BD1 - Bluetooth speaker Paradigm - Free user manual and instructions

Product Type	Universal Bluetooth Receiver
Brand	Paradigm
Model	BD1 (BD1E for international)
Bluetooth Version	v2.1
Supported Profiles	A2DP, AVRCP
Frequency Range	2.402 - 2.480 GHz
Operating Distance	Up to 10 m (30 ft) Class II
Syncing Distance	1 m (3 ft) Class I
Charging Input	DC 5V, 300mA
Standby Time	Up to 230 hours
Battery Life	Up to 12 hours
Battery Type	Built-in 250mAh Li-Polymer rechargeable
Dimensions (H x W x D)	45 mm x 33 mm x 8 mm
Weight	14 g
Power Source	AC adapter (included for NA) or USB AC converter (sold separately for international)
LED Indicators	Red/Blue blinking for pairing, solid red for charging, blue flash for standby/connected, red flash for low battery
Cable	3.5 mm stereo audio cable
Automatic Turn-Off	After 5 minutes if no device connected
Memory	Remembers last paired device
Warranty	1 year from date of purchase
Care Instructions	Avoid moisture, clean with soft cloth, do not use solvents

Frequently Asked Questions - BD1 Paradigm

How do I turn the BD1 on and off?

To turn ON, press and hold the power button for 3 to 5 seconds. To turn OFF, press and hold the power button for 3 to 5 seconds as well.

What do the blinking LEDs mean?

Red and blue alternating: Pairing mode. Blue flash once every 2 seconds: Standby, not connected. Blue flash twice every 5 seconds: Synced with device. Red flash every 20 seconds: Low battery, emits tones.

How do I pair the BD1 with my smartphone?

1. Turn off BD1. 2. Place phone about 1 meter away. 3. Press and hold power button for 6 seconds until LED alternates red/blue. 4. On phone, enable Bluetooth and select "SHIFT BD" from the list. 5. If prompted, enter PIN "0000". 6. Once connected, blue LED flashes twice every 5 seconds.

How do I pair the BD1 with a laptop or tablet?

Enable Bluetooth on your laptop/tablet following its manual. Then follow the same steps as for a smartphone: turn off BD1, press and hold power for 6 seconds, select "SHIFT BD" from the Bluetooth device list, and enter PIN "0000" if needed.

Why won't my BD1 connect to my device?

Ensure the device is within 1 meter (3 ft) during syncing. Verify your device supports A2DP or AVRCP Bluetooth profiles. Make sure Bluetooth is enabled and "SHIFT BD" is selected. If still failing, retry steps 1-7 from the manual or consult your device's manual.

How do I charge the BD1?

For North America: Plug the included AC adapter into an AC outlet and connect to the BD1's input jack. Red LED indicates charging; it goes out when fully charged (~2.5 hours). For international: Use a USB AC converter (sold separately) with the USB cable.

How long does the battery last?

The BD1 offers up to 12 hours of playback time on a full charge and up to 230 hours of standby time.

What should I do if the BD1 won't turn on?

Make sure the battery is charged or the unit is connected to the AC adapter with the adapter plugged into a powered outlet. If still not turning on, unplug from wall socket for a few seconds and reconnect to reset internal circuitry.

Can I use the BD1 while it is charging?

Yes, the BD1 can operate from AC power while plugged in and charging. You can leave it connected indefinitely.

How should I clean and maintain the BD1?

Clean only with a soft cloth. Do not use household cleaners or solvents. Avoid exposing to liquid, moisture, extreme temperatures, or dust. Do not dispose in fire; recycle according to local laws.

USER MANUAL BD1 Paradigm

The Paradigm SHIFT BD 1 is a universal Bluetooth receiver mobiles you stream music from any Bluetooth-enabled device supporting an Advanced Audio Distribution Profile (A2DP) or Audio/Video Remote Control Profile (AVRCP). This includes the iPhone, Android and Blackberry phones and other Bluetooth-enabled devices such as laptops and tablet PCs.

WHAT'S INCLUDED

• BD 1 Bluetooth Receiver
- AC adaptor and cable
• Built-in 250mAh Li-polymer rechargeable battery

Customers outside of North America

For our international customers the unit comes with a USB cable that plugs into a USB AC power converter (not included).

NOTE: The international version of this unit is designated BD 1E, however for information purposes in this manual it will be referred to as BD 1.

TURNING THE BD 1 ON AND OFF

Power ON: Press and hold the power button for 3 to 5 seconds

Power OFF: Press and hold power the power button for 3 to 5 seconds

WHAT ARE THE LEDs TELLING YOU?

BD 1's LED WHAT IS IT TELLING YOU?

LED flashes red and blue alternately. BD 1 is in pairing mode

Blue LED flashes once every 2 seconds. BD 1 is in standby mode and not connected

Blue LED flashes twice every 5 seconds. BD 1 is synched with the Bluetooth-enabled device

Red LED flashes once every 20 seconds. BD 1 is at low power and BD 1 emits audible tones

GETTING STARTED: (North American customers)

1. Plug the power supply into an AC outlet like the one on the back of the A2 speaker (see diagram). Plug the other end into the jack marked 'input' on the BD 1 receiver
2. The BD 1's red LED will come on, this tells you the unit is charging. A full charge takes approximately 2.5 hours. When the unit is charged, the red LED will go out.
3. The BD 1 can operate from the AC power and can remain plugged in. If desired, unplug and remove the AC power supply and operate the BD 1 off battery power.
4. Plug the BD 1's 3.5-mm cable into the 3.5-mm jack on your device (see diagram of the A2's stereo input below as an example).

GETTING STARTED: (Customers outside of North America only)

IMPORTANT: In order to connect your Bluetooth device to the BD 1E, you will need to purchase a USB AC power converter (sold separately) from your dealer.

1. Connect the supplied USB cable into a USB AC power converter (sold separately)
2. Plug the power supply into a power outlet. Plug the other end into the lack marked input on the BD IIE receiver.
3. The BD 1E's red LED will come on, this tells you the unit is charging. A full charge takes approximately 2.5 hours. When the unit is charged, the red LED will go out.
4. The BD 1E can operate from the AC power and can remain plugged in. If desired, unplug and remove the AC power supply and operate the BD 1E off battery power.
5. Plug the BD 1E's 3.5mm cable into the 3.5mm jack on your device see diagram of the A2's stereo input below as an example).

SYNCHING THE BD 1 WITH A BLUETOOTH-ENABLED SMART PHONE (All customers)

1. Turn off the BD 1
2. Place your Bluetooth-enabled mobile phone about 1 meter (approximately 3 feet) away from the BD 1 (once synching is complete maximum distance to maintain connection is approximately 10m/30ft)
3. Press and hold down the BD 1's power button for about 6 seconds until its LED alternates between Red and Blue
4. Activate your mobile phone's Bluetooth settings (located under 'Phone Settings' or 'Settings') and let the phone search for Bluetooth devices within range. Once it has found all devices select "SHIFT BD 1" from the list
5. If prompted for a password or PIN Number enter: "0000"
6. If prompted by your phone to connect, select: "Yes" or "Connect"
7. Once a connection has been established the BD 1's Blue LED will flash twice every five seconds.

NOTE: The LED will continue to flash until the BD 1 and the connected device are no longer connected or out of synch distance from each other

SYNCHING THE BD 1 WITH A BLUETOOTH-ENABLED LAPTOP PC OR TABLET (All customers)

If using the BD 1 with a laptop PC tablet, refer to your device's Operating Manual for how to enable Bluetooth, then follow steps 1 through 7 above.

INCOMING CALLS OR MAKING A CALL FROM YOUR PHONE

Music should pause automatically when you dial a phone number or receive an incoming call.

NOTE: This feature may not work on all Bluetooth-enabled phones. Check your device's Operating Manual.

GENERAL OPERATION

• If no devices are sensed, the BD 1 will automatically turn off within five minutes
• After successful synching, the BD 1 and smart phone will remember each other and you will not have to resynch again. If for some reason you do have to resynch, simply follow Steps 1 through 7 above.
• Each time the BD 1 is turned on it will automatically try to connect to the last device to which it was connected. If you want to synch it with a new Bluetooth device, go to 'Settings' or 'Phone Settings' on your phone and turn off the Bluetooth function of the last connected device and synch with the new device following Steps 1 through 7 above.
• If the BD 1 is turned on but will not synch to the new device, press the power button twice and synching should occur. If not, refer to the "Troubleshooting" section
• When the receiver and the Bluetooth-enabled device are out of range of each other they will be automatically disconnected. They will automatically reconnect once they are again within range.

CARE AND MAINTENANCE

In order for you to get the best from your BD 1, read the following recommendations:

• Do not expose the receiver to liquid, moisture or humidity as this will damage the product's internal circuit and such damage is not covered under warranty
• Clean only with soft cloth. Do not use household cleaners or solvents of any kind.
• Do not expose the receiver to extremely high or low temperature as this will shorten the battery life.
• Do not dispose of the BD 1 in an incinerator or fire as this will result in a dangerous explosion. Recycle the product according to the recycling directions at the beginning of this manual and according to your local laws and bylaws
• If the BD 1 will not be used for an extended period of time place it in a clean, dry place free from high temperatures, humidity, moisture and dust

RECHARGING THE BD 1's INTERNAL BATTERY

See "GETTING STARTED" section.

TROUBLESHOOTING

The BD 1 won't turn on

- Make sure the battery is charged or that the unit is connected to the AC adapter and plugged into an un-switched, powered AC outlet. If the unit will not turn on with the AC adapter connected and powered, unplug the unit from wall socket for a few seconds then reconnect the AC power to reset the unit's internal circuitry.

The BD 1 won't turn off

- Make sure the battery is charged or the unit is connected to the AC adapter and plugged into an unswitched, powered AC outlet. If the unit will not turn on with the AC adapter connected and powered, unplug the unit from wall socket for a few seconds, then reconnect the AC power to reset the unit's internal circuitry.

The BD 1 won't connect to the device

- Make sure the Bluetooth-enabled device is no more than 1 meter (3 feet) away from the BD 1 when performing the synching operation.

• Recheck to ensure the device is:
  a) Bluetooth-enabled and
  b) Supports Advanced Audio Distribution Profile (A2DP) or Audio/Video Remote Control Profile (AVRCP)
• Make sure your phone's Bluetooth settings are enabled and that "SHIFT BD 1" is selected
• Repeat steps 1 through 7 listed at the top of this page.

NOTE: If synching still fails after all of the above troubleshooting attempts have been tried please refer to the Owners Manual for your Bluetooth-enabled device for additional information and/or solutions.

TECHNICAL SPECIFICATIONS

Bluetooth Version Bluetooth v2.1

Bluetooth Profiles Supported A2DP and AVRCP

Frequency Range 2.402 GHz - 2.480 GHz

Operating Distance 10 meters (approximately 30 feet), Class II

Synching Distance 1 meter (approximately 3 feet), Class II

Charging Input Voltage/Current DC 5V 300mA

Standby Time 230 hours

Battery Life Up to 12 hours

Dimensions 45 mm × 33 mm × 8 mm

Weight 14 g

WARRANTY

Paradigm warrants this product against defects in materials and workmanship under normal use and operation for a period of one (1) year from the date of purchase by the original end-user/purchaser. Maintain your original sales receipt for proof of purchase. For complete warranty information visit our website at www.paradigm.com/shift.