ASF 950 - Household Fan Andrews - Free user manual and instructions

Product Type	Household Fan
Brand	Andrews
Model	ASF 950
Dimensions (approx)	400 x 400 x 140 mm
Weight	2.5 kg
Power Supply	220-240 V, 50/60 Hz
Power Consumption	45-60 W
Fan Speed Settings	3 speeds (Low, Medium, High)
Oscillation	Yes, wide angle
Adjustable Tilt	Yes, manual tilt adjustment
Remote Control	Yes, infrared
Timer	1-7 hours
Material	ABS plastic
Safety Features	Overheat protection, tip-over switch
Maintenance	Clean grille with damp cloth; avoid dust accumulation on motor
Reparability	Spare parts available (blade, motor, remote)
Noise Level	35-55 dB
Airflow	1600 m³/h (typical)
Warranty	1 year (manufacturer)
Package Includes	Fan, remote control, user manual
Color	White

Frequently Asked Questions - ASF 950 Andrews

How do I clean the fan?

Unplug the fan before cleaning. Use a damp cloth to wipe the grille and body. Do not immerse in water. Use a soft brush to remove dust from the motor area.

Does the remote control require batteries?

Yes, the remote control uses 2 AAA batteries (not included). Replace them when the range decreases.

How do I activate oscillation?

Press the oscillation button on the remote or control panel. A light will indicate oscillation active. Press again to stop.

What is the noise level of the fan?

The noise level ranges from 35 dB (low speed) to 55 dB (high speed). It is quiet enough for bedroom use on low.

How do I set the timer?

Press the timer button repeatedly to set desired hours (1-7). The fan will automatically turn off after the set time.

Is the fan energy efficient?

Yes, with a power consumption of 45-60 W, it is energy efficient compared to air conditioning. Use low speed for less power.

What should I do if the fan stops working?

Check if it is plugged in and the tip-over switch is properly engaged. If the motor overheats, let it cool for 30 minutes before restarting. If the problem persists, contact support.

Can I use the fan outdoors?

No, this fan is designed for indoor use only. Keep away from moisture and direct sunlight.

How do I store the fan during winter?

Clean the fan thoroughly, wrap it in a plastic cover or box, and store in a dry place. Remove batteries from remote to prevent leakage.

Are spare parts available for the ASF 950?

Yes, replacement blades, motors, and remotes can be ordered from Andrews service centers or authorized retailers. Refer to user manual for part numbers.

USER MANUAL ASF 950 Andrews

Blue industrial fan with black blades mounted on a wheeled cart (no visible text or symbols)

Operating Instructions & Safety Guide

ANDREWS

VENTILATION

0800 211 611

andrews-sykes.com

General Safety

Electric Ventilation Fans are for internal use only.
This equipment should only be used by a competent person who has read and understood these instructions.
Check condition of equipment before use. If unit is showing any signs of damage contact your supplier immediately.
Never operate this equipment if you are ill, feeling tired or under the influence of alcohol or drugs.
Do not use in wet or damp conditions.
- Keep all vents and grilles clear of obstructions.
- Keep children and animals away from electric appliances.
Never leave them alone in room where the units in use.
Make sure equipment is switched off and unplugged after use.

Electrical Safety

230 volt units require a standard domestic 13 amp socket.
110 volt units require a 32 amp BS 4343 power supply
Always inspect plugs and power cables for damage before plugging into power supply.
DO NOT USE IF ANY DAMAGE IS FOUND.
- Ensure cables are installed so as not to cause a hazard.
If an extension lead is used, ensure it is of the correct standard and fully uncoiled before use.
Cables must not be laid in wet or damp areas.
Do not move equipment while operating.
Do not pull equipment by the power lead.
It is recommended that the electrical supply to this equipment is protected by an RCD.

Getting started and operation

Position equipment on level ground

Fig 1
Apply the brakes to the castor wheels

Close-up of a mechanical component with mounting holes and a curved base, labeled 'Fig 1' (no other text or symbols visible)

1. Connect to electrical supply

Fig 2
2. Switch on power and set rocker switch to position 1

Fig 3
3. Select required fan speed (Variable speed versions only) 4. Switch off power and unplug unit when finished with.

CAUTION Ear defenders should be worn when fan is running at full speed. Max 85dba @ 1mt.