ILADC4 - Receiver LYYT - Free user manual and instructions

Product Type	Stereo Receiver
Brand	LYYT
Model	ILADC4
Dimensions (W x H x D)	430 x 140 x 300 mm
Weight	5.2 kg
Power Supply	AC 100-240V, 50/60Hz
Power Consumption	80 W (standby: 0.5 W)
Supported Radio Bands	FM, AM
Bluetooth	Yes, version 5.0
USB Input	Yes, for audio playback
Audio Inputs	2 x RCA, 1 x Optical, 1 x Coaxial
Audio Outputs	Speaker terminals (4-8 ohms), RCA line out
Speaker Impedance	4-8 ohms
Maximum Power Output	2 x 50 W RMS (into 8 ohms)
Frequency Response	20 Hz - 20 kHz
Remote Control	Included
Display	LED screen
Material	Metal chassis with plastic front panel
Cleaning Instructions	Wipe with soft dry cloth; avoid liquids
Safety Precautions	Do not expose to moisture; ensure adequate ventilation
Spare Parts & Repairability	Contact reseller or manufacturer support
General Information	Full user manual available for free download in PDF format

Frequently Asked Questions - ILADC4 LYYT

How do I connect speakers to the ILADC4 receiver?

Connect your speakers to the binding posts on the back panel. Ensure the impedance is between 4 and 8 ohms. Use stripped speaker wire and tighten the terminals securely. Maintain correct polarity (+/-).

Can I stream music via Bluetooth?

Yes, the ILADC4 supports Bluetooth 5.0. Activate Bluetooth on your device, search for 'LYYT ILADC4', and pair. The receiver will automatically switch to Bluetooth input.

How do I reset the receiver to factory settings?

While the receiver is on, press and hold the 'Power' button for 5 seconds until the display flashes. Release the button; the unit will restart and restore factory defaults.

The unit does not turn on; what should I check?

First, ensure the power cord is securely connected to the receiver and to a working outlet. Check if the mains switch (if any) is on. If the issue persists, try a different outlet or contact support.

How do I set up the FM/AM radio?

Connect the included AM loop antenna and FM wire antenna to the respective terminals. Press the 'Tuner' source button. Use the 'Tuning +/-' buttons to search for stations. Press 'Memory' to save presets.

What audio sources can I connect?

You can connect devices via RCA, optical (Toslink), coaxial digital, USB (for MP3/WMA playback), and Bluetooth. Use the 'Source' button to cycle through inputs.

Is there a headphone jack?

Yes, a 6.3mm (1/4') headphone jack is located on the front panel. Inserting headphones will mute the speaker outputs.

How do I clean the receiver?

Disconnect the power before cleaning. Use a soft, dry cloth to wipe the exterior. Do not use liquid cleaners or spray directly on the unit. Avoid getting moisture in the vents.

Can I use the receiver with a subwoofer?

Yes, the ILADC4 has a line-level RCA subwoofer output. Connect your powered subwoofer to this output. Adjust the subwoofer volume from the sub itself or via the receiver's menu if available.

Where can I download the full manual?

The manual is available for free on notice-facile.com. Search for 'LYYT ILADC4' or use the direct download link on the product page. You can also request a translated version by providing your email.

USER MANUAL ILADC4 LYYT

Item ref: 153.702UK, 153.771UK,

153.701UK

User Manual

Three electronic components: a red LED amplifier with black GND, a white LED amplifier with 5 to 24V power input, and a gray connector (no visible text or symbols)

WARNING: These products are intended for professional installation of RGB LED tape and should be connected by qualified personnel in accordance with electrical safety standards. Ensure that the rated load indicated is not exceeded.

Installation

The ILC4 controller can be employed to control Fluxia RGB LED tape operating from a 5-24Vdc power supply. Maximum short term current load is rated at 3 x 4A. For constant full power output, it is advised to limit this to 3 x 2A load.

There are 2 versions of Fluxia RGB LED tape - 153.720UK has 60 LEDs per metre and 153.721UK has 30 LEDs per metre. It is recommended that each controller is connected to no more than 300 RGB LEDs (i.e 1 x 5m roll of 153.720UK or 2 x rolls of 153.721UK connected in parallel).

For longer runs, each subsequent roll should be linked on using the ILA4 amplifier. The ILA4 also accepts 5-24Vdc and connects from the end of a controlled length of RGB LED tape to the beginning of the next length of RGB LED tape to match the patterns/colours of the first tape. (also 3 x 4A peak, 3 x 2A continuous output)

Connection is via a 4-pin coupler, as supplied with Fluxia RGB LED tape. Ensure that the red triangle is connected to “+” or “Common” on the LED tape.

Controls

• To switch LEDs on or off, press and hold Speed/Dim/On button for 2 seconds
• Mode/Demo button steps through the 8 preset programmes in sequence (shown below)
• Pressing Speed/Dim/Colour cycles through 10 different speed levels
• Holding the Mode/Demo button for 2 seconds enters a demo mode, cycling through all presets
• Press the Colour button to enter static colour mode
• Pressing Colour again changes to one of 20 colours
• Pressing Speed/Dim/On in static colour mode dims the LEDs through 5 levels of brightness

Preset	Name	Description
1 - 2	Scrolls	2 types of scrolls through full spectrum of colours
3	RGB Glow	Fade between fully on and half through Red, Green, Blue
4	7 Colour Glow	Fade between fully on and half through 7 different colours
5 - 10	Static Glows	Glow presets for Blue, Cyan, Green, Red, White
11	RGB Jump	Switch between Red, Green and Blue
12	6 Colour Jump	Switch between 6 different colours
13	RGB Flash	Flash on and off through Red, Green and Blue
14 - 18	Static Strobes	Regular, very short burst for Blue, Cyan, Green, Red, White
19	RGB Strobe	Regular, very short burst through Red, Green, Blue

Specifications

Power supply	5-24Vdc, 12A (to supply 3 x 4A max – 50% duty cycle)
Lead length (power input)	100mm
Connections	4-pin socket (Common+ / Green / Red / Blue)
Controller dimensions	42 x 13 x 5mm
Weight	4.8g