PowerLinc 2413S - Controller Insteon - Free user manual and instructions

Product Type	Power Line Modem & Controller
Brand	Insteon
Model	PowerLinc 2413S
Category	Controller
Communication	PowerLine (PLC) and RF (dual-band)
Interface	USB (USB-B jack)
Power Supply	AC wall outlet (120 V, 60 Hz)
Dimensions (approx.)	3.2 x 2.5 x 1.5 in (8.1 x 6.4 x 3.8 cm)
Weight (approx.)	4 oz (113 g)
Status Indication	LED and audible beeps
Set Button	Used for pairing, reset, and phase detection
Compatibility	Works with INSTEON devices and home automation software
Operating Temperature	32°F to 104°F (0°C to 40°C)
Humidity	Up to 85% non-condensing
Mounting	Plugs directly into wall outlet (desktop use)
Maximum USB Cable Length	10 ft (recommended 6 ft or less)
Phase Bridge Capability	Yes, with dual-band INSTEON devices
Reset Procedure	Unplug, hold Set button, plug in, release after beeps stop
Driver Support	VCP driver from FTDI Chip
FCC Compliance	Part 15, Class B
Maintenance	Clean with dry soft cloth; avoid liquids
Safety Precautions	Do not use with power strips or filters; avoid large metal objects
Spare Parts / Accessories	FilterLinc #1626-10 for computer power strip
Manufacturer Support	Insteon support line 800-762-7845, www.insteon.com/support

Frequently Asked Questions - PowerLinc 2413S Insteon

How do I set up the PowerLinc 2413S for the first time?

First, ensure the modem is not plugged into your computer. Download and install the VCP driver from fldichip.com. Then plug the modem into an AC wall outlet. Finally, connect the USB cable from the modem to your PC. The PC will detect new hardware.

Can I use a longer USB cable than the recommended length?

The maximum USB cable length is 10 feet, but 6 feet or less is strongly recommended for reliable communication.

Why should I avoid plugging the PowerLinc into a power strip?

Power strips and AC line filters can attenuate the PowerLine Carrier signals that the modem uses to communicate. Plug it directly into a wall outlet.

How do I reset the PowerLinc modem to factory settings?

Unplug the modem from the wall. Press and hold the Set button. While continuing to hold, plug it back in. A long beep will sound; keep holding until the beep stops, then release. The LED will light up to confirm reset.

How do I use the PowerLinc as a phase bridge?

First, install additional dual-band INSTEON devices. Tap the Set button four times quickly to start phase detection. The modem will beep and the LED turns solid green. Check the LED behavior on other dual-band devices: if they blink green or are bright white/blue, they are on the opposite phase. Tap the Set button again to finish.

What should I do if my computer equipment interferes with PowerLinc signals?

Use an INSTEON FilterLinc (#1626-10) on the computer's power strip. This prevents the computer from absorbing PowerLine Carrier signals.

Can I use more than one PowerLinc modem on the same computer?

No, only one PowerLinc modem should be used per computer.

What does the status LED indicate?

The Status LED shows the modem's state: solid on indicates normal operation; off means no power or fault; blinking may indicate activity or phase detection mode.

The modem is not detected by my home automation software. What should I check?

Ensure the VCP driver is installed correctly and no other program (like a scanner or PDA) is using the same COM port. Disable any such software. Also, try a different USB port or cable.

How do I clean the PowerLinc modem?

Use a soft, dry cloth to wipe the exterior. Do not use any liquids, cleaners, or abrasives.

USER MANUAL PowerLinc 2413S Insteon

1) Ensure PowerLinc Modem is not plugged into your computer
2) Go to http://ftdichip.com/Drivers/VCP.htm and download the driver file Under the "VCP Drivers" section, select the Windows .exe file
3) Open and run the downloaded driver file
4) Plug PowerLinc Modem into an AC wall outlet
5) Plug square end of included USB cable into PowerLinc Modem's USB jack
6) Plug rectangular end of cable into an available USB port on your PC PC will detect new hardware PowerLinc Modem is now ready

Tips for Using PowerLinc Modem

• Do not use a USB cable longer than 10' (6' or less is recommended)
• Do not plug PowerLinc Modem into a power strip or AC line filter
• Use only one PowerLinc Modem per computer
• Do not place near large metal objects, such as refrigerators or TVs
• Some computers and their accessories can absorb PowerLinc Carrier (PLC) signals off the powerlines. Since PowerLinc Modem will be close to the computer, the power strip for the computer should be filtered. Use an INSTEON FilterLinc (#1626-10) on the computer's power strip to keep PowerLinc Modem signals from getting absorbed by the computer equipment
• If computer's serial port is shared with another hardware device (scanner, PDA, etc.) be sure to turn off that device's program on the PC. If left running, the home automation software will not be able to communicate with PowerLinc Modem.
• To reset PowerLinc Modem to its original factory settings, unplug from wall outlet and wait 10 seconds. Press and hold Set button; while continuing to press and hold, plug back in. A long beep will sound; continue holding Set button until beep stops, then release.

After several seconds, status LED will turn on to indicate reset is complete

Use PowerLinc Modem as a Phase Bridge

1) Install additional dual-band INSTEON devices if they are not already installed
2) Start Phase Detection Mode by tapping the Set button on PowerLinc Modem four times quickly PowerLinc Modem will begin beeping and status LED will turn on solid green
3) Check the LED behavior of the other dual-band devices to see if they are on the opposite phase If at least one of the dual-band device LEDs is blinking green or is bright solid white or blue, the device is on the opposite phase. Continue on to step 4.
If none of the dual-band devices exhibit the behavior above, they are on the same electrical phase. Try the following:
• Follow steps 2 and 3 with the other dual-band devices to see if they are exhibiting the desired LED behavior
- Move a dual-band device to another location until it exhibits the desired LED behavior
4) Tap PowerLinc Modem Set button
PowerLinc Modem will stop beeping

Owner's Manual and Tech Support

Owner's Manual and current Quick Start Guide: http://www.insteon.com/support

Call: INSTEON Support Line at 800-762-7845

This device complies with FCC Rules Part 15. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause undesired operation. The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following measures: • Reorient or relocate the receiving antenna of the device experiencing the interference.

- Increase the distance between this device and the receiver

- Connect the device to an AC outlet on a circuit different from the one that supplies power to the receiver.

- Consult the dealer or an experienced radio/TV technician.

WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.