PRMC700.5 - Bill counter Pyle - Free user manual and instructions

USER MANUAL PRMC700.5 Pyle

Three grayscale images of different counting machines on a dark background (no text or symbols visible)

FULLY AUTOMATIC

Money Counter

Suitable for both new, old, dirty, tattered polymer bills and paper bills




Steps:

1. Loosen the protector screw (using a screwdriver, as shown in Figure 1) 2. Turning clockwise the adjustor screw to tighten the feeding nopper, shown in figure 2. 3. Turning counter clockwise the adjustor screw to loosen the feeding hopper, shown in figure 3. 4. After adjusting the correct level and counting performance is normal, tighten the protector screw (using a screwdriver), shown in figure 4. When adjusting the bill thickness adjustor screw does not solve the problem of improper bill Hand-hold a note. Put it inside the counting roller and resistant rubber, (see the picture). To test the tensile force. Clockwise direction is tighten, counter-clockwise direction is losing.  \* Tensile force test.

CONTENT

1. Illustration 2.General instruction. 2 3.Safety instructions 2 4.Power up 2 5. Counting function 2 6. Counterfeit detection 4-5 7. Fake money alarm 5 8.Error code and solution 6 9.Hopper adjustment 6-7 10 Counting roller replacement 8 11.Maintenance 8 12. Specification 8 13. Special function 14. Value counter special function 8 

FULLY AUTOMATIC

Money Counter

Suitable for both new, old, dirty, tattered polymer bills and paper bills \*SE7/25 then press "-" buttons to choose the desired Sensitivity level (range from 0-255). After choosing of the level "RESET" button to confirm. . \- By default, serving as a supplementary function, the detection can be activated when the unit is powered up. - If the machine detects a double-note when counting, it will stop and emit boeping sound, while the batch display will show the message "d3" (wistering the user the of the presence of a double-note). The double-note will always be the last one on the stacker. Remove the dubious bill press "RESET" button to continue. . --By default, serving as a supplementary function, the half-note detection can be activated when the unit is powered up. --If the machine detects a half-note when counting, it will stop and emit boeping sound, while the batch display will show the message "d5" alerting the user the presence of a half-note bill. The dubious bill will always be the last one on the stacker. Remove the dubious bill, press "RESET" button to continue the counting display will clear.

CAUTION:

1. It is highly recommended to contact the authorized service center or local dealer before you do the above adjustments. 2. Improper adjustments may cause improper working condition or false detection results.

7. Fake money alarm

When fake money pass the machine, the counting will stop and alarm. The function display will show the error code. The last note on the stacker normally is the fake money. The machine counting quantity number is not included in this note, remove the fake money. Press "RESET" button, the machine will start counting again.  - Fake money or questionable money 

FULLY AUTOMATIC

Money Counter

Suitable for both new, old, dirty, tattered polymer bills and paper bills

2.General instruction

On the basis of all our former models of banknote counter, we designed and developed this new model. It concentrates on all the advantages which the former models of banknote counter adopts and meanwhile develops more other advantages of its own kind. This model counts at a rate of 1100pcs/min for both PAPER&POLYMER notes. It includes UV/MG/MT counterfeit detection function: ADD and BATCH function Detect counterfeit banknotes during the counting procedure will save your time and money during your management accounting operations. It can be used in banks, shops, supermarkets, movie theaters, hotels, restaurants, etc. where the money is used. We recommend the user to verify the gift box contains all of the items listed here. 1. machine body 2. operation manual 3. bell(optional) 7. external diagnosis optionali

3.Safety instructions

--Read and understand all of the instructions and warnings both on the machine and manual. --Follow all warnings and instructions marked on the unit --This product should be operated only from the type of the power source indicated in the user's guide. If you are not sure of the type of power supply in your location, consult your dealer or local power company. \- Only use the cable provided with the unit. The use of other cable may result in electric shock, fire or cause serious damage to the wall. \- Never push objects of any kind into the unit through case slots, since they may touch dangerous voltage points or shortcut parts, resulting in a risk of fire or electric shock. --Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power supply cord or plug is damaged or trayed. b. If the liquid has been spilled into the unit. c. If the unit has been exposed to rain or water. d. If the machine has been dropped or the case has been damaged. e. If the product shows a noticeable change in performance. To reduce the risk of electric shock, do not disassemble this product. Take it 2 to qualified service personnel when service or repair work is in order to ensure that the equipment may be dangerous vollages or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used. Do not use the unit if the power cord is damaged or if the plug socket contact is loose. Don't follow these instructions may occur in electric socks, fire or other hazards. When unplugging the electric plug, do not pull it by the cord but rather to the plug and will pull it out. Don't follow those instruction may occur electric shock, fire or damage to the unit.

4.Power up

Connect the power cord to the machine (power outlet), then plug it to power source and turn the switch on; the unit will conduct a self-check by spanning the feeding roller while the MG and/or UV/IR functions will be automatically turned on by default. The counting display will show "if" when the unit is ready

5.Counting function

1>Counting Function

Once the bills are correctly placed in the hopper, the machine will start counting automatically (except in the manual counting mode). The number of counted bills will be shown on the counting display. Moreover, once the bills are removed from the stacker, the counting display will be clear and the batch display is turn will show the number of counted bills.

FULLY AUTOMATIC Money Counter

Suitable for both new, old, dirty, tattered polymer bills and paper bills

10. Counting roller replacement

When the counting roller damaged, it will cause counting not fluently or correct. Open the top cover, loosing the screw of roller axis machine. Replaced old roller. Then fix the machine inside.  • New model  - Old roller

11.Maintenance

-Do not operate the unit in areas with high temperature or high humidity since it may damage the machine. -When not using the unit for a long period of time, remove the power plug from the wall outlet. \- Never operate the unit under strong light. - Clean the machine frequently after switching off and unplugging of the machine. \- Do not use this product in areas where it may be exposed to water or other liquids. - Using this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaner. Use a brush or a damp cloth for cleaning.

12. Specification

Dimension:	360mm×260mm×165mm
Bankode Size:	40x70 x 100, Max: 80 x 190mm
Net Weight:	4.5kgs
Gross Weight:	5.0kgs
Counting Speed:	≥slant 1120pcs/min
Batch Range:	1-100
Counting Display:	LCD display or LED display
Power Supply:	AC 220V/50Hz, 120V/60Hz or DC85-250V
Power Consumption:	≤slant 70W

13. Special function

1. This model is with 790mm adjustable hopper to assure the counting 2. With chargable battery (Optional)

14. Value counter special function (Optional)

1. Value counting function Value counting function can be performed when turn on the machine. In this case, the note Qly: Qty. of each denomination and total amount of all the denominators will be shown on the display. UV/WM/MTN denetation function is action under value counting condition. 2. DEN function DEN function can be performed by pressing the "DEN" button to switch to counting function. In this case, when you put tips of other denomination inside of a button. It will be sorted under DEN function. For example, when you put 96pc 100 denomination note and 7pc 50 denominations note inside in the middle, it will be sorted under DEN function, the same condition for other denomination.  FULLY AUTOMATIC Money Counter Suitable for both new, old, dirty, tattered polymer bills and paper bills 1. Illustration  FULLY AUTOMATIC Money Counter Suitable for both new, old, dirty, sattered polymer bills and paper bills

8.Error code and solution

The batch display may show some error code when counting, which means there are some problems with the machine. Refer to the following diagram to find way to solve it.

Message	Error	Solution
d1	Supersonic bell detected by UV system.Problem in the UV system.	Remove the suspicious bell on the stacker press “RESET” to continue. Lower the UV sensitivity.
d2	Supersonic bell detected by UV system in the MGMT system.	Remove the suspicious bell on the stacker press “RESET” to continue. Lower the MGMT system.
d3	Double note detected by UV system.Problem in the UV system.	Remove the suspicious bell on the stacker press “RESET” to continue. Lower the IR sensitivity.
d4	Note of size problem detected by size detection system.Problem in the size detection system.	Remove the suspicious bell on the stacker press “RESET” to continue. Lower the size checking sensitivity.
d5	Full note detected by small detection system.Problem in the full note detection system.	Remove the suspicious bell on the stacker press “RESET” to continue.
d6	Simple step detection by size detection system.Problem in the small step detection system.	Remove the bell from the stacker. Press “RESET” to continue.
d7	Chain note detected by chain detection system.Problem in the chain note detection system.	Remove the bell from the stacker. Press “RESET” to continue.

Message	Error	Solution
EO1	Problem with the left counting sensor	Clean the sensor or replace it
EO2	Problem with the right counting sensor	Clean the sensor or replace it
EO3	Problem with the speed sensor	Clean the sensor or replace it
EO4	Problem with the auto start sensor	Clean the sensor or replace it
EOS	Problem with the preset sensor	Clean the sensor or replace it
EIO	Problem with the UV sensor	Clean the sensor or replace it

NOTE Generally speaking, most of the above-mentioned problems may be caused by dust or dirt inside of the machine. So keeping the machine clean is highly recommended. (1) 2017年1月1日至2018年1月1日，公司与关联方累计发生关联交易的总金额为人民币4,000万元。

9.Hopper adjustment

\- When improper feeding of bills occur, adjust the feeding thickness setting in the hopper by turning the adjustor screw located in the back of the machine to ensure proper feeding. 

instead.

Bills should be correctly placed as indicated in the following steps: Place the bills between the counting guides as shown in the figure 1, then push the bills backward to make them lay on the top of the hope plate, in the correct counting position as shown in the figure 2.  Figure 1: Put the bills by this direction Figure 2: Push the bills back < NOTE > The counting mode can be changed between Automatic and Manual. Press the "AUTO" button, if the batch display shows "AUTO" the machine is in automatic counting mode; if within the "AUTO" shown in the display, the machine is in manual counting mode, under this manual mode, press the "RESET" button after placing the bills to start counting.

2>Addition Function

Addition function can be performed by pressing the "ADD" button (the ADD indicator will appear). In this case, removing the counted bills from the stack will not clear the quantity counted and shown on the counting display. The next bills placed in the hopper will be counted and added to the preceding quantity. The total amount of added bills will be shown on the counting screen. Press the "ADD" button to close the function and clear the counting display.

3>Batch Function

The precast batch function can be performed by pressing the "BATCH" button (the BATCH indicator will appear). By default, when pressing the "BATCH" button, the batch function is turn on. The batch number can be set in amounts between 10 and 999 by pressing No. "-" & "-" button. To clear this function, press the "BATCH" button until the indicator is off. \- Under the batch counting mode, once the hopper is loaded, the machine will start counting and stop when the counted quantity reaches the preset batch one. To repeat the batch counting operation under the same preset batch quantity, just remove the counted bill from the stacker. The unit will batch the next group of bills under the same settings. If you wish to keep batching without removing the preset number, press the "RESET" button. --If the counted number does not equal with the preset batch number, the counter display will show the quantity with blinking number. --When counting with MG and/or UV detection on, the machine will stop automatically when detecting counterfeit currency. This function can be resumed by removing the dubious bill from the stacker and pressing "RESET" button.

6. Counterfeit Detection

\- 由于对价格变化因素的衍生品的市场波动及EV预估值 --The UV function is automatically turned on by default when the machine is powered up. It can also be selected or deselected by pressing the "CE" button located in the function console. if the machine detects a counterfeit note when counting, it will stop and emit beeping sound, while the batch display will show the message "d1" and the UV indicator will bunk (alerting the user of the presence of a dubious bill). The dubious bill will always be the last one on the stacker. Remove the dubious bill, press "RESET" button to continue. \- The sensitivity of UV detection can be adjusted. Hold "BATCH" button for 3 seconds, the batch display will show the current sensitivity level "SE4/120", then keep press "+"- "->" button to choose the desired sensitivity level (range from 0-200). After check the level, press "RESET" button to confirm/save. Do not change other versioned settings, change other settings may cause improper working condition. —The smaller number means the higher sensitivity you set and "0" means deactivate this detection function. —used to check all kinds of banknotes which contains the mentioned features. --The MG/MT function is automatically turned on by default when the machine is powered up. It can also be selected or deselected by pressing the "CF" button located in the function console. - If the machine detects a counterfeit nut when counting, it will stop and emit beeping sound, while the batch display will show the message "d2" and the MO/MT indicator will bind (starting the user the presence of a dubious bill). The dubious bill will always be the last one on the stacker. Remove the dubious bill, press "RESET" button to continue. --The sensitivity of MG detection can be adjusted. Held "BATCH" button for 3 seconds until the batch display will show the current sensitivity level "SE5/5." press "+"- "+-" button to choose the desired sensitivity level (range from 0-50). After choosing the level, press RESET\* button to confirm save. Do not change other unmentioned settings, changing other setting may cause improper working condition. The bigger number means the higher sensitivity you set and "0" means deactivate this detection function. --The UV and MG/MT detection can be used at the same time while counting to multiply the chances of detecting a counterfeit bill. By default, the UV and MG/MT detection functions are automatically turned on when the unit is powered up. Those functions can also be selected or deselected by pressing "CF" buttons. —Used to choose all funds of the National Bank with additional financial products. --By default, serving as a supplementary function, the IR detection can be activated when the unit is powered up. --The sensitivity of IR detection can be adjusted. Hold "BATCH" button for 3 seconds, the batch display will show the current sensitively level. Note: Hold "BATCH" button for 3 seconds, "SES" is used to adjust "MG1" sensitivity level, "SES" is used to adjust "MG2" sensitivity level.