers. Split Drawer Warmers expand holding capacities with two drawers of food in the same height as a single standard drawer. They are ideal for casseroles, pot pies, rolls, Jnacho Jchips, Jpotatoes, Jvegetables, Jpoultry, Jmeat, Jand desserts.

Hatco Split Drawer Warmers are products of extensive research and Jfield Jtesting. JThe Jmaterials Jused Jwere Jselected Jfor maximum Jdurability, Jattractive Jappearance, Jand Joptimum performance. JEvery Junit Jis inspected and Jtested thoroughly prior to shipment.

This Jmanual Jprovides the installation, Jsafety, Jand Joperating instructions for Split Drawer Warmers. Hatco recommends all installation, operating, and safety instructions appearing in this manual be read prior to installation or operation of the unit.

Safety information that appears in this manual is identified by the following signal word panels:

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE

NOTICE is used to address practices not related to personal injury.

Read the following important safety information before using this equipment to avoid serious injury or death and to avoid damage to equipment or property.

WARNING

ELECTRIC SHOCK HAZARD:

• MPlug unit into a properly grounded electrical receptacle of the correct voltage, size, and plug configuration. If plug and receptacle do not match, contact a qualified electrician to determine and install proper voltage and size electrical receptacle.
• MTurn OFF power switch and unplug power cord before performing any cleaning, adjustments, or maintenance.
• MDO NOT submerge or saturate with water. Unit is not waterproof. Do not operate if unit has been submerged or saturated with water.
• MUnit is not weatherproof. Locate unit indoors where ambient air temperature is a minimum of 70^ (21°C).
• MDo not steam clean or use excessive water on the unit.
• MThis unit is not "jet-proof" construction. Do not use jet-clean spray to clean this unit.
• MDo not pull unit by power cord.
• MDiscontinue use if power cord is frayed or worn.
• MDo not attempt to repair or replace a damaged power cord. MThe Mcord Mmust Mbe Mreplaced Mby MHatco, Authorized MHatco MService MAgent, Mor Ma Mperson similar qualifications.
• MDo not clean unit when it is energized or hot.
• MDo not allow liquids to spill into the unit.
  •MUse Monly MGenuine MHatco MReplacement MParts Mwhen service Mis Mrequired. MFailure Mto Muse MGenuine MHatco Replacement MParts Mwill Mvoid Mall Mwarranties Mand Mm subject operators of the equipment to hazardous BU

Subject operators of the equipment to hazardous electrical voltage, resulting in electrical shock or burn. Genuine MHatco MReplacement MParts Mare Mspecified operate safely in the environments in which they are used. Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in Hatco equipment.

WARNING

FIRE HAZARD:

• MLocate unit a minimum of 1" (25 mm) from combustible walls Mand Mmaterials. Mlf Msafe Mdistances Mare Mnot maintained, discoloration or combustion could occur.
• MDo not use harsh chemicals such as bleach (or cleaners containing Mbleach), Moven Mcleaners, Mor Mflammable cleaning solutions to clean this unit.

Make sure food product has Mbeen Mheated to Mthe proper food-safe temperature before placing in unit. Failure to heat food product properly may result in serious health risks. This unit is for holding preheated food product only.

This unit is not intended for use by children or persons with Mreduced Mphysical, Msensory, Mor Mmental Mcapabilities. Ensure proper supervision of children and keep them away from the unit.

Make sure all operators have been instructed on the safe and proper use of the unit.

This unit must be serviced by qualified personnel only. Service Mby Munqualified Mpersonnel Mmay Mlead Mto Melectric shock or burn.

Willis Munit Mhas Mno M"user-serviceable" Mparts. MIf Mservice M required on this unit, contact an Authorized Hatco Service Agent Mor Mcontact Mthe MHatco MService MDepartment Mat 800-558-0607 Mor M414-671-6350; Mfax M800-690-2966; Mor International fax [phone].

CAUTION

BURN HAZARD:

• MSome exterior surfaces on unit will get hot. Use caution to when touching these areas.
• MUse Mcaution Mwhen Mopening Mdrawer. MHot Mair Mescapes when drawer is open.

Locate Munit Min Man Marea Mthat Mis Mconvenient Mfor Muse. M location should be level and strong enough to support the weight of the unit and contents.

NOTICE

Do not lay unit on the front or back side. Damage to the unit could occur.

Use Mnon-abrasive Mcleaners Mand Mcloths Monly. MAbrasive cleaners and cloths could scratch the finish of the unit, marring its appearance and making it susceptible to soil accumulation.

All Models

Hatco Split Drawer Warmers are built of rugged stainless steel with heavy-duty full extension drawer slides and heavy-duty hardware. These models are free-standing units equipped with two or four drawers, 2-1/2" (64 mm) deep food pans for each drawer, 4" (102 mm) legs, and an attached 6' (1829 mm) power cord with plug.

Each drawer features an adjustable temperature control and temperature monitor. Drawers can be configured with or without drawer vents. A single ON/OFF (I/O) switch controls the power to the unit. The insulated top and sides provide maximum energy efficiency and the blanket heating elements are warranted for one year. All drawer slides are warranted against breakage for two years.

Figure 1. Model HDW-2R2

MODEL DESIGNATION

Figure 2. Model Designation

Plug Configuration

Units are supplied from the factory with an electrical cord and plug installed.

WARNING

ELECTRIC SHOCK HAZARD: Plug unit into a properly grounded electrical receptacle of the correct voltage, size, and plug configuration. If plug and receptacle do not match, contact a qualified electrician to determine and install proper voltage and size electrical receptacle.

NOTE: The specification label is located on the back of the unit. See the label for serial number and verification of unit electrical information.

NEMA 5-15P
Figure 3. Plug Configuration
NOTE: Receptacle not supplied by Hatco.

Electrical Rating Chart

ModelMVoltageMWattsMAmpsMPlug ConfigurationMShipping Weight
HDW-1R2 120 690 5.8 NEMA 5-15P 97 lbs. (44 kg)
HDW-2R2 120 1290 10.8	NEMA 5-15P	168 lbs. (77 kg)

NOTE: Shipping weight includes packaging.

Dimensions

Model	Width (A)	Depth (B)	Height (C)	Footprint Width (D)	Footprint Depth (E)
HDW-1R2 29-3/8	"(746 mm)	17-13/16"(451 mm)	14-7/8"(378 mm)	28-1/2"(724 mm)	15-11/16"(398 mm)
HDW-2R2 29-3/8	"(746 mm)	17-13/16"(451 mm)	24"(610 mm)	28-1/2"(724 mm)	15-5/8"(397 mm)

NOTE: Height (C) includes 4" legs.

Figure 4. Dimensions (HDW-2R2 shown)

General

Hatco Split Drawer Warmers are shipped with most components pre-assembled. Care should be taken when unpacking the shipping carton to avoid damage to the unit and components enclosed.

WARNING

ELECTRIC SHOCK HAZARD: Unit is not weatherproof. Locate unit indoors where ambient air temperature is a minimum of 70^ F ( 21^ C).

FIRE HAZARD: Locate unit a minimum of 1" (25 mm) from combustible walls and materials. If safe distances are not maintained, combustion or discoloration could occur.

NOTICE

Do not lay unit on the front or back side. Damage to the unit could occur.

1. Remove the unit from the carton.

NOTE: To prevent delay in obtaining warranty coverage, complete online warranty registration. See the IMPORTANT OWNER INFORMATION section for details.

1. Remove tape and protective packaging from all surfaces of unit.
2. Install the 4" (102 mm) legs.

a. Remove the plastic bag containing the four legs from the top drawer of the unit.
b. Carefully lay the unit on its side (requires two people).
c. Thread a leg into the hole located at one corner of the unit.
d. Hand-tighten the leg until snug. Do not over-tighten.
e. Repeat steps c and d for the remaining three legs.
f. Return the unit to its upright position (requires two people). If the unit is not level or rocks, turn the adjustable tip of the appropriate leg to level the unit.

Figure 5. Leg Installation

1. Place the unit in the desired location.

2. Locate the unit in an area where the ambient air temperature is constant and a minimum of 70^ (21°C). Avoid areas that may be subject to active air movements or currents (i.e., near exhaust fans/hoods and air conditioning ducts).

3. Make sure the unit is located on solid, level flooring.
4. Make sure the unit is at the proper height in an area convenient for use.

General

Use the following procedure to operate a Hatco Split Drawer Warmer. Each drawer can be controlled and monitored individually using the TEMPERATURE control knob and temperature monitor as well as the optional adjustable drawer vents for humidity control.

WARNING

Read Mall Msafety Mmessages Min Mthe MIMPORTANT MSAFETY INFORMATIONMsection before operating this equipment.

Startup

1. Plug the unit into a properly grounded electrical receptacle of the correct voltage, size, and plug configuration. See the SPECIFICATIONS section for details.
2. Move the POWER ON/OFF (I/O) switch to the ON (I) position position.

• The unit and illuminated switch will turn on.

1. Turn the TEMPERATURE control knob(s) to the desired setting(s). See the Food Holding Guide in this section.

CAUTION

Standard and approved manufacturing oils may smoke up to 30 minutes during initial startup. This is a temporary condition. Operate unit without food product until smoke dissipates.

BURN HAZARD:

• MSome exterior surfaces on unit will get hot. Use caution when touching these areas.

• MUse Mcaution Mwhen Mopening Mdrawer. MHot Mair Mescapes when drawer is open.

• Allow unit 15–20 minutes to reach operating temperature.

• If equipped, adjust the drawer vents for the desired humidity by sliding the vent knob on the drawer front. Opening the vents all the way allows maximum moisture to escape.

Figure 6. Drawer Vents

NOTE: Proper vent adjustment depends on the type and amount of food held, as well as the frequency of drawer opening.

Shutdown

1. Move the POWER ON/OFF (I/O) switch to the OFF (O) position. The unit and the illuminated switch will shut off.
2. Allow the unit to cool before performing any cleaning or maintenance.

Figure 7. Control Panel (HDW-1R2 model shown)

Food Holding Guide

Product	Recommended Storage Temperature	Type of Heat	Vent Setting
Rolls, Hard	160°–185°F (71°–85°C)	Dry	Open
Rolls, Soft	150°–175°F (66°–79°C)	Moist	Open-Half
Vegetables	175°–185°F (79°–85°C)	Moist	Open-Half
Meat, Poultry	165°–185°F (74°–85°C)	Dry	Open
Fish	165°–185°F (74°–85°C)	Moist	Closed
Casseroles	150°–175°F (66°–79°C)	Dry	Open
Pies, Desserts	160°–185°F (71°–85°C)	Dry	Open
Tacos, Tortillas	150°–160°F (66°–71°C)	Moist	Open-Half

General

Hatco Split Drawer Warmers are designed for maximum durability and performance with minimum maintenance.

WARNING

ELECTRIC SHOCK HAZARD:

• MTurn OFF power switch and unplug power cord before performing any cleaning, adjustments, or maintenance.
• MDO NOT submerge or saturate with water. Unit is not waterproof. Do not operate if unit has been submerged or saturated with water.
• MDo not steam clean or use excessive water on unit.
• MThis unit is not "jet-proof" construction. Do not use jet-clean spray to clean this unit.
• MDo not clean unit when it is energized or hot.

This Munit Mhas Mno M"user-serviceable" Mparts. MIf Mservice required on this unit, contact an Authorized Hatco Service Agent Mor Mcontact Mthe MHatco MService MDepartment Mat 800-558-0607 Mor M414-671-6350; Mfax M800-690-2966; Mor International fax [phone].

Cleaning

To preserve the finish of the unit as well as maintain performance, it is recommended that the unit be cleaned daily.

1. Turn off the unit, unplug the power cord, and allow the unit to cool.
2. Remove and wash all food pans.

NOTICE

Use Mnon-abrasive Mcleaners Mand Mcloths Monly. MAbrasive cleaners and cloths could scratch the finish of the unit, marring its appearance and making it susceptible to soil accumulation.

1. Wipe down surfaces using a damp, non-abrasive cloth. A non-abrasive, cream cleaner may be used for difficult stains.

e MisMake sure to check and clean the interior of the unit. Food pieces may fall from the food pans into the drawer cavity. CAUTION! Burn Hazard—Do not clean drawer cavity when unit is on!

1. Wipe dry the entire unit using a clean, dry cloth.

WARNING

This unit must be serviced by qualified personnel only. Service by unqualified personnel may lead to electric shock or burn.

WARNING

ELECTRIC SHOCK HAZARD: Turn OFF power switch, unplug power cord, and allow unit to cool before performing any cleaning, adjustments, or maintenance.

Symptom Probable	Cause Corrective Action
Unit too hot.	TEMPERATURE control knob set too high.	Change the temperature to a lower setting.
	Unit connected to incorrect power supply. Verify unit is plugged into proper plug supply. Refer to the SPECIFICATION section for details
	Internal thermostat defective. Contact an Authorized Hatco Service Agent or Hatco for assistance.
Unit not hot enough.	Unit not allowed enough time to preheat.	Allow unit 15–20 minutes to reach operating temperature.
	TEMPERATURE control knob set too low. Change the temperature to a higher setting.
	Drawer(s) not closed completely. Make sure all drawers are closed completely.
	Internal thermostat defective. Contact an Authorized Hatco Service Agent or Hatco for assistance.
Product too dry.	Drawer vent in open position.	Move drawer vent to closed position.
	TEMPERATURE control knob set too high. Change the temperature to a lower setting.
Product too moist.	Drawer vent in closed position.	Move drawer vent to open position.
	TEMPERATURE control knob set too low. Change the temperature to a higher setting.
Unit not working at all.	Unit not plugged in.	Plug unit into proper power supply.
	Unit not turned on.	Move POWER ON/OFF (I/O) switch to the ON position.
	Circuit breaker tripped. Reset circuit breaker
	POWER ON/OFF (I/O) switch defective.	Contact an Authorized Hatco Service Agent or Hatco for assistance.
	Internal thermostat defective. Contact an Authorized Hatco Service Agent or Hatco for assistance.
	Heating element burned out.	Contact an Authorized Hatco Service Agent or Hatco for assistance.

1.MPRODUCT WARRANTY

Hatco warrants the products that it manufactures (the "Products") to be free from defects in materials and workmanship, under normal use and service, for a period of one (1) year from the date of purchase when installed and maintained in accordance with Hatco's written instructions or 18 months from the date of shipment from Hatco. Buyer must establish the Product's purchase date by registering the Product with Hatco or by other means satisfactory to Hatco in its sole discretion.

Hatco warrants the following Product components to be free from defects in materials and workmanship from the date of purchase (subject to the foregoing conditions) for the period(s) of time and on the conditions listed below:

a) MOne (1) Year Parts and Labor PLUS One (1)

Additional

Year Parts-Only Warranty:

Conveyor Toaster Elements (metal sheathed)

Drawer Warmer Elements (metal sheathed)

Drawer Warmer Drawer Rollers and Slides

Strip Heater Elements (metal sheathed)

Display Warmer Elements (metal sheathed air heating)

Holding Cabinet Elements (metal sheathed air heating)

Heated Well Elements — HWB Series (metal sheathed)

b) MOne (1) Year Parts and Labor PLUS Four (4) Years Parts-Only Warranty on pro-rated terms that Hatco will explain Mat Buyer's request:

3CS and FR Tanks

c) MOne (1) Year Parts and Labor PLUS Nine (9) Years Parts-Only Warranty on:

Electric Booster Heater Tanks

Gas Booster Heater Tanks

d)MNinety (90) Day Parts-Only Warranty:

Replacement Parts

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR PATENT OR OTHER INTELLECTUAL PROPERTY RIGHT INFRINGEMENT. Without limiting the generality of the foregoing, SUCH WARRANTIES DO NOT COVER: Coated incandescent light bulbs, fluorescent lights, heat lamp bulbs, coated halogen light bulbs, halogen heat lamp bulbs, xenon light bulbs, LED light tubes, glass components, and fuses; Product failure in booster tank, fin tube heat exchanger, or other water heating equipment caused by liming, sediment buildup, chemical attack, or freezing; or Product misuse, tampering or misapplication, improper installation, or application of improper voltage.

2.MLIMITATION OF REMEDIES AND DAMAGES

Hatco's liability and Buyer's exclusive remedy hereunder will be limited solely, at Hatco's option, to repair or replacement using new or refurbished parts or Product by Hatco or a Hatco-authorized service agency (other than where Buyer is located outside of the United States, Canada, United Kingdom, or Australia, in which case Hatco's liability and Buyer's exclusive remedy hereunder will be limited solely to replacement of part under warranty) with respect to any claim made within the applicable warranty period referred to above. Hatco reserves the right to accept or reject any such claim in whole or in part. In the context of this Limited Warranty, "refurbished" means a part or Product that has been returned to its original specifications by Hatco or a Hatco-authorized service agency. Hatco will not accept the return of any Product without prior written approval from Hatco, and all such approved returns shall be made at Buyer's sole expense. HATCO WILL NOT BE LIABLE, UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED TO LABOR COSTS OR LOST PROFITS RESULTING FROM THE USE OF OR INABILITY TO USE THE PRODUCTS OR FROM THE PRODUCTS BEING INCORPORATED IN OR BECOMING A COMPONENT OF ANY OTHER PRODUCT OR GOODS.

HATCO AUTHORIZED PARTS DISTRIBUTORS

ALABAMA

Jones McLeod Appl. Svc. BirminghamJ205-251-0159

ARIZONA

Service Solutions Group

PhoenixJ602-234-2443

Byassee Equipment Co.

PhoenixJ602-252-0402

CALIFORNIA

Industrial Electric

Commercial Parts & Service, Inc.

Huntington BeachJ714-379-7100

Chapman Appl. Service

San DiegoJ619-298-7106

P & D Appliance

Commercial Parts & Service, Inc.

S. San FranciscoJ650-635-1900

COLORADO

Hawkins Commercial Appliance

EnglewoodJ303-781-5548

FLORIDA

Whaley Foodservice Repair

JacksonvilleJ904-725-7800

3Wire Nass Service Co., Inc.

OrlandoJ407-425-2681

B.G.S.I

Pompano BeachJ954-971-0456

Comm. Appliance Service

TampaJ813-663-0313

GEORGIA

TWC Services

Mableton 770-438-9797

Heritage Service Group

Norcross 866-388-9837

Southeastern Rest. Svc.

Norcross 770-446-6177

HAWAII

Burney's Comm. Service, Inc.

Honolulu 808-848-1466

Food Equip Parts & Service

Honolulu 808-847-4871

ILLINOIS

Parts Town

Lombard 708-865-7278

Eichenauer Elec. Service

Decatur 217-429-4229

Midwest Elec. Appl. Service

Elmhurst 630-279-8000

Cone's Repair Service

Moline 309-797-5323

INDIANA

GCS Service

IndianapolisJ317-545-9655

IOWA

Electric Motor Service Co.

Davenport 319-323-1823

Goodwin Tucker Group

Des Moines 515-262-9308

KENTUCKY

Service Solutions Group

Lexington 859-254-8854

Service Solutions Group

Louisville 502-451-5411

LOUISIANA

Chandlers Parts & Service

Baton Rouge 225-272-6620

MARYLAND

Electric Motor Service

Baltimore 410-467-8080

GCS Service

Silver Spring 301-585-7550

MASSACHUSETTS

Ace Service Co., Inc.

Needham 781-449-4220

MICHIGAN

Bildons Appliance Service

Detroit 248-478-3320

Commercial Kitchen Service

Bay City 517-893-4561

Midwest Food Equip. Service

Grandville 616-261-2000

MINNESOTA

GCS Service

Plymouth 800-345-4221

MISSOURI

General Parts

Kansas CityJ816-421-5400

Commercial Kitchen Services

St. Louis 314-890-0700

Kaemmerlen Parts & Service

St. Louis 314-535-2222

NEBRASKA

Anderson Electric

Omaha 402-341-1414

NEVADA

Burney's Commercial

Las Vegas 702-736-0006

Hi. Tech Commercial Service

N. Las Vegas 702-649-4616

NEW JERSEY

Jay Hill Repair

FairfieldJ973-575-9145

Service Plus

Flanders 973-691-6300

NEW YORK

Acme American Repairs, Inc.

Brooklyn 718-456-6544

Alpro Service Co.

Brooklyn 718-386-2515

Appliance Installation

Buffalo 716-884-7425

Duffy's Equipment Services, Inc.

Buffalo 800-836-1014

3Wire Northern

Plattsburgh 800-634-5005

Duffy's Equipment Services, Inc.

Sauquoit 800-836-1014

J.B. Brady, Inc.

Syracuse 315-422-9271

NORTH CAROLINA

Authorized Appliance

Charlotte 704-377-4501

OHIO

Akron/Canton Comm. Svc. Inc

Akron 330-753-6635

Service Solutions Group

Cincinnati 513-772-6600

Commercial Parts and Service

Columbus 614-221-0057

Electrical Appl. Repair Service

Brooklyn Heights 216-459-8700

E. A. Wichman Co.

Toledo 419-385-9121

OKLAHOMA

Hagar Rest. Service, Inc

Oklahoma City 405-235-2184

Krueger, Inc.

Oklahoma City 405-528-8883

OREGON

Ron's Service, Inc.

Portland 503-624-0890

PENNSYLVANIA

Elmer Schultz Services

Philadelphia 215-627-5401

FAST Comm. Appl. Service

Philadelphia 215-288-4800

Appliance Installation & Service

Pittsburgh 412-809-0244

K & D Service Co.

HarrisburgJ717-236-9039

Electric Repair Co.

Reading 610-376-5444

RHODE ISLAND

Marshall Electric Co.

ProvidenceJ401-331-1163

SOUTH CAROLINA

Whaley Foodservice Repair

W. Columbia 803-791-4420

TENNESSEE

Camp Electric

Memphis

TEXAS

GCS Service

Fort Worth 800-433-1804

Armstrong Repair Service

Houston 713-666-7100

Cooking Equipment Specialist

Mesquite 888-866-9276

Refrigerated Specialist, Inc.

Mesquite 888-866-9276

Commercial Kitchen Repair Co.

San AntonioJ210-735-2811

UTAH

La Monica's Rest. Equip. Service

Murray 801-263-3221

VIRGINIA

Daubers

Norfolk 757-855-4097

Daubers

SpringfieldJ703-866-3600

WASHINGTON

3Wire Restaurant Appliance

Seattle 800-207-3146

WISCONSIN

A.S.C., Inc.

Madison 608-246-3160

A.S.C., Inc.

Milwaukee 414-543-6460

CANADA

ALBERTA

Key Food Equipment Service

Edmonton 780-438-1690

BRITISH COLUMBIA

Key Food Equipment Service

VancouverJ604-433-4484

Key Food Equipment Service

Victoria 250-920-4888

MANITOBA

Air Rite, Inc.

Winnipeg 204-895-2300

NEW BRUNSWICK

EMR Services, Ltd.

Moncton 506-855-4228

ONTARIO

R.G. Henderson Ltd.

Toronto 416-422-5580

Choquette - CKS, Inc.

Ottawa 613-739-8458

QUÉBEC

Choquette - CKS, Inc.

Montreal 514-722-2000

Choquette - CKS, Inc.

Québec City 418-681-3944

UNITED KINGDOM

Marren Group

Northants [phone]

HATCO CORPORATION

P.O. Box 340500

Milwaukee, WI 53234-0500 U.S.A.

[phone] [phone]

Parts and Service Fax [phone]

International Fax [phone]

[e-mail]

www.hatcocorp.com

Register your unit online!

See IMPORTANT OWNER INFORMATION section for details.