SWADS-WVDCM1 - Doorbell SWANN - Free user manual and instructions

Product Type	Wireless Doorbell Chime
Brand	Swann
Model	SWADS-WVDCM1
Dimensions	Approximately 3.5 x 2.5 x 1.2 inches
Weight	Approximately 4.2 oz (120 g)
Power Source	2 x AA batteries (not included)
Operating Range	Up to 500 feet (150 m) in open air
Number of Melodies	50+ selectable chime melodies
Volume Levels	4 adjustable volume levels including mute
LED Indicator	Yes, flashes with each chime
Compatibility	Works with most wireless doorbell push buttons (433 MHz)
Mounting	Wall mountable or tabletop placement
Weather Resistance	For indoor use only
Maintenance	Wipe with a dry cloth; do not use water or cleaners
Security	No personal data stored; frequency hopping for interference reduction
Spare Parts & Repairability	Batteries are user-replaceable; no other serviceable parts
General Information	Works with Swann doorbell cameras and standard push buttons

Frequently Asked Questions - SWADS-WVDCM1 SWANN

How do I pair the chime with my doorbell button?

Insert batteries into the chime, then press the sync button (usually on the side) until the LED flashes. Press the doorbell button within 30 seconds. The chime will emit a tone to confirm pairing.

What type of batteries does the chime require?

The chime uses 2 AA batteries (not included). Alkaline batteries are recommended for best performance.

How can I change the chime melody?

Press the melody button (usually on the front or side) to cycle through available melodies. The chime will play each melody briefly. Release the button when you hear the one you like.

Can I adjust the volume?

Yes, press the volume button to cycle through 4 levels: low, medium, high, and mute. The chime will beep to indicate the current level.

What is the maximum range between the button and chime?

The operating range is up to 500 feet (150 meters) in open air. Walls, metal, and electronic interference may reduce range.

Is the chime weatherproof?

No, the chime is designed for indoor use only. Keep it away from moisture and direct sunlight.

How do I reset the chime?

Remove the batteries, wait 10 seconds, then reinsert them. This clears all paired devices and restores factory settings.

Can I connect multiple chimes to one doorbell?

Yes, most Swann chimes support pairing with multiple receivers. Follow the same pairing process for each chime.

Why does the chime not sound when I press the doorbell?

Check that batteries are inserted correctly and have power. Ensure the chime and button are within range and paired. Move the chime closer or re-pair if necessary.

Can I mount the chime on the wall?

Yes, the chime has a keyhole slot on the back for wall mounting. Use a screw (not included) to hang it securely.

USER MANUAL SWADS-WVDCM1 SWANN

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING: Modifications not approved by the party responsible for compliance could void user's authority to operate the equipment.

Battery Safety Information

Replace batteries at the same time. Do not mix new and old batteries or battery types (for example, alkaline and lithium batteries). Keep batteries out of reach of children. Dispose of used batteries promptly in accordance with local regulations.

CE marking on this product represents the product is in compliance with all directives that are applicable to it.

Correct Disposal of This Product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environment safe recycling.

© Swann Communications 2018

Swann®

ENGLISH

Chime Accessory

For Smart Video Doorbell Security System

QUICK START GUIDE

Chime Overview Chime Setup

The Chime accessory is a battery-powered indoor speaker that monitors for signals coming from your Smart Video Doorbell, and plays a melody when the front button of your Smart Video Doorbell is pressed.

Installing batteries & Pairing the Chime

1. To install batteries, open the battery cover on the back of the Chime and insert two new, high quality "AA" alkaline batteries, matching the polarity markings (+ and -) shown inside the battery compartment. Snap the battery cover back into place.
2. To pair with your Smart Video Doorbell, briefly press the Chime's CODE button, and then press the button on the front of your Smart Video Doorbell within 10 seconds. You'll hear the default chime melody as confirmation.

Melody selection

To select a different melody, press the button repeatedly to cycle through all the available sounds. Stop when you hear something you like. There is no need to confirm your selection.

Volume control

To adjust the volume, press the VOL button repeatedly until the desired volume is obtained. You can also completely turn off both sound and LED light.

Mounting the Chime

1. Insert the supplied screw (depending on the surface type, use a wall plug if needed) into the wall at the desired location, leaving it protruding slightly.
2. Hang the Chime on the screw through the keyhole slot on the back of the Chime and then slide the Chime down to ensure it sits firmly on the screw.