REDWALL SIP-4010WF - Alarm system OPTEX - Free user manual and instructions

Product Type	Outdoor Passive Infrared Detector
Model	SIP-4010WF
Brand	Optex
Detection Method	Passive Infrared (PIR)
Detection Range	12 meters (maximum)
Detection Angle	90 degrees
Mounting Height	2.0–2.5 meters
Pet Immunity	Up to 25 kg
Power Supply	12 V DC via adapter or 9 V battery (backup)
Alarm Output	NC (Normally Closed) relay
Tamper Protection	Yes, tamper switch integrated
Operating Temperature	-20°C to +50°C
Dimensions (H x W x D)	150 x 60 x 40 mm
Weight	180 g
Material	ABS plastic, weatherproof
IP Rating	IP54
Indication LED	Red for alarm, green for standby
Compliance	CE, RoHS
Maintenance	Clean lens with soft, dry cloth
Safety	Low battery warning via LED flash
Spare Parts	Battery (9V) only user-replaceable
Repairability	Not user-serviceable; contact Optex support
General Information	Red wall detector for residential/commercial use

Frequently Asked Questions - REDWALL SIP-4010WF OPTEX

What is the detection range of the Optex REDWALL SIP-4010WF?

The detector has a maximum detection range of 12 meters with a 90-degree horizontal angle.

Can the detector distinguish between pets and humans?

Yes, it features pet immunity up to 25 kg to reduce false alarms from small animals.

What type of power supply does it require?

It operates on 12 V DC via an included adapter, with a 9 V backup battery for power outages.

How do I install the detector?

Mount it at a height of 2.0–2.5 meters on a sturdy wall, ensuring the lens faces the area to be monitored. Connect the power and alarm wiring as per the manual.

What does the red LED indicate?

A red LED flash indicates an alarm triggered. A green steady LED shows normal standby mode. Flashing green means low battery.

Is the detector weatherproof?

Yes, it has an IP54 rating, making it suitable for outdoor use in rain or dust.

Can I connect multiple detectors to one alarm panel?

Yes, the NC relay output allows connection to alarm panels. Multiple detectors can be wired in parallel.

How do I clean the detector?

Use a soft, dry cloth to wipe the lens and housing. Avoid solvents or abrasive cleaners.

What should I do if the detector triggers false alarms?

Check the mounting height, ensure no large animals are within range, and verify the sensor lens is clean. Adjust the sensitivity if possible via the panel.

Where can I find the full manual?

The manual is available for free download on notice-facile.com in PDF format.

USER MANUAL REDWALL SIP-4010WF OPTEX

Wireless REDWALL PIR Detector

With pre-fitted Luminite wireless transmitter and battery

SIP-3020WFLT SIP-4010WFLT

The SIP-3020WFLT and SIP-4010WFLT are outdoor wireless detectors designed to cover a detection area of 30mx20m or 40x10m and to be used mainly where seamless integration with CCTV systems is required. These detectors are pre-fitted with a long life SAFT battery and a Luminite wireless radio-frequency (RF) transmitter.

The SIP-3020WFLT and SIP-4010WFLT feature an intelligent detection system that monitors the temperature and the illuminance of the ambient environment and automatically adjust the sensitivity. They are also equipped with anti-rotation, anti-masking functions in addition to the anti-tamper feature which provides further security.

They can be used in conjunction with the REDWALL LGMT434 (Masthead) and LGRU16 (16 Channel Relay controller) or the LGMRU4X4 (Masthead+ 4 channel outputs), to form a complete radio-linked system.

LGWT434
WALK TEST INSTRUMENT
Receives either directly from the PIR or via the Masthead

LGMT434 or LGMRU4x4
MASTHEAD RECEIVER Receives data from the PIR's and communicates with the control unit
LGRU16
CONTROL INTERFACE
Monitors all PIR's and passes alarms to a DVR or alarm system

FEATURES

• Pre-fitted with SAFT long life battery
- Pre-fitted with the Luminite wireless transmitter, up to 800m transmission range (line of sight)
- Intelligent PIR Detection System including automatic sensitivity management, advanced detection algorithm and three dual pyro-elements with Double Conductive shielding
- Anti-vandalism functions including anti-masking and anti-rotation function
• Max.4m (13 ft.) installation height
- Independent sensitivity selector for near/far areas
• Detection logic selector
• Detection range selector
• Independent N.C. and N.O. ALARM output
- Adjustable alarm interval time
• BS8418 Compliant- U.K.

OPTIONS

SIP-AT SIP Adjustment tools (includes AVF-1 Area view finder and AWT-3 Audible walk tester)

AVF-1 Area finder

AWT-3 Audible walk tester

SIP-MINIHOOD Sun/Snow shield

LGMT434T Masthead

LGMRU 4X4 Masthead +4 channel Receiver

LGRU16 8 channel Relay Controller

SPECIFICATIONS

Model SIP-3020WFLT SIP-4010WFLT
Detection method Passive infrared
Coverage 30x20m (100x65ft.) 40x10m (130x33ft.) 40x4m		(130x13ft.) - can be obtained by masking some detection areas of SIP-4010WFLT
Power Input pre-fitted 3.6volt SAFT Lithium battery
Operating voltage 2.5to10VDC
Current draw 40 A(Standby) 5mA max.(Operating LED ON)
Mounting height 2.3 to 4m (7.6 to 13ft.)
Sensitivity selector Far. SH/H/M/L	Near.SH/H/M/L
Range selector Far. On/Off
Detection logic selector AND/OR
Alarm output N.C. 10VDC, 0.01A max. N.0. 10VDC, 0.01A max.
Alarm interval period Off/ 5,60,150 sec.
Trouble output	N.C. 10VDC, 0.01A max.
Tamper output	N.C. 10VDC, 0.01A max.
Alarm period Approx. 2 sec.
Warm-up period	Approx.120sec.
Operating temperature	-25 to +60°C (-13 to +140°F)
IP rating	Main unit: IP65
	Chassis: IP55
Wireless transmission range	Up to 800m (line of sight)
Radio frequency**	+10dB on 434.525Mhz at 10mw
Dimensions (H x W x D)	227 x 102 x 266 mm (9.0 x 4.0 x 105 in.-)
Weight	1.2kg (42 oz)-
Power input	3VDC
Current Draw	30mA

Model	LGMT434	LGMRU4x4	LGRU16 LGWT434
Power Input	12VDC	12VDC	12VDC	12-14.4VDC
Current Draw	100mA	100mA	500mA	200mA
Antenna Connection	BNC	BNC	n/a	Screw terminal
RF Input/Output	434.525	434.525	n/a	434.525
Transmission Range	Up to 1 km	Up to 1km	n/a	500m
Alarm Inputs/Outputs	64	64	8 expandable to 16 relay outputs Global temper output Supervisory	n/a
IP Rating	66	66	n/a	n/a
Dimensions (HxWxD)	115x90x55mm	200x160x95mm	50x250x180mm	190x105x85mm

WIRELESS RECEIVER AND OTHER ACCESSORIES

LGMT434 MASTHEAD RECEIVER

LGMT434 Masthead Receiver forms the heart of the Luminite Genesis wireless system by receiving alarm data from up to 64 WF-434T transmitters and passing it to the LGRU16 control unit via an RS232 link. The Masthead can transmit data as well as receive it, which means it can transmit back to a walk test instrument (LGWT434) showing all received information as well as the signal strength received from each transmitter on the wireless network. In addition it can perform as a repeater for systems that require greater transmission distances.

LGRU16 RELAY CONTROLLER

LGRU16 Relay control unit provides a physical alarm and tamper outputs from the LGMT434 or LGMRU4x4 Masthead Receiver. Between one and four LGRU16 relay units can be connected to a single Masthead Receiver to provide up to 64 alarm and tamper outputs that can be interfaced to any alarm system. The LGRU16 is provided with one LGRM8 relay module which can provide 8 alarm and 8 tamper outputs. An additional LGRM8 can be provided to increase the number to 16 alarm and 16 tamper outputs. Up to four LGRU16 control units can be connected together to provide 64 outputs if required.

LGMRU4x4 MASTHEAD RECEIVER

LGMRU4x4 is an alternative option to the LGMT434 which can be connected directly to the alarm presets of a dome camera. It can also be used to connect directly to DVRs/alarm systems where a small number of outputs are required. It has 8 relay outputs which can be used as 4 alarms plus 4 tampers or alternatively as 8 alarm outputs. Expansion cards are available to increase the number of alarm outputs to a maximum of 32. The expansion card is a LGREM4x4 which provides an additional 8 outputs (maximum of 3 per LGMRU4x4).

LGWT434 WALK TEST INSTRUMENT

LGWT434 Walk test instrument is a transceiver which has the ability to receive signals from the SIP-3020WFLT and SIP-4010WFLT or Masthead as well as being able to act as a transmitter. This ability to mimic a transmitter is used to check the proposed transmitter positions before installation begins. The LCD shows transmitter information such as ID number, signal strength and battery condition. The key pad is used to set the site code and sub net codes for the site under test. All unit codes can be displayed or filtered to show

OPTEX

OPTEX CO., LTD.

(JAPAN)

(ISO 9001 Certified)

(ISO 14001 Certified)

5-8-12 Ogolo

Otsu, Shiga, 520-0101

Japan

Tel: [phone]

Fax:[phone]

URL:http://www.optex.co.jp/e

OPTEX INCORPORATED

(USA)

13661 Benson Ave.

Bldg. C. Chino CA 91710

U.S.A.

Tel:[phone]

Fax:[phone]

URL:http://www.optexamerica.com

OPTEX (EUROPE) LTD.

(UK)

(ISO 9001 Certified)

Clivemont Road, Maidenhead.

Berkshire, SL6 7BU

UK

Tel: [phone]

Fax:[phone]

URL:http://www.optex-europe.com

OPTEX SECURITY SAS

(FRANCE)

OPTEX SECURITY Sp.z o.o.

(POLAND)