SLPORBT18 - Vacuum Cleaner SereneLife - Free user manual and instructions

Product Type	Automatic Robotic Pool Cleaner
Brand	SereneLife
Model	SLPORBT18
Dimensions	18.5 x 16.1 x 10.03 inches
Construction Material	ASA (Acrylonitrile Styrene Acrylate)
Input Voltage	115V AC, 60Hz
Output Voltage	24V DC
Output Current	4.5A
Power	150W
Suction Rate	4500 GPH
Filtration Accuracy	≥100 μm
Filter Type	Twin Cartridges
Filter Speed	14-18 m³/h
Floating Cable Length	55.8 ft
Cleaning Coverage	Floor and walls
Maximum Pool Length	Up to 50 ft
Cleaning Cycle Time	2, 3, or 5 hours (selectable)
Water Temperature Range	10-35°C (50-95°F)
Pool Depth Range	0.5 m - 3 m
Surface Area Capacity	Up to 100 m²
IP Rating (Controller Box)	IP54
IP Rating (Motor)	IP68
Key Features	Dual scrubbing brushes, wall climbing, tangle-free cable, energy saving
Box Contents	Cleaner, control box, user manual
Maintenance	Clean filter basket after each cycle; untwist cable as needed

Frequently Asked Questions - SLPORBT18 SereneLife

What does the SLPORBT18 robotic pool cleaner clean?

The SLPORBT18 cleans pool floors, walls, and waterline using dual scrubbing brushes and twin cartridge filters.

How do I set the cleaning time?

Press the RUNNING TIME button to cycle through 2, 3, or 5 hours. Red light = 2h, green = 3h, blue = 5h. The cleaner stops automatically after the set time.

Is it safe to use while swimming?

No. Do not operate the cleaner when people are in the pool. The cable can trip or entangle swimmers, posing a drowning risk.

What should I do if the cleaner stops moving?

Check for clogged filter basket, blocked impeller or drive belt. Clean the filter or remove obstacles. If the overload light blinks, let the cleaner sink to the floor and press ⏻ to restart.

Can I use the cleaner if the water temperature is outside 10-35°C?

No. Only operate in water temperature between 10-35°C (50-95°F) and pool depth 0.5m-3m.

How do I clean the filter basket?

Turn off and unplug the power supply. Open the filter cover, remove the basket, rinse with a hose, reinsert, and close the cover. Clean after each cycle for best performance.

What is the floating cable length and how to maintain it?

The floating cable is 55.8 ft. After long runs (e.g., 6-8 hours) it may tangle. Untwist manually before restarting to avoid issues.

What are the modes available?

Two modes: FLOOR CLEAN ONLY for pool floor only, and ALL PURPOSE CLEAN for floor, walls, and waterline. Select by pressing the mode button then ⏻.

What is the IP rating of the controller and motor?

The controller box has IP54 rating (dust and splash resistant). The motor has IP68 rating (submersion proof).

Where can I get replacement parts?

Contact SereneLife support at (1) 718-535-1800 or [e-mail]. Available parts include filter baskets, drive belts, wheel brushes, and more (see parts list in manual).

USER MANUAL SLPORBT18 SereneLife

Blue and white seranelife robotic device with visible sensor array and base plate (no text or symbols on body)

*☆☆☆☆☆☆☆☆

◆□○✿✿★□○□✿★□□✿✿

Pool Cleaning Robot with Two Motors, Wall Climbing,

Easy to Clean Up to 50 ft.

USER GUIDE

Please read this User Manual in its entirety to ensure proper operation and care of your SLPORBT18 Automatic Robotic Pool Cleaner.

IMPORTANT: PLEASE READ BEFORE OPERATING CLEANER

CONTENTS

1. Product Introduction 3
2. Warning and Cautions 3
3. Getting Started and Operation Instructions 4
4. Routine Maintenance 6
5. Troubleshooting 7
6. Specifications 8
7. Parts Breakdown and Replaceable Parts List 9

3D rendering of a blue and gray robotic cleaning robot with visible teeth and control panel (no text or symbols)

Product Introduction

We are sure that your SERENELIFE Automatic Robotic Pool Cleaner will provide you with reliable, convenient and cost effective pool cleaning. Its reliable filtration in all pool conditions, active brushing, and all-surface climbing brush enhance maximum pool hygiene.

The Automatic Robotic Pool Cleaner by SERENELIFE deliver advanced cleaning technology, long lasting performance and easy maintenance. You and your family will be free to enjoy swimming with full confidence that your pool is completely clean.

WARNING AND CAUTIONS

WARNING: Do not operate the robotic pool cleaner when there are people swimming in the pool. Communication cable can trip or entangle swimmers which could result in drowning.

WARNING: Keep the robotic pool cleaner out of reach of children. Keep the robotic pool cleaner out of reach of persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, without proper supervision and understanding of the instructions.

WARNING: DO NOT switch on the pool cleaner if it is not immersed in the water. Operating the cleaner out of the water may cause severe damage and will result in loss of warranty.

WARNING: • Shut off and unplug the power supply every time you remove the cleaner from the water.

WARNING: DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE, USE THE HANDLE.

WARNING: Only use this cleaner when the water temperature is 10-35°C or 50-95°F and the pool depth is 0.5m-3m. The cleaner is designed for 100m surface area.

WARNING: Keep the controller box in a dry place which is out of direct sunlight and is 3.5m away from your pool.

GETTING STARTED

1. ⏻: Turn power supply ON/OFF, error alarm.
2. FLOOR CLEAN ONLY: To clean the pool floor only. It will increase the cleaning efficiency
3. ALL PURPOSE CLEAN: All-around cleaning, including pool floor, pool wall and waterline.
4. RUNNING TIME (set the cleaning time): Set the preferred running hours (2/3/5 hours, press the button to set the cleaning time, red light means the cleaner will work for 2 hours, green light for 3 hours, blue for 5 hours), before you start the cleaning. The cleaner will stop automatically after working.

OPERATION INSTRUCTIONS

1. Place the power supply (transformer) at least 3.5 meters/11.5 feet from the pool and atleast 12 cm/4 inch above the surface. The transformer will supply low voltage to the cleaner.

1. Connect floating power cord.

Hand holding a tool interacting with a device, no visible text or symbols

1. Place the unit in the water. Release the Pool Cleaner and let it sink to the floor of the pool. Make sure that the floating cable is free of any obstructions.
2. Start: Turn the power supply ON (115V AC 60HZ). One of the three modes light will be on. Press the button for the mode and time you want to run, then press ⏻ button, the Pool Cleaner will now operate.
3. Mode switching: Press ⏻ button, choose the mode, press ⏻ button to start the cleaner.
4. Indicator Lights:

graph LR
    A["On/Off Button Floor Clean Only"] --> B["FLOOR CLEAN ONLY"]
    B --> C["ALL PURPOSE CLEAN"]
    C --> D["RUNNING TIME"]
    D --> E["Running Time"]
    style A fill:#f9f,stroke:#333
    style E fill:#bbf,stroke:#333
    subgraph "All Purpose Clean"
        F["serenelife"]
    end

Running Time Indication:

• Red light twinkling means the cleaner has been set for 2 hours
• Green light twinkling means the cleaner has been set for 3 hours
• Blue light twinkling means the cleaner has been set for 5 hours

DAILY MAINTENANCE

1. Clean the Filter Basket

Cut off the power supply (light goes out) Turn off the Pool cleaner.

Open the filter cover. Clean the filter basket with a hose. Insert the clean filter basket and close the filter cover.

Make sure the power supply is switched off and unplugged.

It is highly recommended to clean the filter basket after each cleaning cycle.

2. Floating cable daily maintenance

The floating cable may get intertwined after 6 hours of working which need to be sorted out manually. It highly recommend to sort the cable out after each cleaning.

TROUBLESHOOTING

Symptom Possible Reason Solution
The pool cleaner moves but does not clean the pool	Clogged filter basket Clean the filter basket
The pool cleaner does not move	• The impeller get blocked.• The drive belt get blocked	Check and clean the obstacle
Debris out from the outlet	• Filter basket is broken• Filter basket is full	• Replace the filter basket• Clean the filter basket
Intertwined floating cable	Long working hours, over 8 hours.	Untwist the floating cable before re-start.
Twinkling	Overload or no-load protection	Let the cleaner sink to the floor of the pool, and press ⏻ to start again.

SPECIFICATIONS

Features:

• Design to Clean the Pool Effortlessly
• With Dual Scrubbing Brushes and Superior Filtering Capabilities
• Saves Energy
• Traps and Locks-in All Sorts of Dirt and Debris
• Tangle-Free Cable
• Easy to Use
• Ideal for In-ground Swimming Pools Up to 50 Feet
  • Fully Automatic Robot Cleaner

What's in the Box:

• Cleaner
• Control box
• Manual

Technical Specs:

• Construction Materials: ASA
- Cleaning Area: Up to 50 Feet
- Cleaning Coverage: Floor and walls
- Cleaning Cycle Time: 2 hours, 3 hours, 5 hours (three modes)
• Filtration Accuracy: ≥100μm
• Length of Floating Cable: 55.8 ft.
• Filter Speed: 14-18 m3/h
- Filter Type: Twin Cartridges
• Output Voltage: 24V DC
• Output Current: 4.5A
- Input Voltage: 115V
• Frequency Response: 60Hz
- Horsepower: 150W
• IP Class for Controller Box: IP54
• IP Class for Motor: IP68
• Suction Rate: 4500 GPH
- Product Dimensions: 18.5" x 16.1" x 10.03"-inches

Parts Breakdown and Replaceable Parts List

NO. Parts Name Qty
1 Cover and wiring assembly 1
2 Filter Basket 2
3 Motor box 1
4 Wheel Brush 2
5 Buoyancy block 1
6 Driven wheel 4
7 Bearing 20
8 Side panel 2
9 Controller Box 1
10	Drive wheel	2
11	Drive belt	2

serenelife™

Questions? Issues?

We are here to help!

Phone: [phone]

Email: [e-mail]