SH16310N - Heating SWAN - Free user manual and instructions

Brand	Swan
Model	SH16310N
Product Type	Column Patio Heater
Power Source	Electric (plug-in)
Assembly Required	Yes, two persons recommended
Included Components	Lower body, upper body, base, base cover, cord grip, screws, washers, joint boards, Allen key
Tools Required (not included)	Cross head screwdriver
Cord Grip Feature	Ensure lip faces upward when fastening
Usage Location	Outdoor patio (not for indoor use)
Height (estimated)	Approximately 1.8 m (column type)
Base Dimensions	Circular base, diameter approx. 40 cm
Weight (estimated)	Approximately 8 kg
Heating Element	Quartz or infrared (typical electric patio heater)
Power Rating (estimated)	1500-2000 W
Safety Features	Tip-over switch (typical), overheat protection
Cleaning	Wipe with a soft, dry cloth; do not use abrasive cleaners
Spare Parts Availability	Contact Swan customer service (0333 220 6050)
Manual Languages	English (PDF available for download)

Frequently Asked Questions - SH16310N SWAN

What tools are needed to assemble the Swan SH16310N patio heater?

You will need a cross head screwdriver (not included) and the provided Allen key. Assembly is much easier with two people.

How do I attach the base to the main unit?

Turn the unit upside down (use a cloth to prevent scratches), put the base inside the base cover, thread the plug and cord through the hole, then fasten the base using the provided screws and washers. Finally, fasten the cord grip with the lip facing upward.

Can I use this patio heater indoors?

No, this heater is designed for outdoor use only. Using it indoors can cause fire or carbon monoxide poisoning.

How do I clean the heater?

Allow the heater to cool completely. Wipe the exterior with a soft, dry cloth. Do not use abrasive cleaners or immerse in water.

What should I do if the cord grip doesn't hold the cable?

Ensure the lip of the cord grip is facing upward when you fasten it. If it still doesn't hold, check that the screws are properly tightened. If the issue persists, contact Swan customer service.

Is it normal for the heater to make noise when operating?

Some electrical or expansion noises are normal. If you hear loud or unusual sounds, turn off the heater and check for loose parts or contact support.

How do I replace a damaged heating element?

The heating element is not user-replaceable. Contact Swan customer service or a qualified technician for repairs.

What is the warranty period for the Swan SH16310N?

Warranty information is typically provided in the printed manual. For details, visit the Swan website or contact customer service at 0333 220 6050.

Can I leave the heater unattended while it is on?

No, never leave the heater unattended while in use. Always turn it off and unplug it when not in use.

Why is two-person assembly recommended?

The heater is tall and heavy. Two people make assembly safer and reduce the risk of damaging the product or causing injury.

USER MANUAL SH16310N SWAN

Patio Heaters Assembly Photo Guide

Models: SH16310N, SH16320N, SH16330N

Please read in conjunction with the printed manual that came with the product

Help line: 0333 220 6050

v1.0

SH16310N - COLUMN PATIO HEATER

1. Lower body
2. Upper body
3. Base
4. Base cover
5. Cord grip
6. Screws for joint boards
7. Screws & washers for base
8. Joint boards
9. Allen key

You will also need a cross head screw driver. Assembly is much easier with two people and reduces the risk of damaging the product.

2

Swan

SH16310N - COLUMN PATIO HEATER

Thread the plug and cable from the upper body (2) through the channel in the lower body (1)

Make sure it goes all the way through.

Slide the upper body (2) on to the lower body (1)

SH16310N - COLUMN PATIO HEATER

Fit the joint boards and secure with the screws (6) using the allen key provided (9)

Turn the unit upside down (put some cloth down to prevent scratches).

Put the base (3) inside the base cover (4) and thread the plug and cord through the hole in the middle

SH16310N - COLUMN PATIO HEATER

Fasten the base to the main unit using the screws & washers (7)

Fasten the cord grip (5). Make sure the lip faces upwards

Refer to the manual that came with the product for operation guide

wan

SH16320N - BAR TABLE PATIO HEATER

1. Main body
2. Base cover
3. Base
4. Table top
5. Foot bracket
6. Allen keys - 1 large + 1 small
7. Screws & washers for base
8. Long screws + steel tubes
9. Screws for table top

You will also need a cross head screw driver. Assembly is much easier with two people and reduces the risk of damaging the product.

6

Swan

SH16320N - BAR TABLE PATIO HEATER

Turn the main body (1) upside down (put a cloth down to prevent scratches)

Fit the base cover and thread the plug and cord through the hole in the middle.

Fit the base inside the base cover (2) and align the holes ready for the screws and washers.

7

Swan

SH16320N - BAR TABLE PATIO HEATER

Fit the screws and washers. Leave them slightly loose for the moment. This allows a little movement in the base for the next part...

Get someone to hold the bar base (5) in position.

Thread the long screws though the holes in to the steel tubes (8) and into the threaded holes on the bar base.

Don't fully tighten them until all 3 are fitted

SH16320N - BAR TABLE PATIO HEATER

Once all 3 of the long screws are fitted, tighten them all (using the larger allen key)

Finally tighten the base screws as well (small allen key)

Fit the cable to the cable tie and fit the castors

SH16320N - BAR TABLE PATIO HEATER

Turn the unit the right way up again & offer up the table top.

The holes must line up as shown. The bump (2) must align with the hole (1)

This MUST be a 2 person task or you risk breaking the table top.

Fit the screws to secure the table top to the main unit.

Refer to the manual that came with the product for operation guide

SH16330N - PORTABLE PATIO HEATER

1. Main body
2. Base cover
3. Base
4. Cord grip & screws
5. Allen key
6. Deco board
7. Base screws & washers

You will also need a cross head screw driver. Assembly is much easier with two people and reduces the risk of damaging the product.

11

Swan

SH16330N - PORTABLE PATIO HEATER

Fit the deco boards (6) as shown

Put the base (3) inside the base cover (2) and thread the plugs and cord through the hole in the middle.

Make sure the 2 mounting holes are aligned.

12

Swan

SH16330N - PORTABLE PATIO HEATER

Fit the base assem- bly to the main body

[1] and tighten the screws and washers [7] as shown.

Fit the cord grip (4) ensuring the lip faces upward.

Refer to the manual that came with the product for operation guide

www.swan-brand.co.uk

Scan this QR code to hear about our story

We love what we do

we're proud of our quality

Find us on Facebook

* on selected products

Copyright © Swan Products Ltd. PO Box 3117, Stoke-on-Trent ST4 9GD