PT7840S - Hob Cylinda - Free user manual and instructions

Brand	Cylinda
Model	PT7840S
Product Type	Freestanding or built-in washing machine
Height	850 mm
Width	595 mm
Depth	700 mm
Weight	92 kg (net)
Drum Volume	80 L
Maximum Load	8 kg (depending on program)
Spin Speed	Up to 1400 rpm (max)
Water Pressure	0.1 - 1 MPa (1-10 bar)
Drum Material	Stainless steel
Number of Programs	21 (including special programs)
Energy Efficiency Class	Not specified in manual
Noise Level	< 70 dB (sound pressure)
Child Lock	Yes
Delayed Start	Up to 100 hours
Overflow Protection	Yes
Self-Cleaning Program	Yes (Drum Clean)
Water Connections	Cold water only (hot water optional)
Power Supply	230 V~, see rating plate for details

Frequently Asked Questions - PT7840S Cylinda

What is the maximum load capacity of the Cylinda PT7840S?

The maximum load capacity is 8 kg, but it may vary depending on the selected program. Refer to the program chart for specific limits.

How do I activate the child lock?

Go to Settings and select Child Lock. Set it to On. When activated, no other functions can be selected until it is disabled.

What should I do if the washing machine displays an error code?

Switch off the appliance, wait 1 minute, and restart. If the error reappears, note the code (e.g., E3 for water filling) and refer to the error table in the manual or call service.

Can I use liquid detergent?

Yes, use the foldable barrier in the detergent compartment. Add liquid detergent to the front part of the main wash compartment. Follow the manufacturer's dosage recommendations.

How do I clean the detergent compartment?

Press the tab to remove the tray. Rinse it thoroughly, clean the cap and tube, and use a brush for the nozzles. Do not wash in a dishwasher. Wipe the door rubber seal after each wash.

What is the purpose of the self-cleaning program?

The Drum Clean program removes detergent residue and bacteria. Run it monthly with a small amount of powder detergent, without laundry.

How do I adjust the feet for stability?

Use a No. 32 spanner to rotate the adjustable feet. Level the machine longitudinally and transversely. Tighten counter-nuts with a No. 17 wrench to secure.

What does the 'Add clothes' function do?

It allows you to pause the program and add or remove laundry after the start. The function is available during the wash phase for most programs. Press Start/Pause to pause.

Why is the washing time longer than displayed?

Factors like low inlet temperature, uneven laundry distribution (UKS system), low mains voltage, or power failures can extend the time. The display updates during the cycle.

How do I manually open the door in case of power failure?

Ensure the machine is off and unplugged. Use the emergency door opening tool located at the back of the detergent compartment. Insert it into the slot on the right side of the door latch and press down until you hear a click.

USER MANUAL PT7840S Cylinda

Simple line drawing of a kitchen appliance with oven, refrigerator, and washing machine (no text or symbols)

PT7840S

Innehåll

Introduktion .... 3

Snabbguide 4

Line drawing of a front-loading washing machine with open door and side panel (no text or symbols)

Line drawing of a single washing machine on a base (no text or symbols)

Inbyggdtvättmaskin

Justerafötterna

Line drawing of a washing machine with internal tubing and mounting bracket (no text or symbols)

Line drawing of a front-loading washing machine with visible door, wheels, and side panel (no text or labels)

Line drawing of a front-loading washing machine with a worker installing components on the side (no text or symbols)

INFORMATION!

Tvättsymboler

Front view of a computer monitor with control buttons and a play button (no text or symbols)

Slåpå

Line drawing of a hand opening a washing machine (no text or symbols)

②.

Line drawing of a single washing machine with an open door (no text or symbols)

③.

Line drawing of a washing machine with clothes being cleaned from the door (no text or symbols)

Front view of a remote control interface with a circular button and directional arrows (no text or symbols)

Front view of a computer monitor with control buttons and a play button (no text or symbols)

Line drawing of a front-loading washing machine (no text or symbols)

ELSTÖT!

1

Diagram showing a device with a sensor and a numbered component (no text or symbols present)

2

Line drawing of a mechanical device with internal compartments and a directional arrow (no text or symbols)

Line drawing of a front-loading washing machine with circular vent and side lock (no text or symbols)

Two circular diagrams showing mechanical components with arrows indicating direction, no text or symbols present.

INFORMATION!

** UI = (User Interface)

Line drawing of a front-loading washing machine with two doors open, showing internal compartments (no text or symbols)

Kontaktadress

Cylinda Service

0771-25 25 00

Du betalar endast lokal telefontaxa

www.cylinda.se

Tekniskinformation

Energimärkning

Washing machine description 58

Dispenser tray 59

Before using for the first time 60

Installation and connection 62

Tips before washing 68

Washing process step by step (1-8) 71

Settings 78

Cleaning and maintenance 81

Errors – what to do? 84

Service 92

Before calling a service technician 92

Technical information 93

Energy labelling 93

Technical information 93

Program chart 94

PT7840S 94

Adjustment of the displayed washing time 95

Removal 97

Disposal / recycling of packaging 97

Introduction

Dear Cylinda customer!

Welcome to the family of Cylinda customers.

We hope that you will have many years of use from your new machine.

The machine has many features. To make the most of its functions, we recommend that you read the operating instructions before using the machine. The operating instructions include information on how you can help protect the environment.

The following symbols are used throughout the manual and they have the following meanings:

INFORMATION!

Information, advice, tip, or recommendation

WARNING!

Warning –general danger

ELECTRICSHOCK!

Warning – danger of electric shock

HOTSURFACE!

Warning – danger of hot surface

DANGEROFFIRE!

Warning –danger of fire

Original instructions

See Quick guide on the last page.

Quickguide

Sortthelaundry. Close the zippers. Empty the pockets and turn them inside out. Check the laundry care symbols. Sort the laundry based on how heavily soiled it is, by colour, and by material.

SwitchonthemainON/OFFswitch

2

Openthewashingmachinedoorandinsertthelaundry. Before doing so, make sure the drum is empty.

Addthedetergentandtheconditioner. 4. Recommended detergent amount is usually indicated on the packaging. For smaller wash loads, use a smaller amount of detergent.

Choosethewashingprogram. Turn the program selector knob to the desired washing program. Selected program will be indicated on the display unit. Maximum load is indicated on the rating plate (see PROGRAM TABLE in the instruction manual).

6 Choose the program settings Program settings can be set for some programs. See chapter: SETTINGS

Closethewashingmachinedoorandpressthe"START"button. Anticipated washing time, in hours and minutes, will be indicated on the display.

Endofprogram Open the door and remove the laundry from the washing machine. See chapter "CLEANING AND MAINTENANCE". 8. Close the door. Switch off the main on/off switch. Close the water tap and remove the power plug from the power socket (unless you have a washing machine with a 3phase connection).

Safetyprecautions General

Pleasereadtheinstructionmanualandsaveitforfuture reference.

• Pleasedonotusethewashingmachineifyouhavenot readandunderstoodtheseinstructionsorusefirst.
• Failure to observe the instructions for use or inappropriate use of the washing machine may result in damage to the laundry or the appliance, or injury to the user. Keep the instruction manual handy, near the washing machine.
• Instructions for use are available on our website at www.cylinda.se.
• The appliance has to be connected to the water and power supply by a trained expert.
• Any repair and maintenance pertaining to safety or performance should be done by trained experts.
• To avoid hazard, damaged power cord may only be replaced by the manufacturer, authorized service technician, or other authorized person.
  • After installation, the washing machine should stand still for two hours before it is connected to the power mains.

• The washing machine may not be connected to the power mains using an extension cord.

• Do not connect the washing machine to an electrical outlet intended for an electric shaver or hair dryer.

• To connect the washing machine to water supply, make sure to use the supplied water supply hose and gaskets. Water pressure has to be between 0.1 and 1 MPa (approximately 1–10 kp/cm ^2 , 1-10 bar, 10–100 N/cm ^2 ).
• Always use a new water supply hose to connect the appliance to water supply; do not reuse an old water supply hose.
• Afterthewashingcycle,closethewatertapandpullout thewashingmachineplugfromthepowersocket.

If you have a washing machinewith a 3-phase connection, do not pull the plug out of the power outlet.

• Only use the washing machine for washing laundry, as described in the instruction manual. The machine is not intended for dry cleaning.
• In case of incorrect appliance connection, incorrect use, or servicing by an unauthorized person, the user shall bear the cost of any damage.
• Only use detergents intended for the washing machine!
• Only use agents for machine washing and care of laundry. We shall not be responsible for any damages or discolouration of gaskets and plastic parts resulting from incorrect use of bleaching or colouring agents.

- Bleaches that contain chlorine can be replaced with oxygen-based bleaches. Otherwise, a neutralization cycle should be performed by running the Cotton program at the highest temperature. For best results, use hydrogen peroxide or oxygen-based detergents.

- Do not use colourants (dyes) or bleaching substances (substances for discolouration or removal of colourants) as they contain sulphuric compounds that could cause corrosion.

- Excessive use of products containing chlorine compounds increases the risk of premature failure of appliance components. This depends on the concentration of chlorine, exposure time, and temperature.

• DANGEROFFIRE!

Do not use detergents that contain solvents as this could lead to release of poisonous gases, damage to the machine, and risk of fire and explosion.

- Before using the appliance for the first time, remove the transport bolts and all other transport protection devices. See chapter "BEFORE FIRST USE/Transport protection".

- The machine is not intended for use by persons (including children) with physical or mental impairments, or persons with lacking experience and knowledge. These persons should be instructed about the use of the appliance by a person responsible for their safety.

- Emergency door opening tool is located on the back side of the dispenser.

• Maximum washing capacity in kg is indicated on the rating plate (or in the PROGRAM TABLE).

This appliance is intended to be used in household and similar applications, such as:

• staff kitchen areas in shops, offices and other working environments;
• farm houses;
• by clients in hotels, motels and other residential type environments;
  • bed and breakfast type environments;
• areas for communal use in blocks of flats or in launderettes.

For appliances without plug, disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

Childsafety

• Do not allow small children to play with the washing machine.
• Before closing the washing machine door and running the program, make sure there is nothing except laundry in the drum (e.g. if a child climbed into the washing machine drum and closed the door from the inside).
• Keep the detergent and conditioner out of reach of children.
• Activatethechildlock.See chapter: SETTINGS

- Donotletchildrenyoungerthanthreeyearscomenear theappliance, unless they are under constant supervision.

- The washing machine is made in compliance with all relevant safety standards. This washing machine may be used by children aged 8 years and above and by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, but only if they are supervised during the use of the appliance, if they have been provided relevant instructions regarding safe use of the washing machine, and if they understand the hazards of inappropriate use. Make sure children do not play with the appliance. Make sure the children do not clean the washing machine or perform any maintenance tasks without supervision.

Dangerofhotsurface

- At higher washing temperatures, the door glass will heat up. Be careful to avoid burns. Make sure children do not play near the door glass.

Overflowguardfunction

If the water level in the appliance rises above the normal level, then the excessive water level protection will be activated.

It will shut off the water supply and start pumping out the water.

If the water level does not decrease in 60 seconds, the program will be interrupted (see chapter "ERRORS – WHAT TO DO?").

Transporting/storageduringthewinter

If you transport or store the appliance in vehicles or rooms that are not heated and where the temperature could drop to below freezing point, please do the following:

• Close the water supply to the washing machine, undo the water supply hose from the water supply tap, and wait until the water flows out of the tap and the hose.
• If the washing machine is to be transported, transport protection has to be re-installed before transport (see chapter "BEFORE USING THE APPLIANCE FOR THE FIRST TIME").

SAVETHESEINSTRUCTIONSFORFUTUREREFERENCE!

Washingmachinedescription

1. Main switch (ON/OFF)
2. Program selector knob
3. Display
4. Program selector buttons
5. Button (start/pause)
6. Dispenser tray
7. QR and AUID code (on the inside of the washing machine door)
8. Rating plate with information about the washing machine (on the inside of the washing machine door)
9. Washing machine door

Dispensertray

Prewash compartment1

2 Compartment for main wash liquid detergent. Use the foldable barrier (3).

2 Compartment for main wash powder detergent. Do not use the foldable barrier (3).

4 Softener / conditioner compartment

5 Tab for detergent compartment removal

Beforeusingforthefirsttime

Packaging

Remove all packaging.

Please sort the materials in compliance with local recommendations (see chapter "DISPOSAL").

Transportprotection

Before using the appliance, remove the three transport bolts and plastic plugs which protect the appliance during transport.

1

Release and remove the bolts as shown in the figures.

2

To remove the plastic plugs holding the bolts, squeeze them and then pull them out.

3

Remove the caps from the plastic plugs. Push the caps over the three holes in which the plastic plugs were inserted. Save the bolts and plastic plugs if you have to transport your washing machine in the future.

INFORMATION!

If you wish to transport the washing machine, reinstall the bolts and plastic caps to lock the machine. This will prevent any damage to the machine due to vibrations during transport. If you have lost the transport bolts or plastic caps, replacements can be ordered at your dealer.

Please order three pieces of each item!

	ID:Art.No.
	Bolt270698
	Plastic cap (transport lock)551188

Cleaning

Disconnect the washing machine from the power mains and open the door. Clean the washing machine drum with a damp cloth and a mild detergent.

In the case of a 3 phase connection of the appliance, switch off the main socket switch.

Line drawing of a front-loading washing machine with open door and side panel (no text or symbols)

Connect the washing machine to the power mains and run the dedicated drum cleaning program. See chapter "WASHING PROCESS; STEP BY STEP (1–8)" /STEP 5: CHOOSE THE PROGRAM.

INFORMATION!

No program can be started while the door is open.

Settingsbeforefirstuse

When the dryer is connected (see chapter "INSTALLATION AND CONECTION") and switched on for the first time, choose the preferred language:

For further washing process, see chapter "WASHING PROCESS STEP BY STEP".

INFORMATION!

The amount of detergent also depends on the hardness of water. For details, see the detergent packaging. Please contact your local water supply company to check the water hardness in your area.

INFORMATION!

Before the product is dispatched from the factory, every appliance is tested.

Installationandconnection

Positioningthewashingmachine

The washing machine can be installed as a built-in (integrated) or a free-standing unit. Place the machine on a level surface so that the power outlet on the wall is accessible.

INFORMATION!

Before connecting the washing machine to the power mains, wait for at least 2 hours until it reaches room temperature.

INFORMATION!

If the appliance is installed on a plinth or a similar structure, then the appliance must be fixed to it, to avoid the risk of falling. Original accessories are available for this purpose, complete with fixing instructions.

Line drawing of a single washing machine on a base (no text or symbols)

Built-inwashingmachine

The washing machine can be integrated under a worktop with a height of 900–950 mm. Leave 5 cm of room around the entire appliance, including between the back edge of the upper cover and the wall behind it.

Washingmachineinstallationclearances

To stack an CYLINDA dryer on top of a washing machine, use the extra vacuum feet and the tipping guard (A+B), supplied in the cardboard box in the CYLINDA dryer drum.

Adjustingthefeet

Place the washing machine so that it is stable.

1. Level the washing machine in longitudinal and traverse direction by rotating the adjustable feet (using a No. 32 spanner). The feet allow levelling by +/- 1 cm.

2. When the appropriate height of feet is set, use the wrench No. 17 to firmly fasten the counter-nuts towards the bottom of the appliance.

3. Tighten the jam nuts (counter nuts) to the end position. This will reduce washing machine noise, vibration, movement etc. to minimum.

Movingthewashingmachineandtransportafterinstallation

If you are moving the washing machine without packaging, open the washing machine door and pull the appliance by holding the washing assembly, as indicated in the figure.

For any further moving of the appliance, use the transport rods (the washing machine drum has to be blocked).

(See chapter TRANSPORT PROTECTION.)

Connectiontowatersupply

INFORMATION!

The machine has to be connected to water supply by an adequately trained person.

Use the water supply hose to connect the appliance. Water pressure has to be between 0.1 and 1 MPa (approximately 1–10 kp/cm ^2 , 1-10 bar, 10–100 N/cm ^2 ).

If the hoses are newly installed, we recommend rinsing them to remove any impurities. Otherwise, these impurities could clog the filter in the water connection on the washing machine and thus cut off the water supply.

The water intake hose has to be fastened firmly enough for the hose to have a good seal.

After connecting the hose, the seal must be checked for any leaks.

Only use the water supply hose supplied with the appliance. Do not use any used or other hoses.

INFORMATION!

If the connection on the supply hose is of different dimensions than the water tap (e.g. 3/4" → 1/2"), use an adapter.

Connectingtohot/coldwatersupply

(Only available in some models)

If your appliance has connections for both hot and cold water, then connect one hose to the cold water connection and the other hose to the hot water connection, as indicated on the back of the appliance:

$$ \text { COLD } = \text { cold and HOT } = \text { hot. } $$

Hot water is supplied for programs operating at 40 °C or more.

INFORMATION!

Connecting to both hot and cold water will save time and electric energy when washing.

If your washing machine model has connections for both hot and cold water, and you only wish to connect cold water, then the protective cap has to be (or remain) attached to the hot water connection.

Installingthedrainhose

Line drawing of a washing machine with a hand operating the door (no text or symbols)

Water supply hose is supplied with the appliance.

This is attached to the machine's outlet and routed to a floor drain or drainage pipe.

Line drawing of a front-loading washing machine with a diagonal line indicating cleaning or repair (no text or symbols)

INFORMATION!

The height of the mouth of the outlet hose must be lower than the lowest part of the outlet valve.

Connectingtothepowermains

ELECTRICSHOCK!

After installation, the washing machine should stand still for two hours before it is connected to the power mains.

Connect the appliance to an earthed power outlet. After installation, the wall outlet should be freely accessible. The outlet should be fitted with an earth contact (in compliance with the relevant regulations).

If you have a washing machine with a 3-phase connection, the connection must be carried out by a qualified and authorized specialist.

Connection upon delivery

TYPE: WMXX.XXXXXX MODEL: XXXXXX.X

Art.No.:XXXXXX/XX Ser.No.:XXXXXXXX

IPX4 XX Hz 卷 XX-X MPa

Information about your washing machine is indicated on the rating (type) plate.

Use the type A differential current protection switch.

ELECTRICSHOCK!

We recommend using over-voltage protection to protect the appliance in case of a lightning strike.

WARNING!

The washing machine may not be connected to the power mains using an extension cord.

INFORMATION!

Do not connect the washing machine to an electrical outlet intended for an electric shaver or hair dryer.

INFORMATION!

Any repair and maintenance pertaining to safety or performance should be done by trained experts.

Tipsbeforewashing

This chapter includes several tips on how to prepare the laundry for washing.

Laundrysorting

Sort the laundry according to:

•how soiled it is,
•colour,
- material.

Clothing

1. Close the zips and hook-and-loop fasteners so that they do not damage the fabric.
2. New dyed items may contain excess dye; therefore, they have to be washed separately several times.
3. Turn delicate items inside out. This will decrease the risk of tear and colour fading.
4. Place very sensitive clothes and small items in a special-purpose laundry washing bag.
5. Empty the pockets and turn them inside out.

Laundrysymbols

Observe the laundry symbols.

Textile maintenance symbols:

Washing
		DelicateNormal
	Max. washing temperature 90 °C
	Max. washing temperature 60 °C
	Max. washing temperature 40 °C
	Max. washing temperature 30 °C
	Hand wash only
	Do not wash
Bleaching
	Bleaching in cool water
	Bleaching not allowed
Drycleaning
	Dry cleaning with all agents

Tablecontinuedfromlastpage

P	Perchloroethylene R11, R113, petroleum
F	Dry cleaning in kerosene, pure alcohol, and R113
⊗	Dry cleaning not allowed
Ironing
	Ironing with a hot iron with a maximum temperature of 200 °C
	Ironing with a hot iron with a maximum temperature of 150°C
	Ironing with a warm iron with a maximum temperature of 110°C
⊗	Ironing not allowed
Naturaldrying
	Drying on a flat surface
	Drying without prior spinning
	Drying on a clothes line or a hanger
Tumbledrying
	Drying at high temperatures
	Drying at low temperatures
	Tumble drying not allowed

Dyedcotton

Laundry made of dyed cotton which is to be washed at 60 °C should be first washed at a temperature of 60 °C to remove the excess dye. If this is not done, there is danger of dye being washed out of such items. To maintain the colour of the fabric, use bleach-free detergent.

Unbleachedlinen

Unbleached lining fabric should be washed at 60 °C with a detergent free of bleach or optical bleaching agents. Heavily soiled linen laundry may be occasionally washed at higher temperatures, but do not do this too often as heat could ruin the sheen and strength of linen clothing.

Wool

These fabrics are intended for either machine or hand wash. The Wool Wash program is equally gentle or even gentler than an actual hand wash.

Wool in particular is sensitive to washing and similar procedures.

Viscoseandsyntheticfibres

Materials made of viscose and some synthetic fibres are highly sensitive, and require a lot of space in order not to crease.

INFORMATION!

Viscose and acetates are fragile when wet.

Reducingallergicreactions

The options include washing with the Allergy Program Cotton and Allergy Program Synthetics. These programs can be used for people with sensitive skin, such as those suffering from allergies, or small children.

Savingtimeandenergy

Save time and energy by using the Quick program

Economyandefficiency

You can save a lot of energy by not using the programs operating at higher temperatures.

Choose the Quick program. This will save water and power.

Detergents

Detergents carrying the environment protection label are less harmful to the environment.

Onlyaddthedetergentsincompliancewiththerecommendationsbydetergentmanufacturers.

Recommended amount of washing detergent at certain loads and water hardness levels are specified on the detergent packaging.

Stains

If your clothes are soiled with stubborn stains (blood, eggs, coffee, grass etc.), they should be appropriately treated before the wash. Then, wash your laundry using the special programs (if your washing machine has them).

Do not use any chemical substances or agents; only use the stain removing detergents.

When using bleaches or stain removal agents, there is danger of trust (corrosion) and discolouration.

WARNING!

To protect the environment, we advise against using powerful chemicals.

Washingprocessstepbystep(1-8)

STEP1:Sortthelaundry

See chapter "TIPS BEFORE WASHING".

INFORMATION!

Use a washing net for underwire bras. Empty the pockets. Coins, nails etc. could damage the machine and the fabric.

STEP2: Turnonthemainswitch.

Front view of a computer control panel with buttons and a play button (no text or symbols)

Turningon

Press the on/off button.

Switchingoff

Press the on/off button.

If the machine does not accept the on/off command correctly, wait for at least 8 seconds before pressing any other button.

STEP3: Openthewashingmachinedoorandinsertthelaundry

Open the washing machine door by pulling the handle towards you.

①

Line drawing of a hand opening a washing machine (no text or symbols)

②.

Line drawing of a front-loading washing machine with a door open (no text or symbols)

③.

Illustration of a washing machine with clothes being cleaned from it (no text or symbols)

Place the laundry into the washing machine drum.

Before doing so, make sure the drum is empty.

Do not overload the drum!

If the washing machine drum is too full, the laundry will not be washed as thoroughly.

STEP4:Addthedetergentandtheconditioner.

Recommended amount of detergent is usually specified on the detergent packaging. When washing a smaller amount of laundry, the amount of detergent used can be decreased.

Observe manufacturers' recommendations regarding the type of detergent suitable for certain temperatures, load size, and water hardness.

Powderdetergent

Add powder detergent into the main wash detergent compartment. If you have selected the Prewash function, Heavy, MOP or Disinfection program, then add powder detergent to the prewash detergent compartment.

INFORMATION!

We recommend adding the powder detergent immediately before the washing cycle. Otherwise, make sure the detergent compartment is completely dry before adding the powder detergent, as otherwise, the powder detergent may cake before the start of the washing process.

Liquiddetergent

When using a liquid detergent, observe the detergent manufacturer's recommendations. When using thick detergents, we recommend always using the laundry balls. Use the barrier (3) in the detergent compartment; see figure in the chapter "Detergent compartment". Add the liquid detergent in the front part of the detergent compartment (2).

Laundryballorwashingbag

If you are using a laundry ball or a washing bag, place it directly into the drum and choose a program without any prewash.

INFORMATION!

An excessive amount of detergent will not improve washing results. Rather, it will lead to foaming and increase the environmental impact. We recommend using less detergent. Only increase the dosage if you are not satisfied with the washing results.

Conditioner

Pour the conditioner into the detergent compartment, into the compartment with the symbol ⚙. Observe the recommendation on the conditioner packaging.

INFORMATION!

Do not fill the conditioner compartment over the max. indication (maximum indicated level). Otherwise, the conditioner will be added to the washing machine drum too soon, leading to poorer washing effect.

STEP5: Choosetheprogram.

The display shows the program name, water temperature and spin speed. The washing machine has pre-selected programs when delivered from the factory. You can replace pre-selected programs. Contact the service department about which programs are available and how to change the pre-selected programs or. See section: SETTINGS.

Choose the program by rotating the program selector knob in either direction. Confirm the program selection by pressing the button under the program.

Front view of a remote control interface with a circular button and directional arrows (no text or symbols)

Choose the program depending on the type of laundry and how heavily soiled it is (see chapter "TIPS BEFORE WASHING").

Estimated program duration will appear on the display.

Choose between the following programs:

(owner/distributor can change parameters and rename the program)

	program)	DescriptionPrograme(factorydefault
	HEAVY 60°C	For heavily soiled laundry with dirt that needs to be fully dissolved before the main wash. A prewash is used to do this.
	HEAVY 90°C	For heavily soiled laundry with dirt that needs to be fully dissolved before the main wash. A prewash is used to do this.
	WHITE/COLOR 20°C	Program for normally to heavily soiled laundry, whites and colours.
	WHITE/COLOR 40°C	Program for normally to heavily soiled laundry, whites and colours.
	WHITE/COLOR 60°C	Program for normally to heavily soiled laundry, whites and colours.
	WHITE 90°C	Programme for normally to heavily soiled laundry. 90 °C is a good temperature for white and light-coloured cotton, such as bed linen.
	SUPER QUICK 40°C	Use this program for laundry that just need freshening up. The lower the selected temperature, the shorter the program time.
	SUPER QUICK 60°C	Use this program for laundry that just need freshening up. The lower the selected temperature, the shorter the program time.
	SYNTHETIC 40 °C	Program for synthetics, delicate blended fabrics and permanent press cotton. Suitable for shirts and blouses.
	WOOL/HAND 30°C	A gentle laundry program for wool, silk and garments that should be washed by hand. This wash program has a short spin.
	RINSE	One cold rinse and a short spin cycle. Suitable for laundry that just needs to be rinsed.
	SPIN	Use this program when you only want to spin the load.
	DRAIN	Use this program when you only want to drain the water from the machine.

Tablecontinuedfromlastpage

	program)	DescriptionPrograme(factorydefault
	MOP 60°C	A program specially developed for cleaning mops.
	MOP 90°C	A program specially developed for cleaning mops.
	MICROFIBRE 40°C	A program specially developed for cleaning microfibre fabrics.
	MICROFIBRE 60°C	A program specially developed for cleaning microfibre fabrics.
	DISINFECTION 40°C *	Programme where the temperature reached during the main wash is maintained above 40 °C for 20 minutes. Disinfection at this temperature requires special detergent.
	DISINFECTION 60°C *	Programme where the temperature reached during the main wash is maintained above 60 °C for 60 minutes. Disinfection at this temperature requires special detergent.
	DISINFECTION 90°C *	Programme where the temperature reached during the main wash is maintained above 90 °C for 10 minutes. Disinfection at this temperature requires special detergent.
	ALLERGY COTTON 60°C	This program is used to wash normal to heavily soiled clothes that require special care, such as clothes for people with highly sensitive skin or skin allergies.
	ALLERGY COTTON 90°C	This program is used to wash normal to heavily soiled clothes that require special care, such as clothes for people with highly sensitive skin or skin allergies.
	ALLERGY SYNTHETIC 40°C	This program is used to wash clothes that require special care, such as clothes for people with highly sensitive skin or skin allergies.
	ALLERGY SYNTHETIC 60°C	This program is used to wash clothes that require special care, such as clothes for people with highly sensitive skin or skin allergies.
	CLEANING	This program is used to clean the drum and to remove detergent residue and bacteria. The drum must be empty.
	PROGRAMS A - J	Program slot that can be programmed for your needs.See chapter: SETTINGS.

* Programs Disinfection (40 °C, 60 °C, 90 °C) cannot be canceled during washing program. Complete cycle will be done.

STEP6: Choosing the program settings

Using the program settings, the washing programs can be further adjusted to your wishes. See chapter: SETTINGS.

(only appliance owner/distributor may change the settings)

Someprogramsettingsmaynotbeavailableforyourselectedprogram.

Start delay

Choose the delayed start when you wish the washing program to start after a certain period of time (from 1 h to 100 h after you press the Start button).

Use the Program selector knob to set the delay (from 1 hour to 100 hours in 1-hour steps).

Press the button to confirm your selection.

Start delay time + time remaining until the end of the washing program will be displayed. When the countdown is over, the selected washing program will start.

To cancel the start delay, press the button Cancel.

Then press the Start button to start the program.

When Start delay time is once set, it is not possible to change it; the only possibility is to »Skip it« and continue with chosen program.

INFORMATION!

If you have set the delayed start function and you are using liquid detergent, we do not recommend choosing a programme with a pre-wash cycle.

STEP7:Startthewash

Close the washing machine door and press the Start ▶/Pause button.

Front view of a computer monitor interface with control buttons and a play button (no text or symbols)

▶ Start (pressed briefly – start/resume)

II Pause (short press of the button - pause)

Stop (press and hold for 3 seconds – stop or cancel)

Remaining time

Depending on the selected program, anticipated washing time will be displayed in hours and minutes.

Actual washing time will depend on the selected program, load, type of laundry, spin speed etc.

Actual washing time may be longer or shorter than initially displayed.

Remaining time will be updated during the program duration, depending on the actual amount of laundry and amount of water pumped into the machine. The last remaining time update takes place before the final spinning cycle.

In case of uneven distribution of laundry, the time on the display will flash and it will not count down. Once the laundry is evenly redistributed, the washing time will continue and it will stop flashing.

Adding or removing laundry after the start of the program

To add laundry during washing program, you must first select the enable/disable option. (See chapter: SETTINGS).

To add or remove laundry during the progress of a washing program, use the Start/Pause button to pause the program.

The door may be opened when the water is pumped from the machine (but not completely pumped out). Then, add or remove the laundry. Close the door and continue the program. Press the Start ▶ /Pause button.

The program will resume from the point at which it was interrupted.

If the door cannot be opened, it is possible that the temperature in the machine is too high, and you won't be able to add the laundry.

Also, if the door cannot be opened, it is possible that the program has been running for too long and any laundry added at that point would not be efficiently washed.

Pausing, stopping or changing the program

To pause the program, shortly press the Start/Pause II button.

To resume a program, press the Start ▶ /Pause button again.

To stop the washing program, press the Start/Pause button and hold it for 3 seconds.

Choose "Stop program". The program is canceled and the water is pumped out of the machine if necessary. Only then will you be able to open the washing machine door. Use the Program selector knob to select a new program. If necessary, add detergent, and then press the Start ▶/Pause button.

INFORMATION!

If the temperature in the drum is very high, then cooling procedure starts before program is canceled.

A washing program can be paused by pressing the ON/OFF button.

The washing machine will switch off.

After the washing machine is switched on, press the Start button to resume the program.

INFORMATION!

Do not open the detergent compartment while the appliance is operating.

INFORMATION!

In some cases the door may be locked although no program is in progress (e.g. in case of an error). To unlock the door, press the Start/Pause button and hold it for a while.

STEP8:Endofprogram

After the end of the washing program, the display will indicate that the program has been successfully completed and that the door is unlocked.

Open the door towards you and remove the laundry from the washing machine.

Make sure the washing machine drum is empty.

If you do not take any action within 5 minutes after the end of the program, the display will switch off to standby mode in order to save power.

The display will light up again if you press the ON/OFF button.

WARNING!

After the washing cycle, close the water tap and pull out the washing machine plug from the power socket.

If you have a washing machine with a 3phase connection, do not pull the plug out of the power outlet.

Settings

Onlyapplianceowner/distributormaychangethesettings!

(owner/distributor should check Service manual)

		DescriptionSettingOndisplay
Max. RPM	no Drain --> max. rpm	Setting affect all programs
	Valve/DrainDrain	Setting of draining via valve or pump, depending on the type of appliance; in case of change, a mechanical change on the appli-ance is required.
	On/OffShowtemp	In the Disinfection programs and in the Special programs; this means displaying the actual measured temperature in the drum.
Changeprogram	On each program (some set-tings cannot be set on some programs)	By changing settings it is pos-sible to create and customize your own program. Program can be renamed!
•Prewash	On/Off
•Change temperature		°C/°F0 --> max
•Change spin RPM	no Drain --> max. rpm
•Water Level	On/Off
•Anti-crease	On/Off
•Save program	Override existing/Save as new	Once the above changes are done, you can save the program as a new program or overwrite an existing program.
	0 --> 300Spintime	At max. rpm in the Spinning phase
Temperature unit	°C/°F	Choose either °C or °F.
	On/OffSuperrinse	Additional rinses to the program are added.
	On/OffPaymentsystem	With enabled function payment is requested, to be able to start the program.
	On/Off3Dsensor

Tablecontinuedfromlastpage

		DescriptionSettingOndisplay
	On/OffChildLock	Choose between switching the Child lock On or Off. When the child lock is activated, no other function can be selected.
Programmes		Selected program will be shown on display
SetLanguage	Select your language - press the button under the flag	•Select language: by rotating the program selector knob•Confirm language: by pressing button under the country flag
Temporary language selectionIf a temporary language is selec-	On/Off	(from 0 to 5)ted, then the user can temporarily select a language for the time the machine is turned on.
	0 --> 5Soundsetting	5 different sound levels can be set. 0 means, sound is turned off.
Displaysettings:
•Brightness	1 --> 5	5 different brightness levels can be set.
•Display the logo	On/Off	After turning the appliance on, the introduction text can be turned off, so that is not shown.
		1h --> 100hOn/OffStartdelayChoose the delayed start when you wish the program to start after a certain time (from 1h to 100h, after you press the Start button).
	On/OffHeatingsteps	Program will be done without heating step, water will not be heated.
	On/OffDetailedview	Sub menu for the program can be disabled. User can not go to sub menu. Program can be started directly from the first level of the menu.
	On/OffAddclothes	User can pause the program and select option "Add clothes", door will be unlocked and user can add laundry.

Tablecontinuedfromlastpage

		DescriptionSettingOndisplay
		Add Clothes function is available in Wash phase on majority of the programs.Add clothes function is available also on program Rinse (only during first rinse on Rinse pro-gram).If water level is higher than al-lowed to open door, water will be pumped out.If temp is higher than 50°C, them add clothes option is not shown when pausing the program.
	No standby/Norm Standbychoic	Selection if appliance will go into Standby after 5min or not.
WiFisettings		By turning WiFi module On, the energy consumption will in-crease in standby mode.
ProgramsA-J	Settings can be changed on each program.	By changing settings it is pos-sible to create and customize your own program.Program can be renamed!

Cleaningandmaintenance

Cleaningthedetergentcompartmentanddoorrubbergasket

1

Press the tab to completely remove the detergent compartment from its housing.

2

Rinse and thoroughly clean the tray. You may also remove the cap from the plug in the conditioner compartment (A). Clean any residue from the cap and tube.

Clean the detergent compartment (B) interior. Replace the cap on the plug.

3

Use a brush to clean the nozzles on the upper side of the detergent compartment housing. After a washing program, nozzles that clean the interior of the dispenser are automatically switched on (only available in some models). Use a brush to clean the lower part of the detergent compartment housing.

4

Replace the detergent dispenser into its housing.

INFORMATION!

Close the detergent compartment!

INFORMATION!

Do not wash the detergent compartment in the dishwasher!

5

After every wash, wipe the rubber door seal to extend its useful life.

Cleaningtheapplianceexterior

Clean the appliance exterior and the display unit using a soft damp cotton cloth and water. Do not use solvents or abrasive cleaners that could damage the appliance (please observe the recommendations and warnings provided by the manufacturers of the cleaning agents).

INFORMATION!

Do not clean the washing machine with a jet of water!

Line drawing of a front-loading washing machine (no text or symbols)

ELECTRICSHOCK!

Always disconnect the washing machine from the power mains before cleaning.

In the case of a 3 phase connection of the appliance, switch off the main socket switch.

Cleaningthewashingmachineinterioragainstodours

Modern detergents often allow washing clothes at low temperatures. This means that residue may accumulate in the washing machine, which in turn could cause odours.

To avoid such odorous, we recommend running the self-cleaning program (Drum-cleaning) once per month. Use a small amount of powder detergent and do not put any laundry in the drum.

Cleaningtherinsingholes(undertheagitatorinthedrum)

If you believe that objects like nails or paper clips fell into the washing machine drum, check the area underneath the agitator. Such objects may rust (corrode) and cause stains on your clothes. Nails and other sharp objects can also cause holes in the fabric.

Proceedasfollows:

1

Insert a screwdriver or a similar tool into the slot in the rib and carefully push it to the left.

Tablecontinuedfromlastpage

Diagram showing a car interior with a sensor device and a numbered component (no text or symbols)

2

Hold the rib with the other hand and pull it towards you.

3

Lift the drum rib.

4

Remove any objects.

5

Place the rib into the installation slot indicated with "F" towards you. Make sure all ribs are firmly in place in their respective slots in the drum. Push the rib inwards (as indicated by the arrow in the figure) until it snaps.

If you are using hard water

If you are washing with hard water (causing limescale build-up), a greyish-white film may appear on the washing machine drum. To remove this film, add vinegar (approximately 2 dl or sodium bicarbonate "baking soda" (1 tablespoon or 15 g)) into the washing machine drum and select any program with a temperature of 90^ , or the Drum Cleaning program. See STEP 5: Choose the program.

Repeat the process as necessary.

Errors-whattodo?

Disturbances from the environment (e.g. the power grid) may result in various error reports (see Troubleshooting table). In such case:

• Switch off the appliance, wait for 1 minute, switch the appliance back on, and repeat the washing program.
• If the error occurs again, call an authorized service unit.
• You will be able to solve most of the problems in appliance operation by yourself (see Troubleshooting table).
  • Repairs may only be carried out by an adequately trained person.
• Repair or any warranty claim resulting from incorrect connection or use of the washing machine shall not be covered by the warranty. In such cases, the costs of repair shall be charged to the user.

INFORMATION!

The warranty does not cover the errors or failures resulting from disturbances from the environment (lightning strike, power grid failures, natural disasters etc.).

		Whattodo?CauseProblem/error
Washingmachine doordoesnot open.	Water level too high.	Drain the water using the Drain or Spinning program. See "Step 5: Choose the program".
	Water temperature in the washing machine is too high.	Wait for the water temperature to drop and pump out the water. If you still cannot open the door, use the emergency door opening tool (see chapter "ERRORS - WHAT TO DO? / Manual opening of washing machine door").
Washingprogram isnotinprogress.	The water in the inlet hose is not open.	Check that the water supply is properly connected and open.
	Washing machine door is not properly closed.	Firmly press on the washing machine door until you hear two clicks when it is closed.
	There is no voltage in the power outlet.	Check if the plug is connected to the power outlet and whether there is electric current (or voltage) in the outlet.
	Delayed start function has been selected.	To cancel the delayed start function, press the Start button and hold it for three seconds.

Tablecontinuedfromlastpage

		Whattodo?CauseProblem/error
Washingtimeis longerthananti-cipated(thetime isregularlyup-datedonthedis-playunit).	Low inlet water tempera-ure.	Program duration can be up to 60% longer than initially anticipated in the nor-mal progress.
	UKS* (*unbalance system) stability system engaged due to unevenly distrib-uted laundry.	Program time is extended due to the need to redistribute the laundry in the drum.
	Low mains voltage.	Washing machine needs more time be-cause the power mains voltage is too low.
	Power supply failure.	Program time is extended by the duration of the power supply failure.
Displaydoesnot lightup.	There is no voltage in the appliance.	Check if the plug is connected to the power outlet and whether there is electric current (or voltage) in the outlet.
Thewordingon thedisplayunitis notinyourlan-guage.	You have not selected your preferred language yet.	Choose the preferred language (see "STEP 5 / Settings / Choosing the lan-guage").
Wetlaundry ("unbalance"will appearondisplay)	A small amount of laundry will often be unevenly dis-tributed.	Loosen and redistribute the laundry and select the Drain or Spinning program.Increase the amount of laundry in the washing machine and restart the program (see "STEP 7: Start the wash / Adding or removing laundry after the start of the program").
Therearetraces ofgrease(or greaserolls)on theclothes.	The laundry was very greasy.	Wash the laundry again. When your laun-dry is this heavily soiled, add more wash-ing powder or use a liquid detergent in combination with a more powerful (longer) program.
Therearestill stainsonthelaun-dry.	You used bleach-free li- quid detergent or powder detergent for coloured laundry.	Use a detergent that contains bleach.
	You selected an unsuit-able program.	Use special stain removers.

Tablecontinuedfromlastpage

		Whattodo?CauseProblem/error
Therearewhite residuesofwashingpowderonthe laundry.	This is not due to poor rinsing by your washing machine, but rather due to phosphate-free detergents which contain ingredients (zeolites) for water softening. These ingredients may be deposited on the laundry.	Immediately rinse the laundry again.Use liquid detergents that do not contain zeolites.Try removing any residues with a brush.
Thereispowder detergentleftin themainwash compartmentof thedetergent compartment.	Water pressure not high enough.	Clean the net on the water supply hose.
	Some washing powders may stick strongly to the detergent compartment if it is empty.	Choose higher water level or extra rinse (see "STEP 6 / Choose program settings").Wipe the detergent compartment before adding the powder detergent.
Thereiscondition-erleftinthecondi-tionercompart-mentofthedeter-gentcompart-ment.	Plug cap is not positioned correctly or it is clogged.	Make sure the plug cap in the conditioner compartment of the detergent compa-ment is positioned correctly.Clean the plug cap (see chapter "CLEANING AND MAINTENANCE / Cleaning the detergent compartment").
Odourinthe washingmachine drum.	Residues of fabric, washing detergent, and condi-tioner in the filter.	Check if the filter is clean.
	Development of germs and bacteria.	Choose a self-cleaning (Drum Cleaning) program (see "STEP 5: Choose the pro-gram").
Machineismov-ingduringopera-tion.	Feet not adjusted cor-rectly.	Level the feet (see chapter "INSTALLA-TION AND CONNECTION / Adjusting the feet").
	Transport bolts not re-moved.	Remove the transport bolts (see chapter "BEFORE USING THE APPLIANCE FOR THE FIRST TIME /Transport protection").
Machineismov-ingduringspin-ning.	Unevenly distributed laun-dry or not enough laundry.	The washing machine will automatically decrease the spin speed if vibration is too strong.

Tablecontinuedfromlastpage

		Whattodo?CauseProblem/error
		• Increase the amount of laundry in the washing machine and restart the program (see "STEP 7: Start the wash / Adding or removing laundry after the start of the program").

Manualopeningofwashingmachinedoor

ELECTRICSHOCK!

Washing machine door may be opened manually if the appliance is not connected to the power mains and if the water has been pumped out of the machine.

A. Choose the Spinning or Drain program to pump the water from the machine. If this does not work, water has to be drained from the washing machine drum manually. See chapter "Cleaning the trap and drain pump" in the chapter "CLEANING AND MAINTENANCE".
B. Make sure the main switch is off and that the plug is disconnected from the power outlet. If you have a washing machine with a 3phase connection, do not pull the plug out of the power outlet.
C. Take the emergency door opening tool (found at the back of the detergent compartment) and insert it into the upper part of the slot on the right-hand side of the washing machine door latch.

Technical line drawing of a mechanical component with internal channels and a directional arrow (no text or symbols)

D. Press the key (key=the emergency door opening tool) downwards (all the way, until you hear a click) to unlock the washing machine door. When the door is unlocked, open it by pulling towards you.

Line drawing of a washing machine with two circular insets showing internal components and directional arrows (no text or symbols)

INFORMATION!

If the washing machine door still cannot be opened, call a service technician.

Failuredisplay

In case of a failure while a program is in progress, the relevant Error XX is indicated on the display unit.

Press the INFO button to display the error description.

Switch off the appliance and turn it back on.

Errors indicated on the display unit may include the following:

Error	displayunit	Whattodo?Errorindicationonthe
	Incorrect settingsE0	Restart the program. If the error reoccurs, call a service technician.
	Temperature sensor failureE1	Inlet water too cold. Repeat the washing program.If the appliance reports this error again, call a service technician.
	Door lock errorE2	Turn the appliance OFF and then switch it again ON. Start the program again. If the error reoccurs, call service technician.
E3	Water filling error	Check the following:is the water inlet valve open,is the filter on the water inlet hose clean,is the water supply hose deformed (clipped, clogged etc.),is the pressure in the water mains between 0.1 and 1 MPa (1–10 bar).Then, press theExitbutton to resume the program.If the error reoccurs, call a service technician.
	Water heating errorE6	Restart the program; if the error reoccurs, call a service technician.
E7	Water draining error	Check the following:is the drain hose clogged,is the drain clogged,is the drain hose fitted at the right height (see chapter on drain hose installation in the instruction manual).Then, press the Exit button again. If the error reoccurs, call a service technician.
E10	Water level sensor error	Turn the appliance OFF and then switch it again ON. Start the program again. If the error reoccurs, call service technician.

Tablecontinuedfromlastpage

Error	displayunit	Whattodo?Errorindicationonthe
	OverflowE11	If there is water in the drum that exceeds a certain level, and an error is reported on the display unit, the washing program will be interrupted and water will be pumped out of the washing machine. Restart the programme. If the error reoccurs, call a service technician.If there is water in the drum that exceeds a certain level, and an error is reported on the display unit, while the washing machine continues to add water, close the water tap and call a service technician.
E12	Motor error / motor control error	Restart the program; if the error reoccurs, call a service technician.
E23	Error while unlocking the door	Door is closed, but it cannot be unlocked. Turn off the washing machine, then turn it back on. If the error reoccurs, call a service technician. See instructions for opening the door - chapter on manual door opening.
E36	Error in UI** and PMCU communication.	Turn off the appliance and turn it back on. If the error reoccurs, call a service technician.
E37	PMCU/UI** software versions are not compatible	Call a service technician.
E40	Voltage value out of range.	Restart the program. If the error reoccurs, call a service technician.
E41	The value of frequency out of range.	Restart the program. If the error reoccurs, call a service technician.
	Unevenly distributed laundry.	Manually distribute the laundry and run the spinning program.
	Unable to lock door	Open and firmly close the door again to final position. If the error reoccurs, call a service technician.
	Warning -Self-cleaning program	Message "Sterile Tube alert" is displayed every 40 completed wash cycles. Use the self-cleaning program (DRUM CLEANING); see STEP 5.
	Preparing to door unlocking. (press INFO): Draining must be performed. Wait for door unlocking.	Wait for the process to finish. If no errors are shown after the process, a new cycle can be run.
	Water drain system alert	Alert about reduced water flow in the pumping stage. Please check user manuals.

** UI = (User Interface)

Unevenly distributed laundry or lumps of laundry in the washing machine drum may cause problems such as vibration and noisy operation. The washing machine will sense this and activate the UKS* (*unbalance system).

Smaller loads (e.g. one towel, one sweater, one bathrobe etc.) or clothes made of materials with special geometrical properties are virtually impossible to distribute evenly across the washing machine drum (slippers, large items etc.). This results in several attempts to redistribute the laundry, which in turn leads to longer program duration. In extreme cases of unfavourable conditions, the program can be completed without the spinning cycle.

UKS* (* unbalance system) allows stable operation and extends the useful life of the appliance.

Service

Beforecallingaservicetechnician

When you contact a service centre, please state the model (1), type (2), and serial number (3) of your washing machine.

Model, type, and serial number are indicated on the rating (type) plate located on the washing machine door casing.

WARNING!

In case of a failure, only use approved spare parts by authorized manufacturers.

WARNING!

Repair or any warranty claim resulting from incorrect connection or use of the washing machine shall not be covered by the warranty. In such cases, the costs of repair shall be charged to the user.

Line drawing of a front-loading washing machine with two doors open, showing internal compartments (no text or symbols)

Kontaktadress

Cylinda Service

0771-25 25 00

Du betalar endast lokal telefontaxa

www.cylinda.se

Technicalinformation

Energylabelling

Europeanteststandard	EN60456/ ^1*
Washing program	Eco 40-60 ^1*
	Cold water 15 °CConnection
	IEC-60704-2-4Noise testing method

Technicalinformation

	850 mmHeight
	595 mmWidth
	700 mmDepth
Weight	92/ 92,5 kg (depending on the model)
	80 IDrum volume
	See rating plateRated power
	See rating plateHeater power
	0,1-1 MPaWater pressure1-10 kp/cm ^2 10-100 N/cm ^2
Emission sound pressure level in accordance with EN ISO 11203	< 70 dB re 20 μPa
Material for the drum and dispenser	Stainless steel
Housing material	Hot-dip galvanized and powder coated sheet metal, or stainless steel sheet (depending on model)
Water connection	1,5 m, pex hose
Drain hose	1,6 m, polypropylene hose

Programchart

PT7840S

Program	Prewash	Temp.°C	Numberofrinses	Maximumload(kg)	Spinningspeed(rpm)	Waterconsumption(approximately,inlitres)			Powerconsumption(approximately,kWh)	Programduration(approximately,inhours andminutes)
						Hot	Cold	Sum
	√									2:081,388377614008
	√									2:282,388377614008
										1:250,147367614008
										1:280,487361121400
										1:380,588169121400
										2:002,788169121400
										0:500,435341121400
										1:001,506262140082
										1:000,603434140042
										0:380,204838101200
										0:350,084034680032
										0:290,072828140082
		Spinning				14008/				0:170,06
	Drain					/8/				0:010,01
	√									2:001,488882614008
	√									2:172,489082614008
										0:590,386452121400
										1:150,787260121400
	√									2:090,938074614008
	√									3:001,888882614008
	√									3:133,288882614008
										2:381,381029012140
										2:542,881029012140
										1:380,436856121200
										1:531,007664121200

Tablecontinuedfromlastpage

Program	Prewash	Temp.°C	Numberofrinses	Maximumload(kg)	Spinningspeed(rpm)	Waterconsumption(approximately,inlitres)			Powerconsumption(approximately,kWh)	Programduration(approximately,inhoursandminutes)
						Hot	Cold	Sum
										1:061,3085778/390CI
					14008Program	A
					14008Program	B
					14008Program	C
					14008Program	D
					14008Program	E
					14008Program	F
					14008Program	G
					14008Program	H
					14008Program	I
					14008Program	J

The above table includes several examples of the use of energy, water, and time for several different program settings. Actual consumption or duration may vary depending on the water pressure, water hardness, water inlet temperature, room temperature, weight and type of load, changes in power supply, and selected options or settings. In the examples specified here, the draining is set to Normal and no additional options are selected.

Maximum or nominal load applies to laundry prepared pursuant to the IEC 60456 standard.

√ Setting possible on the program

Adjustmentofthedisplayedwashingtime

Advanced technology allows the appliance to sense the amount of laundry and add the required amount of water during the washing process. Depending on the washing load, washing time can be longer or shorter and the time displayed will be adjusted accordingly.

Moreover, displayed washing time may change due to differences in inlet water temperature. At low inlet water temperatures, washing time can be longer; at higher temperatures, it can be shorter.

Unevenly distributed laundry or lumps of laundry in the washing machine drum can cause problems such as vibration and noisy operation. The appliance can sense such lumps and will try to redistribute the laundry. Smaller loads (e.g. one towel, one sweater, one bathrobe etc.) or clothes made of materials with special geometrical properties are virtually impossible to distribute evenly across the washing machine drum (slippers, large items etc.). This results in several attempts to redistribute the laundry, which in turn leads to longer program duration.

Removal

Disposal/recyclingofpackaging

Our product packaging is made of environmentally friendly materials that can be recycled,

disposed of, or destroyed without any hazard to the environment. To this end, packaging materials are labelled appropriately.

The symbol on the product or its packaging indicates that the product should not be treated as normal household waste. Take the product to an authorized collection centre for waste electric and electronic equipment processing.

When disposing of an appliance, at the end of its useful life, remove all power cords and destroy the door latch and switch to prevent the door from locking or latching (child safety).

Correct disposal of the product will help prevent any negative effects on the environment and health of people which could occur in case of incorrect product removal. For detailed information on removal and processing of the product, please contact the relevant authority in charge of waste management, your waste disposal service, or the store where you bought the product.

Service

Vi har service i hela Sverige/ Nationwide service in Sweden

Besök www.cylinda.se / Visit www.cylinda.se

Ring 0771-25 25 00 (endast lokaltaxa) / Call 0771-25 25 00

Uppge / Declare

Maskintyp / Model code

Serienummer / Serial number

Inköpsdatum / Purchase date

Problembeskrivning / Problem description