B-165 2436 - Sanitary accessory Bobrick - Free user manual and instructions

Product Type	Surface-Mounted Paper Towel Dispenser
Model	B-165 2436
Brand	Bobrick
Material	Stainless Steel (Type 304)
Finish	Satin
Dimensions (H x W x D)	24.75 x 10.0 x 7.75 inches (629 x 254 x 197 mm)
Weight	5.5 lbs (2.5 kg)
Capacity	Up to 200 C-fold or multifold towels
Mounting Type	Surface-mounted, pre-drilled holes
Fasteners Included	Yes (screws and anchors)
Loading	Top-loading with hinged lid
Warranty	Limited lifetime warranty
Compliance	ADA compliant (lever handle)
Compatible Towels	C-fold, multifold, or singlefold
Cleaning	Wipe with damp cloth; avoid abrasives
Maintenance	Check and lubricate hinge annually

Frequently Asked Questions - B-165 2436 Bobrick

How do I install the Bobrick B-165 2436 paper towel dispenser?

Mount the dispenser on a wall using the provided screws and anchors. Ensure the surface is clean and level. The keyhole slots allow for easy alignment. Refer to the installation template included for exact hole placement.

What type of towels does this dispenser accept?

The B-165 2436 accepts C-fold, multifold, and singlefold paper towels. Maximum capacity is approximately 200 towels.

How do I load towels into the dispenser?

Open the hinged top lid by lifting the recessed handle. Place a stack of towels into the opening, ensuring the folds are oriented correctly for smooth dispensing. Close the lid until it clicks.

Is the dispenser ADA compliant?

Yes, the lever handle is designed to be easily operated with one hand and meets ADA guidelines for accessibility.

How do I clean and maintain the dispenser?

Wipe the stainless steel surface with a damp cloth and mild detergent. Avoid abrasive cleaners that may scratch the finish. Lubricate the hinge mechanism annually with a silicone lubricant.

What is the warranty for this product?

Bobrick offers a limited lifetime warranty against defects in materials and workmanship. Exclusions apply for misuse or vandalism.

Can the dispenser be used in high-humidity areas?

Yes, the Type 304 stainless steel construction resists corrosion and is suitable for restrooms and other damp environments.

How do I adjust the dispensing mechanism if towels jam?

Ensure towels are not overloaded. Remove any jammed towels by opening the lid. If persistent, check that the dispenser is level and the towel stack is properly aligned.

What are the exact dimensions of the B-165 2436?

The dimensions are 24.75 inches high, 10.0 inches wide, and 7.75 inches deep (629 x 254 x 197 mm).

Can I use this dispenser with roll towels?

No, this model is designed exclusively for interfold (C-fold or multifold) paper towels, not roll towels.

USER MANUAL B-165 2436 Bobrick

MIRROR WITH STAINLESS STEEL CHANNEL FRAME

B-165

SERIES

Plain rectangular frame with no text, symbols, or markings

Designer's Notes:

1. Special-order sizes available on request.
2. Maximum size mirror available, 96" x 72" (244 x 183cm); minimum size, 12" x 12" (30 x 30cm).
3. All Bobrick framed mirrors are manufactured to overall width and height dimensions. EXAMPLE: A 24" x 36" (61 x 91cm) mirror will be furnished 24" x 36" (61 x 91cm) outside-of-frame to outside-of-frame.
4. To specify special sizes use Series Number followed by width x height in inches. EXAMPLE: B-165 2024 20" x 24" (51 x. 61cm)
5. Bobrick framed mirrors are manufactured to a tolerance 1/8" (3.2mm).
6. For sufficient space to lift mirror onto wall hanger(s), provide 1" (25mm) minimum clearance above top of mirror frame.
7. Provide 1/2" (12.7mm) minimum clearance on each side.

Snap Locking Design (Rear View)
Figure: 1 Figure: 2

STANDARD B-165 SERIES MIRRORS

MODEL NO.	OVERALL SIZE
	W	H
B-165 1824	18" (46cm)	24" (61cm)
B-165 1830	18" (46cm)	30" (76cm)
B-165 1836	18" (46cm)	36" (91cm)
B-165 2430	24" (61cm)	30" (76cm)
B-165 2436	24" (61cm)	36" (91cm)
B-165 2448	24" (61cm)	48" (122cm)
B-165 2460	24" (61cm)	60" (152cm)

"2S" Tab Design (Rear View)
- for all other mirrors up to a width of 36"

Note: Mirrors greater than 36" in width will have multiple hanger brackets with a typical 8" off each edge.

continued...

MATERIALS:

Frame — Type-430 stainless steel, 1/2" x 1/2" x 3/8" (13 x 13 x 9.5mm) channel with 1/4" (6mm) return at rear for Snap Locking Design; 1/2" x 1/2" x 1/2" (13 x 13 x 13mm) channel for Lock Tab Design, with bright polished finish. One piece frame with 90 degree mitered corners. Galvanized steel back has integral horizontal hanging brackets near the top for hanging the mirror and near the bottom to prevent the bottom of the mirror from pulling away from the wall.

Mirror — No. 1 quality, 1/4" (6mm) select float glass: selected for silvering, electrolytically copper-plated by the galvanic process, and guaranteed for 15 years against silver spoilage. Back is protected by full-size, shock-absorbing, water-resistant, nonabrasive, polyethylene padding.

Concealed Wall Hanger — For snap locking design: Heavy gauge steel construction. Incorporates upper and lower members, which engage backplate louvers to keep mirror against the wall. For "2S"-Tab design: Incorporates upper bracket engaging in upper louver and double sided tape below the bottom louver securing mirror to concealed wall hanger.

INSTALLATION:

Mount wall hanger on wall with screws (not furnished) at points indicated by an S. For plaster or dry wall construction, provide backing to comply with local building codes, then secure wall hanger with screws (not furnished). When providing a concealed backing, allow backing to cover minimum range of mounting hole locations shown on drawing. For other wall surfaces, provide fiber plugs or expansion shields for use with screws (not furnished), or provide 1/8" (3mm) toggle bolts or expansion bolts.

Snap Locking Design: Hang mirror on wall hanger with all four backplate louvers engaged behind horizontal wall hanger members. To do this, mirror must be centered in front of the wall hanger horizontally, pressed flat against the wall approximately 1" (25mm) above final position and then lowered into final position.

"2S" Tab Design: Comprises of two brackets, while the bottom one is furnished with double side tape. Bottom hanger bracket's mounting holes must be 1" - 1 1/2" above mirror's bottom edge. Note: Bottom hanger bracket is not supposed to engage with louvers of mirror's backplate. Hang mirror on wall top hanger bracket with the top two louvers engaged behind top wall hanger bracket. To do this, mirror must be centered in front of the wall hanger horizontally, pressed only at the top against the wall approx. 1" (25mm) above final position an then lowered into final position. When lowering, pull mirror's bottom edge off the wall by preventing bottom bracket from engaging. Once lowered, mirror must be pressed against wall to engage with double sided tape of lower wall hangar bracket.

Snap Locking Design — Locking devices automatically secure mirror to concealed wall hanger when it is lowered into final position (see figure 3). Locking devices may be unlocked by inserting two flat blade screwdrivers behind each side of mirror near the bottom or under the bottom of the mirror and pulling mirror bottom forward and then up.

"2S" Tab Design — Secure mirror to concealed wall hanger by pressing mirror against double sided tape of lower hanger once it is lowered into final position (see figure 4).

Snap Locking Design (Front View)

Figure: 4
"2S"-Tab Design - up to 36" Width (Front View)

SPECIFICATION:

Mirror shall have a one-piece type-430 stainless steel channel frame, with 90^irc mitered corners; all exposed surfaces shall have bright polished finish. Select float glass mirror shall be guaranteed for 15 years against silver spoilage. The back shall be protected by full-size, shock-absorbing, water-resistant, nonabrasive, polyethylene padding. Galvanized steel back shall have integral horizontal hanging brackets located at top and bottom for mounting on concealed wall hanger to prevent the mirror from pulling away from the wall. Locking devices secure mirror to concealed wall hanger. Mirror shall be removable from the wall.

Framed Mirror shall be Model B-165 ____ (insert width and height) of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.