ProLiant DL185 G5 - Server HP - Free user manual and instructions
Find the device manual for free ProLiant DL185 G5 HP in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Rackmount Server |
| Form Factor | 2U |
| Dimensions (W x D x H) | 448 x 733 x 87 mm (17.6 x 28.9 x 3.4 in) |
| Weight (maximum) | 28.5 kg (62.8 lb) |
| Power Supply | Dual redundant 800W hot-plug power supplies |
| Processor | Dual AMD Opteron 2300 Series |
| Chipset | NVIDIA nForce Professional 3600 |
| Memory | 16x DIMM slots, DDR2 ECC Registered, up to 128 GB |
| Internal Storage | Up to 12 hot-plug SATA/SAS drive bays (3.5-inch) |
| RAID Controller | HP Smart Array P400i (RAID 0/1/5/6) |
| Network | Dual Gigabit Ethernet (Broadcom BCM5708C) |
| Remote Management | HP iLO 2 (Integrated Lights-Out 2) |
| Expansion Slots | 2x PCI Express x8, 1x PCI Express x4 |
| USB Ports | 4x USB 2.0 (2 front, 2 back) |
| Video | Integrated ATI RN50 16MB |
| Operating Temperature | 5°C to 35°C (41°F to 95°F) |
| Operating Humidity | 10% to 90% non-condensing |
| Safety Compliance | UL, CE, FCC Class A |
| Maintenance & Cleaning | Use a soft, dry cloth; vacuum dust from vents periodically |
| Spare Parts & Repairability | Hot-plug drives, memory, and power supplies; replaceable fans and RAID battery |
Frequently Asked Questions - ProLiant DL185 G5 HP
How do I power on the HP ProLiant DL185 G5?
Press the power button on the front panel. Ensure the power cords are connected and the PSU switches (if present) are turned on.
How do I reset the server to factory defaults?
Press and hold the reset button (if available) or power cycle the system. To reset BIOS defaults, press F9 during POST and select 'Load Defaults'.
How do I access the BIOS setup?
Press F10 during POST to enter the BIOS setup utility. From there you can configure boot order, processor settings, and more.
How do I replace a failed hard drive?
Identify the failed drive by LED indicator. Press the release button, remove the carrier, install a new compatible drive, and insert the carrier. The RAID controller will automatically rebuild if configured.
How do I upgrade the memory?
Power down the server, remove the top cover, locate the DIMM slots. Populate slots in the correct order (see manual). Use DDR2 ECC Registered memory. Replace cover and power on.
How do I configure RAID?
During POST, press F8 to enter the HP Smart Array configuration utility. Create arrays, assign logical drives, and set RAID levels (0/1/5/6).
How do I update the firmware?
Download firmware from HP Support site. Use the HP Smart Update Manager or boot from a firmware CD. Alternatively, update via iLO 2 web interface.
How do I access the remote management interface?
Connect to the iLO 2 management port (dedicated Ethernet). Default IP is 192.168.0.120 (check manual). Open a web browser and log in with default credentials (admin/password).
What should I do if the server beeps continuously on startup?
Continuous beeps indicate a hardware error. Check the POST code or iLO logs. Common causes: memory not seated, CPU failure, or power supply issue.
How do I clean the server?
Power off and unplug. Use a can of compressed air to blow out dust from fans and vents. Wipe exterior with a soft, dry cloth. Do not use liquids.
User questions about ProLiant DL185 G5 HP
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual ProLiant DL185 G5 - HP and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ProLiant DL185 G5 by HP.