Sinclair SNS041814LAJUDSN - Lighting AFX - Free user manual and instructions

Product Type	LED Indoor Luminaire, Wall Mount
Model Number	SNS041814LAJUDSN
Power Supply	120-277VAC, 60Hz
Dimming Compatibility	TRIAC (forward-phase), ELV (reverse-phase), 0-10V
Color Temperature	Adjustable via CCT switches; preset at 3500K
Location Rating	Indoor dry or damp locations
Installation Requirements	Requires handy box (2x4) – not included
Wiring Method	Hardwired via junction box
Grounding	Mandatory: green ground wire to mounting bracket
Warranty	5 years limited factory warranty
Safety Standards	FCC Part 15 Class B, ICES-005 (B) / NMB-005 (B)
Diffuser Material	Plastic (acrylic or polycarbonate) – removable for cleaning
Maintenance	Disconnect power before cleaning; use dry cloth
Repairability	No user-serviceable parts; contact qualified electrician
Spare Parts	Diffuser and mounting hardware available; contact AFX

Frequently Asked Questions - Sinclair SNS041814LAJUDSN AFX

What voltage does this fixture require?

This fixture requires 120-277VAC, 60Hz. Ensure your supply matches the fixture's voltage range.

Can this light be used in a bathroom?

Yes, it is rated for dry or damp locations, so it can be used in bathrooms or covered outdoor areas.

How do I adjust the color temperature?

Open the diffuser and locate the two CCT switches on each board. Set all switches to the same position to choose between 3000K, 3500K, or 4000K. The fixture is preset to 3500K.

Is a junction box required for installation?

Yes, you need a handy box (2x4) (not included) for mounting and wiring. All connections must be inside the junction box.

Can I use this fixture with a dimmer?

Yes, it supports TRIAC (forward-phase), ELV (reverse-phase), and 0-10V dimming. Follow the appropriate wiring instructions for your dimmer type.

How do I clean the fixture?

Always turn off power first. Wipe the diffuser and housing with a dry or slightly damp cloth. Do not use harsh chemicals.

What should I do if the light flickers?

Check that all wire connections are secure and capped. Ensure the dimmer (if used) is compatible. If problem persists, consult a qualified electrician.

Is grounding required?

Yes, proper grounding is mandatory for safety and proper operation. Connect the green ground wire to the mounting bracket's ground screw.

What is the warranty period?

AFX provides a 5-year limited factory warranty covering defects in materials and workmanship under normal use.

Can I install this fixture myself?

It is recommended to hire a qualified electrician to ensure compliance with local codes and safe installation.

USER MANUAL Sinclair SNS041814LAJUDSN AFX

LED Indoor Luminaires Wall Mount 120-277VAC / 60Hz

Model # SNS041007LAJUDSN SNS041814LAJUDSN

Safety Precautions

• Read all safety precautions and installation instructions carefully before installing or servicing this fixture. Failure to comply with these instructions could result in potentially fatal electric shock and/or property damage.
  • It is recommended that a qualified electrician perform all wiring. This fixture must be wired in accordance with all national and local electrical codes.
  • Do not handle any energized fixture or attempt to energize any fixture with wet hands or while standing on a wet or damp surface or in water.
• This fixture is designed for use in a 120-277VAC, 60Hz fused circuit. The fixture is compatible with Triac (forward-phase or leading edge) / ELV (reverse phase or trailing edge) and 0-10 V dimmers. Make sure that the power source conforms to the requirements of the fixture. (See labels on the fixture housing).
• To reduce the risk of electrical shock, and to assure proper operation, this fixture must be adequately grounded. To accomplish proper grounding, there must be a separate ground wire (green) contact between this fixture and the ground connection of your main power supply panel.
  • This fixture is intended to be used for general indoor lighting in dry or damp locations.
• Disclaimer

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian ICES-005 (B) / NMB-005 (B). These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiver antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult with the dealer or an experienced radio/TV technician for help.

Any modifications to this fixture may void the warranty and interfere with the safe operation of the luminaire.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Assembly Instructions

1. Preparing for installation.

A. Disconnect electrical power before installing or servicing any part of this fixture.
B. Remove fixture from carton; remove components from hardware kit.
C. This fixture requires handy box (2x4) – not included for installation.
D. Place the diffuser assembly (5) and hardware off to the side.
E. Install mounting bracket (1) to the handy box (not included) with two screws (2).

2. Wiring.

All wiring must take place inside junction box. Caution: Make sure power is off at fuse or circuit breaker box. Check power wires for damage or scrapes. If the power supply wires are within three inches of the driver, use a wire suitable for at least 90C (194F). Note: Most dwellings built before 1985 have supply wire rated to 60C. Consult a qualified electrician before installing.

A. This unit will not operate properly unless connected to a "grounded" electrical circuit. Electrical shock, overheating, low or no light output, and shortened LED life can result if proper grounding is not done. Securely attach power source ground wire and fixture ground wire to green ground screw on circular mounting bracket.
B. Make all wire connections to appropriate wire. Secure with wire nuts (provided).
C. For non-dimming fixture. Fixture will operate normal w/o connection to any dimmers. Connect white fixture lead to white (N) wire from supply power source. Connect black fixture lead to black (L) wire from supply power source. Gray and purple wires are not to be used and must be individually capped to prevent shorting.
D. For TRIAC dimming. Connect white fixture lead to (N) wire from dimming source per dimmer wiring instructions. Connect black fixture lead to black (L) wire from dimmer supply power source. Gray and purple wires are not to be used and must be individually capped to prevent shorting.
E. For (0-10V) dimming fixture. Connect gray wire from the fixture to the dimmer source gray wire. Connect purple wire from the fixture to the dimmer source purple wire. Connect white fixture lead to white (N) wire from supply power source. Connect black fixture lead to black (L) wire from dimmer supply power source.
F. Do not mix wires. Pull on each wire lead to make sure connections are secure. Make certain no bare wires are exposed outside of wire connectors. Tuck all connections neatly into junction box.

3. Fixture housing installation.

A. Install the fixture housing (3) by aligning two holes to mounting bracket (1) then secure with two nuts (4).

4. Color Changing Temperature Adjustment, CCT (if desired).

A. Adjust the two switches on each board accordingly to the desired color temperature as seen below. All boards must be set the same way. Note: Fixture is preset to 3500K from factory.

SNS041007LAJUDSN MODEL SHOWN

5. Diffuser installation.

A. Install the diffuser (5) by sliding over the front bracket and aligning top hole to the fixture housing then secure with screw (6). Note: Do not over tighten the screw as it may cause diffuser to crack or bow.

6. Power to the fixture can now be restored.

Limited Factory Warranty

AFX Inc. hereby warranty that this fixture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period of 5 years from date of shipment from factory. This warranty covers all component parts and extends only to replacement of defective fixture or components; it does not cover failure due to improper installation, misuse, mishandling or damage incurred in transit.

HANDY BOX

(NOT INCLUDED)