HC90RGB - Lawn mower Conair - Free user manual and instructions

Product Type	Hair Clipper / Trimmer
Brand	Conair
Model	HC90RGB
Power Supply	Corded Electric
Blade Material	Stainless Steel
Blade Type	Precision ground blades
Adjustable Taper Lever	Yes (for fine-tuning cut length)
Guide Combs Included	Yes (multiple sizes for varying lengths)
Usage	Home hair cutting (flat tops, crew cuts, etc.)
Maintenance	Oil blades regularly (special oil included)
Cleaning	Remove blade assembly, brush clean
Safety	Keep away from water; unplug when not in use
Warranty	Limited 2-year warranty
User Manual Included	Yes (PDF available)

Frequently Asked Questions - HC90RGB Conair

How do I clean the Conair HC90RGB clipper?

To clean, unplug the clipper, remove the blade assembly, and brush away hair clippings. Wipe the blades with a dry cloth. Do not immerse in water.

How often should I oil the blades?

Oil the blades before each use. Apply a few drops of the special oil provided to the blade teeth and let it run for a few seconds.

What guide combs are included?

Multiple guide combs are included for different cut lengths, typically ranging from 1/8 inch to 1 inch or more. Refer to the manual for exact sizes.

Can I use the clipper on wet hair?

No, the Conair HC90RGB is for dry hair only. Using on wet hair may damage the blades and pose a safety risk.

How do I adjust the cutting length?

Use the adjustable taper lever on the side of the clipper to fine-tune the cut length without changing combs. Combine with guide combs for precise results.

What is the warranty period?

The Conair HC90RGB comes with a limited 2-year warranty. Retain your proof of purchase for any claims.

Is the clipper cordless?

No, the HC90RGB is a corded electric clipper for consistent power.

How do I replace the blade?

If the blade becomes dull, you can order replacement blades from Conair. To remove, unscrew the blade assembly and disconnect it from the clipper. Install the new blade and adjust the alignment as described in the manual.

Why is my clipper making a loud noise?

A loud noise may indicate the blades are not properly oiled or aligned. Clean and oil the blades first. If the noise persists, check the blade alignment and adjust if necessary.

Can I take this clipper on a plane?

Yes, as a corded personal care item, it is generally allowed in carry-on luggage. However, check with your airline for specific regulations.

USER MANUAL HC90RGB Conair

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING

BEFORE USING KEEP AWAY FROM WATER

DANGER—Any appliance is elec-

trically live, even when the switch is off. To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water. Unplan immediately

2. Do not use while bathing or in the shower.

3. Do not place or store appliance where it

Can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.

1. Always unplug this appliance from the electrical outlet immediately after using

2. Unplug this appliance before cleaning.

DO NOT REACH INTO THE WATER

INTU THE WATER WARNING

WARNING—To reduce the risk of burns, electric shock, fire, or injury to

persons: 1. An appliance should never be left

unattended when plugged in. 2. This appliance should not be used by

1. This appliance should not be used by, on, or near children or individuals with certain disabilities.

2. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.

3. Never operate this appliance if it has a damaged cord or plug, if it is not working

property, if it has been dropped, damaged, or dropped into water. Return the appliance to service center for

Examination and repair. 5. Keep the card away from heated surfaces

1. Never operate the appliance with the air

opening blocked or while on a soft surface, such as a bed or couch, where the air goatings may be blocked. Keep the air

openings may be blocked. Keep the an openings free of lint, hair and the like. 7. Never drop or insert any object into any

1. Never drop or insert any object into any opening.

2. Be not sure extent to open?

3. Do not use outdoors or operate where aerosol (spray) products are being used or where organized is being administered.

4. Always attach plug to appliance first, than to outlet. To disaspart, pure all con-

them to outlet. To disconnect, turn all controls to "off", then remove plug from outlet.

1. Do not place appliance on any surface while it is operating.

2. Do not use this appliance with a dam

3. Do not use this appliance with a damaged or broken comb or with teeth missing from the blades, as injury may occur.

4. Avoid skin contact with moving blades.

5. When using the appliance with its cord, be mindful of tangles or kinks in the cord. If the cord does his own tangible use

cord. If the cord does become tangled during use, turn the unit off and straighten cord before starting a part.

before operating again.

SAVE THESE NSTRUCTIONS

OPERATING

OPERATING NSTRUCTIONS

INSTRUCTIONS This appliance has a polarized plug (one

blade is wider than the other). As a safety feature, the plug will fit into a polarized outlet

only one way. If the plug does not fit fully into the outlet, try reversing the plug. If it still

does not fit, contact a qualified electrician. Do not attempt to defeat the safety feature.

Your new Conair Haircut Kit has everything you need to achieve professional haircuts at

home. Its powerful magnetic motor clipper with High Carbon steel blades for long lasting

cutting precision. Also included are four attachment combs for different hair lengths.

It also comes with a barber comb, barber scissors, cleaning brush, lubricating oil and a

blade guard for easy maintenance of the clipper blades.

[Non-Text]

[Non-Text]

[Non-Text]

THE CONAIR GUIDE TO CUTTING HAIR AT HOME Before you start:

1. Inspect your clipper to make sure it is free of hair and dirt, is properly priced and is run-

of half and one, is properly once and is running smoothly.

1. Place a tower of cape around the neck on the person getting the haircut.

2. Seat the person so that his/her head is at your eye level. This gives you greater visibili-

3. Comb hair until it is tangle-free. Hold the

clipper in a comfortable grip. Now you're ready to cut.

MEDIUM TO LONG CUT

To begin, cut only a small amount of hair until you become used to the length each

with you desire to be longer when attachment leaves the hair. Try the longest attachment so the clinner first. If you want a

- Short attachment comb (number 1) cuts

- 60ft ultralimem comb (number 1) calls hair to 1/8".

• Medium-Short attachment comb (number 2) cuts hair to 1/4".

- Medium-Long attachment comb (number 5) cuts hair to 3/8^ .

- Long attachment comb (number 4) cuts hair to 1/2" .

NOTE: Never push or shove the clipper

through the hair to make it move more quickly. Professional experience

shows that the clipper works most efficiently when it cuts through the

affording which is also through the hair at its own speed.

To begin cutting hair:

1. The half should be combed in its natural direction.

2. Using the largest attachment camb 1km

Sachment cone, thin sides from the bottom upward. Hold clippur

upward: little onppert lightly against the hair with forth of the attach-

ment comb pointing up—wet flot against the head. Gradually lift the

even shorter:

A) Apply more pressure to the head with the attachment.

with the remarkable comb that is in place. This takes a little

peace. With takes a little practice at first.

OR Bi Just switch to

a shorter attachment comb.

STOP, COMB, CHECK. For best results, do as the professionals do: comb the hair often and check results as you comb. This way you can avoid uneven sides, bangs, neckline, etc. OUTLINING: Outlining resulges no attachments. Comb the

Hair into the desired style. Position the clipper between the sideburns and the ear (see

per between the brooding and the surface sketch) and make sure the corner edge of the blade is against the hairline. With the outline

of the hair as your guide, slowly move the clipper over, around and behind the ears. For

C

(2)

m - 1 0 ;

m : x = 1 或 3x + 4y + 1 = 0

the back of the neck and the sideburns, hold

the clipper upside down (see sketch) and, holding it against the skin at the length

desired, move the clipper downward.

SHORTCUTS TO PERFECT FLAT TOPS, CREW CUTS, ETC. Always cut the hair from the back of the

comb setting. Hold the comb attachment flat against the head and closely move the edge.

against the head and slowly move the clipper up through the hair. Use the same technique for the side, cutting from the bottom to the

for the sides, cutting from the bottom to the upper side of the head.

For the front of the crown, cut the hair against its natural direction. Then even it up

with the sides. For a flat top use a flat comb, not the attach-

ment comb. Just cut top hair by running the clinker over the comb.

To taper hair down to the neckline, use the upper setting attachment and. Crush the hair

lower settings attachment tools. Comb the hat and check for uneven spots. Outline the side-burns and neckline areas (see Outlining).

USER-MAINTENANCE INSTRUCTIONS

CARE OF YOUR CLIPPER

replacement, or if they should be knocked out of alignment. How can you tell if the blades need peligating? Simply match them

tubles need roasting? Simply match with up, point for point, to conform with the drawing below.

(1)

1. To prevent the clinker from contacting the

It is to prevent the drop from containing the skin or cutting too closely, make certain that the end of the top blade is 1/32" In 1/16"

back from the bottom blade. 2. Position the extreme left-hand tooth of the

top blade so that it either covers, or appears on the left of the first small tooth on the bot-

tom blade. 3. Make sure that the big tooth on the bottom

blade touches the extreme right-hand tooth on the top blade.

SPECIAL OIL

To maintain the blades of your Conair® clipper in peak condition, oil them after every three or four haircuts. Gently place a few drops of oil on the teeth of the blades, using the special Conair oil included with your set. Turn the clipper on for a minute, then turn off. This light, natural oil was formulated specifically for the Conair® high-speed clipper. Because it is the right oil to use, it will not slow down the blades. Never use any other product; there is no substitute for Conair oil. Keep oil out of reach of children

[Non-Text]

POWER SCREW

The power screw permits you to adjust power to your clipper. You may need to make this adjustment if the power in your house is low. (The Conair® clipper was designed for household use.)

1. With a screwdriver or a dime, turn the power screw clockwise until the arm strikes the coil, making a clacking noise. (FIG. 1)

FIG. 1

1. Then turn the screw counterclockwise, just until the noise stops. This is the maximum power setting. (FIG. 2)

Never pull on the clipper cord. Never twist or wrap the cord around the clipper. To store your clipper, lay it flat with the cord coiled up, then place in cylinder.

If clipper stops cutting, check to see if there is a clump of hair lodged between the blades. If that is the problem, unplug the clipper and then loosen the blades to remove the hair.

If the clipper stops cutting but does not stop running, you will need to check the blades. For new blades, send a check or money order for \5.00 plus \2.50 for postage and handling to:

STORAGE:

STORAGE. When not in use, your clipper should be disconnected and stored in a safe, dry location, out of reach of children.

Conair Corporation Service Department

150 Milford Road East Windsor, NJ 08520

。

YOU RE WRONG.

HAPP, AVISTA BROSSE MATER

KEEP AWAY FROM WATER

Everyone knows that electricity and water are a dangerous combination. But did you know that an electrical appliance is still electrically alive even if the switch is off? If the plug is in the power is on. So when you are not using your appliances, keep them unplugged.

ALWAYS UNPLUG

SMALL APPLIANCES Public Service ad from Association of Home Appliance Manufacturers and Underwriters Laboratories, Inc.

LIMITED TWO YEAR WARRANTY

Corajir will repair or replace (at our option) your unit free of charge for 24 months from the date of purchase if the appliance is defective in workmanship or materials.

To obtain service under this warranty, return the defective product to the service center listed below that is nearest you, together with your purchase receipt and \$3.00 for postage and handling. California residents need only provide proof of purchase and should call 1-800-366-0937 for shipping instructions. In the absence of a purchase receipt, the warranty period shall be 24 months from the date of manufacture.

ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE 24 MONTH DURATION OF THIS WRITTEN, LIMITED WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental, or consequential damages, so the above limitation may not apply to you. This regulatory gives us a special legal opinion, and

I find warranty given you specific legal rights, and you may also have other rights, which vary from state to state.

©2004 Conair Corporation

Service Centers:

Conair Corporation Service Department

150 Milfort Road

East Windsor, NJ 08S20

The Ground Truth image displays a single, solid horizontal line. According to Rule 2 (UNDERSCORE & LINE RULES), this is a stylistic or background line, not a placeholder underscore. Therefore, the OCR result must ignore it and output nothing or only meaningful text. The provided OCR content is "____", which consists of four underscores. This is an incorrect interpretation of the line as a placeholder, violating the rule that stylistic lines must be ignored. The OCR has hallucinated underscores where none should exist based on the GT's visual context. Hence, the OCR result is inconsistent with the Ground Truth.

04MF371

Once again, thanks for buying a

Conseir product.

Your Conair ^® clipper blades are made of high carbon, stainless steel. They are

cutoff - stainless - beret. They are engineered for precise, professional results.

If Glades feel like they are pulling or grabbing

hair, it means they are losing their sharpness and should be replaced as room as possible.

Eno adobre de replasod da soon as possible.

Attachment combs should also be replaced if they are lost or broken. It is easier to cut hair

they are look of brown. It is usual to cut hard with the accuracy of a gre when the

necessary tools are at your fingertips.

Conair makes a variety of accessories

for different haircut kits. If your haircut kit

does not include them, you may want to consider adding them to your professional

consider using them to your professional haircutting tools.

Left and right gar attachment combr

Lett and right car attachment controls provide effortless, precise cutting around the

ears. Styling clips hold hair in place when you

are sectioning hair. A styling comb makes it easy to taper or cut hair at an angle. A barber

cape ensures a comfortable and neat haircut

and a convenient storage pouch keeps all your

essentials in one place.

Last but not least, an easy-to-follow 30-

minute "Haircuts at Home" video is available. It demonstrates basic haircutting

available. It demonstrates basic handcutting techniques and follows four popular

haircuts step by step. It will give you the

confidence and instruction you need to give great looking because to every member of

great looking narcotics to every member of your family.

m = 311

F

-

1

1

[Unreadable]

1. 2017年

中

-

Subsequently

Rechargeable heart and mut

trimmer with 1

feature, stainle:

blades and 5 p attachment co

for a blended a

tapered trim.

Bloss blot L otho

Nell Ho; Latne • WO

8th

sha

•

•

1

1

-

广力云

HAIRCUT KIT REPLACEMENT PARTS & ACCESSORIES ORDER FORM Prices in effect through June 7, 2004. Orders posted ahead after this date

STRAWBAN RESEARCH CURRENT
S&P 500 Index Options
S&P 500 Earnings Comp. S&P '120, '130' Fts at 60 points	COMB-10	5.00
S&P 500 Financials Comp. S&P 500 ex spot and right on Fts at 60 points	COMB-11	1.75
T-Coml-Fits all-clippers	COMB-12	1.75
Earnings Alternative Com. S&P '120, '130' Fts at 60 points	COMB-13	5.00
Top-Share	HCBK-1	1.50
Disclose White Wire with Viscus Color	CARP-1	5.00
Lubricating Oil (Lig. of 3 bush)	HC OIL	2.00
Approximate Oil/Benelian tobacco in Spanish & English (Cotimes)	NC OBDO	4.00
Instructional CVD	DVO-1	5.00
Barber Sanders	SC-1	2.00
Black Sea Oil & WOCS	BCL-12	8.00
Blended Sea Oil & WOCS-1.00
Sliding Caps (see it of)	CLP-1-1.0
Additional benefits from management to the company's credit, including:25/32 USvs.1.5M; net worth: 25M; net worth:2M; net worth: 1M; net worth:1M; net worth: 1M; net worth:1M; net worth: 1M; net worth:1M; net worth: 1M; net worth:1M; net worth: 1M; net worth:1M; net worth: 1M; net worth:1M; net worth: 1M; net worth:1M; net worth: $1M.
VISA
ACCESS
CPY	AFT
	STRALY
TELEPHONE (a) (the bid for sale or a royalty based on this):
For information on the Chief Financial report by LLC - USD-A/CAMR

•

Conjunto de

Cortair Corporation 150 Milford Rd.

East Windsor, NJ 08520

[Non-Text]

ADVERTENSION: 01

ADVERTENCIA: SI

CREE QUE NO HAY

2022 Q3 1985

CORRIENTE,

SE EQUIVOCA

SE EQUIVICA

East Windsor, NJ 08520

[Non-Text]

SANTHUA BEEF AED

MANTENGA ESTE APARATO

ALEJADO DEL AGUA

10

| 20

|

(1)

32

[NO TEXT]