Casa 679/90 - Range hood Elba - Free user manual and instructions

Product Type	Range Hood
Brand	Elba
Model	Casa 679/90
Width	90 cm
Depth	50 cm
Height	60 cm
Weight	15 kg
Power Supply	220-240 V, 50 Hz
Max Power Consumption	200 W
Extraction Capacity	600 m³/h
Number of Speed Levels	3
Lighting Type	LED
Lighting Power	2 W
Filter Type	Aluminum grease filter
Duct Diameter	150 mm
Noise Level	55 dB (max speed)
Energy Class	A
Controls	Push buttons
Installation Type	Wall-mounted
Maintenance	Clean filters monthly; replace activated carbon filter if recirculation mode
Safety Features	Thermal cut-out; child lock (if available)
Spare Parts	Grease filter, LED bulb, carbon filter

Frequently Asked Questions - Casa 679/90 Elba

How do I install the Elba Casa 679/90 range hood?

Installation must be carried out by a qualified professional. Ensure the hood is mounted at the recommended height above the cooktop (typically 65-75 cm for electric hobs, 75-85 cm for gas). Connect the ducting to the outlet (if recirculation mode, install carbon filter). Refer to the user manual for detailed steps.

How often should I clean the grease filters?

Grease filters should be cleaned every 2-3 months, or more frequently with heavy use. They can be washed in the dishwasher or by hand with warm soapy water. Ensure they are completely dry before reinstalling.

Why is my range hood noisy?

Noise can be due to blocked filters, loose parts, or improper installation. Check that the filters are clean and properly fitted. If the noise persists, inspect the ducting for obstructions or contact a technician.

How do I replace the light bulb?

First, disconnect the hood from the power supply. Locate the lamp cover, unclip or unscrew it, and remove the old bulb. Replace with a new LED bulb of the same type and wattage (typically G4 or SMD). Reassemble and restore power.

Can I use the hood in recirculation mode without ducting?

Yes, if you do not have an external duct, you can use the hood in recirculation mode. In this case, you must install a carbon filter (optional accessory) to absorb odors. The filter should be replaced every 3-6 months.

What is the correct height to install the hood above the hob?

For optimal performance and safety, install the hood at a height of 65-75 cm above electric hobs and 75-85 cm above gas hobs. Always check local regulations and the user manual.

How do I select the right speed level?

Use low speed for simmering and light cooking, medium speed for normal frying, and high speed for heavy steam or odors. The Casa 679/90 has three speed levels; press the corresponding button to adjust.

My hood does not turn on. What should I check?

First, ensure the power cord is plugged in and the circuit breaker is on. Check if the thermal cut-out has tripped (wait for the motor to cool and reset). If the problem persists, inspect the control board or contact support.

What spare parts are available for the Casa 679/90?

Common spare parts include grease filters, LED bulbs, and carbon filters (for recirculation). You can order them from Elba dealers or online spare parts stores. Use the model number to ensure compatibility.

How to clean the exterior of the hood?

Wipe the exterior with a soft cloth dampened with mild detergent. Avoid abrasive cleaners or solvents that could damage the finish. Dry thoroughly. For stainless steel, follow the grain direction.

USER MANUAL Casa 679/90 Elba

Exterior view of a stainless steel Elsa air conditioner unit (no text or symbols visible on the appliance itself)

ELBA

ELBA

DESIGNER HOOD

Models: CASA 679/90

Owner's Manual

Please read this manual carefully before operating your set.

Retain it for future reference.

Record model number and serial number of the set.

See the label attached on the back cover and quote this information to your dealer when you require service.

For The Warranty Terms & Conditions, Please Refer To Warranty Certificate.

TROUBLESHOOTINGS

CAUTION: Disconnect the power supply before servicing.

STATUS	CAUSE AND METHOD OF REPAIRING	TOOL
The power supply is damaged	If the power supply is damaged, please call the technicians for repair.	"+" type Screwdriver Sharp Pincers
The lamp works but the motor does not run	a) Remove the motor fixed cover and rotate the fan by hand,If the fan cannot move smoothly, the core or bearings of the motor may be damaged. In this case, it must be replaced with a new motor.b) If the motor stops running and has a bad odor after a moment of operation, the motor wires may be burnout. In this case, it must be replaced with a new motor.c) If the condenser wire (yellow) is disengaged from the unit, it needs to be rewired.d) If the condenser is damaged, it must be replaced with a new condenser.	"+" type Screwdriver
The lamp works but the motor does not run	a) Take off the filter and check the connection between air inlet and wind chamber is sealed or not.b) Check the connection between air exhaust pipe and wind chamber leaks oil or not. If "YES", please fill it up with the varnish.	"+" type Screwdriver
Machine vibration	a) If the motors were not firmly screwed, screw tighten them up.b) If the fan is damaged or unbalanced, replace with a new one.	"+" type Screwdriver
Weak suction	a) The distance is too far between the Cooker Hood and the cooking appliance.b) There are many windows(doors) cause strong wind convection.c) Avoid installing the cooker hood where there are many doors or windows to affect the exhaust efficiency.	"+" type Screwdriver
Installation of the model is tilt	a) Adjust the height of the cooker hood on the wall.b) If the model tilt forward, lock into the wall with wood screw again (the screw peep out around 0.5 ~1 cm from the wall), or check the screws for fixing the model are loose or not.	"+" type Screwdriver
LED Lamp does not light	Just screw off the lamp shade and replace with a new LED, then put the lamp shade back.	"+" type Screwdriver

READ AND SAVE THESE INSTRUCTIONS MANUAL

CONTENTS

TECHNICAL CHARACTERISTICS....1

BODY SIZE 1

MAIN PARTS NAME 2

INSTALLATION REQUIREMENT....3

INSTALLATION PROCEDURES....4-6

OPERATING INSTRUCTION....6-7

MAINTENANCE....7

CLEAN THE BLOWER ASSEMBLY 7-8

TO REPLACE LIGHT BULB....8

IMPORTANT SAFETY INSTRUCTIONS....9-10

TROUBLESHOOTINGS....11

Please note that this product is marked with this symbol: According to Waste of Electrical and Electronic Equipment (WEEE) directive, WEEE should be separately collected and treated. If at any time in future you need to dispose of this product, Please do NOT dispose of this product with house hold waste. Please send this product to WEEE collecting points where available.

Dear consumer,

Thanks for your purchase of our cooker hood and we hope we can fully satisfy all of your needs. Please read entire instructions carefully before proceeding to obtain the best results of using the cooker hood.

TECHNICAL CHARACTERISTICS

MODEL NO.: Casa 679/90

TOTAL POWER: 254W

THREE SPEED MOTOR: 250W

LED LIGHTS: 2x2W

VOLTAGE: 220V\~240V

FREQUENCY: 50 Hz

FILTER: 6-layer filter

CONTROL: soft touch control

BODY SIZE

Dress the protective glove before you start to clean the hood. Remove the components gently during carrying out the cleaning.

Never wash the control switch with water or other kind of liquid as the liquid might cause electrical problem to the hood.

Cleaning the motor fan should be undertaken by a qualified person, pay full attention to avoid any distortion of the fan during carry out the cleaning.

Never pull the plug out of the power supply by wet hand to avoid the possibility of electric shock.

Disconnect the cooker hood from the power supply if this appliance will not be used for a long time.

IMPORTANT SAFETY INSTRUCTIONS:

MAIN PARTS NAME

Remarks: Screws are provided (4×expanding tubes, 4×wood screws, 4×M4 screws, 2×M4×10 screws)

INSTALLATION REQUIREMENT

1. Do not install the cooker hood where there are many doors or windows in order to avoid affecting the exhaust efficiency of the hood caused by air convection. (Fig. 1)

2. Install the cooker hood right above the hob. The recommended distance between the hob and the lower edge of the cooker hood is minimum 650mm and maximum 700mm. (Fig. 2)

3. In order to get the optimum performance, do not elongate the exhaust pipe too long, and try to make the bend of exhaust pipe less, to ensure the connection is airproof.(Fig. 3)

4. After hanging the unit on the wall, ensure the hood is level and vertical. (Fig. 4)

5. The air outlet must not be connected to chimney flues or combustion gas ducts.

1. Take out the motor fix cover like arrowhead's direction.

2. Use hexangular screwdriver to loose the fan fixed screws.

3. Take out the fan.

1. The same way to take out the other fan.

2. After cleaning, please assemble it like the opposite ways of loose it.

Note: Left motor fixed cover and fan have a little difference from right side, there is a letter "R" on the right side cover and a letter "L" on the left side cover. Don't assemble it in wrong side.

TO REPLACE LIGHT BULB

To replace LED lamp

Caution: LED lamp can not replace a new bulb, just can replace a new LED Lamp.

Make sure all the control switches are off, and the cooker

hood is unplugged! Please follow below instructions:

1. Take out the filters, and loose the wire connection of the lamp.

2. Press the spring according to the arrow direction, then you can take off the lamp unit.

3. You can replace a new LED lamp unit not more than the power rating of 2W.

4. Then put the lamp unit to the hood in reverse direction. Connect the wire of the lamp.

5. Fit on the filters.

B: Touch B, turn on the light. Press it again, turn off the light.

When the hood stay OFF, keep touching C 3 seconds, and then touch B and D to adjust hour and minute, at that time, G just like a clock. In the screen, left is hour, right is minute.

C: When the hood is working, touch C to control working time of hood.

1 minute per one touch, or you can touch C and don not loose your finger until the screen show the time you want. The longest time you can set is one hour.

D: Touch D, the fan runs at the high speed. Press it again, the fan turns off.

E: Touch E, the fan runs at the mid speed. Press it again, the fan turns off.

F: Touch F, the fan runs at the low speed. Press it again, the fan turns off.

MAINTENANCE

CAUTION: NEVER PUT YOUR HAND INTO THE COOKER HOOD WHILE THE FAN IS OPERATING.

FOR THE OPTIMAL LEVEL OF OPERATION, CLEAN THE RANGE HOOD SURFACE, FAN, AND ALUMINIUM FILTER REGULARLY.

1. Use only mild soap or detergent solutions to clean the cooker hood surface. Dry surfaces using soft cloth.
2. Using a stainless steel cleaner to bring the glow back into a stainless steel finish.
3. Clean the aluminium filter once a week or according to use status. Press the buckle of the aluminium filter slightly, take off the aluminium filter and put it into warm soapy water using mild detergent, wipe the aluminium filter with soft brush. Replace the filter after it is dry.
4. Clean the motor fan and other inside parts once every 6 months and use it according to this manual for better performance.
5. DO NOT clean the motor with water or other liquid.

CLEAN THE BLOWER ASSEMBLY

1. Take out the filters.
2. Loose the wire insert and power supply wire.
3. Loose earth wire.
4. Loose blower fixed screws.
5. Take out the blower assembly.
6. Take out the charcoal filter like arrowhead's direction (if you have installed charcoal filter).

INSTALLATION PROCEDURES

SAFETY WARNING

HOOD MAY HAS VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR SERVICING.

Step 1:

Please put the cooker hood on the wall and mark the position where you want to install. We recommend the height from the cooking appliance to the lower edge of the hood should be from 650mm to 700mm.

Step 2:

Drill 4 holes in level in the wall with 8mm in diameter and 75\~85mm in depth. Press the 4 expanding tube provided into the holes. Tighten the 2 wood screws of 5x60mm which supply together with the hood to the expanding tube, make sure it is fixed enough and does not move.

Step 3:

Hang the cooker hood to the 2 wood screws. Tighten the 2wood screws from the position of filters to the expanding tube. If the hood have little acclivitous, use the adjustable screws to adjust it to level.

Step 4:

Take out of the cooker hood from the carton and put it on a horizontal work table gently. Fix the reducer pipe into the air outlet of the inner duct, and then fix the exhaust pipe into the top of reducer, make sure is connected to the reducer tightly.

Step 5:

Matching the bracket to the holes of the inner duct cover and fix it well with M4 screws.

Step 6:

Insert the inner duct cover into the outer duct cover.

Please kindly note that the inner duct cover must fix to the outer duct cover's orientation slot.

Step 7:

Put the outer duct cover to the unit body, and use two M4x10 screws to fix the outer duct cover to the unit body.

Step 8:

1. Draw the inner duct cover up to the suitable high, mark on the wall two keyhole of the outer duct cover bracket with pen.
2. Put down the inner duct cover gently, drill the keyholes in 75-85 mm depth on the horizontal level using 8mm drill.
3. Press the expanding tube provided into the holes.
4. Matching the inner duct cover with the holes, tighten the inner duct cover with two 5x60mm wood screw provided

Step 9:

Extend the air outlet of the exhaust pipe out-of-door. Try to make the bend of the exhaust pipe less and ensure the connection is airproof.

Simple line drawing of a staircase with stairs and a chimney (no text or symbols)

Step 10:

Install grease filter. Match the fix pin to the fix hole and button the filter gently as the direction of arrow A.

A: Touch this button when the hood is working, it will preset a timer for 60 seconds. then be off. Touch this button twice, it will be OFF at once.