Intimidator Hybrid 251SR - Lighting Chauvet - Free user manual and instructions

Product Type	Moving Head Hybrid Lighting Fixture
Dimensions (L x W x H)	12.6 x 8.6 x 21.6 in (322 x 220 x 549 mm)
Weight	35.6 lb (16.1 kg)
Power Supply	Switching (internal), 100-240 VAC, 50/60 Hz, auto-ranging
Power Consumption	358 W (120 V) / 344 W (230 V)
Light Source	Osram SIRIUS HRI® 251 W discharge lamp, 3,000 hrs lifespan
Zoom Angle	Beam: 1°–3°, Spot: 12°–23°, Wash: 7°–19°
DMX Channels	13 or 19 channels (selectable)
Pan Range	540°, 360°, or 180° (selectable)
Tilt Range	270°, 180°, or 90° (selectable)
Gobo Wheels	1 static wheel (16 gobos + open), 1 rotating wheel (8 gobos + beam + open)
Prisms	5-facet and 6-facet (rotating)
Frost	Variable frost (0–100%)
Focus	Motorized, with auto-focus options
Strobe Rate	0–20 Hz
Control Options	DMX, standalone (auto, sound, manual), master/slave, RFC-XL remote
Power Linking	Up to 3 units at 120 V, up to 5 units at 230 V
Connectors	3-pin and 5-pin DMX in/out, powerCON-compatible power in/out
Mounting	Overhead or surface, with safety cable requirement
Cooling	Convection (fans)
Maximum Ambient Temperature	104 °F (40 °C)
Cleaning Frequency	At least twice a month; gobo cleaning every 4 months
Fuse	T6.3 A, 250 V (user-replaceable)
Included Accessories	Power cable, hanging bracket, quick reference guide

Frequently Asked Questions - Intimidator Hybrid 251SR Chauvet

How do I replace the lamp in the Intimidator Hybrid 251SR?

Disconnect power and allow lamp to cool. Remove both head covers by loosening 4 screws on each side. Lift the lamp enclosure cover, tilt the lamp against the tension plates to free its rim. Remove power cables from contact leads. Install new lamp (Osram SIRIUS HRI 251W) and reconnect cables. Ensure the lamp is centered, close cover, and reattach head covers. Always wear gloves to avoid grease on the bulb.

How do I clean the product and gobos?

For external cleaning, unplug and wait for room temperature. Use vacuum or dry compressed air with a soft brush. Clean transparent surfaces with mild soap or ammonia-free glass cleaner on a soft cloth. For gobos, remove gobo holders every 4 months, clean gobos with ammonia-free glass cleaner, submerge holders in lubricant (e.g., WD-40), shake, brush, wipe, and apply synthetic oil to bearings. Reinstall properly.

How do I set the DMX starting address?

Press , use arrow keys to select Address, press , use arrows to choose a value from 001–512, press . Ensure the address does not conflict with other fixtures by considering the number of DMX channels used (13 or 19).

Can I use the Intimidator Hybrid 251SR without a DMX controller?

Yes. The fixture supports standalone modes: Auto (built-in programs), Sound (reacts to bass/drums), and Manual (program up to 2 steps with pan, tilt, color, etc.). Set via menu: Run Mode > Auto, Sound, or Manual. Also works in Master/Slave mode for synchronized operation.

How do I bind the RFC-XL remote to the fixture?

Press until Setup appears, press , select RF, press . The display shows Bind. Press . On the RFC-XL remote, press and hold ON/OFF for 5 seconds. The fixture will bind. To use in group mode, set Run Mode > RF > select RF 1–4 (group) or RFP (public).

What is the maximum number of fixtures I can power link?

At 120 VAC, you can power link up to 3 units. At 230 VAC, up to 5 units. Use the power outlet on the back of the product. Ensure total current does not exceed 12 A. Also, set ignition delays to avoid high inrush currents: first fixture at least 5 seconds, each subsequent at least 5 seconds more.

How do I factory reset the fixture?

Press , use arrows to select Setup, press , select Factory Set, press . Confirm by selecting YES. This restores all settings to default. Alternatively, you can use Reset to reset all functions without resetting settings.

What should I do if the lamp does not turn on?

Check that the lamp is properly installed and the fuse is not blown. Ensure the fixture is powered on and the lamp setting is enabled: Setup > Lamp Setting > On/Off > ON. Also check if lamp is controlled via DMX: if Off Via DMX is YES, DMX channel 18 must send a value 088–095 to turn lamp on. Verify ignition delay is appropriate.

How do I adjust the gobo focus?

In manual mode, you can adjust focus via the menu: Run Mode > Manual > select step > choose Focus and set value 000–255. DMX channels 12 (focus) and 13A (auto focus) control focus. For precise adjustment, use the Zero Adjust Mode (passcode 2323) to calibrate focus positions for rotating and static gobos.

What are the gobo dimensions and how do I replace a gobo?

Rotating gobos have outside diameter 13.7 mm, image diameter 10 mm. To replace: disconnect power, open head cover, push gobo holder toward front of head to disengage, pull out holder. Remove expansion ring, replace gobo, reinstall ring. Slide holder under pressure plate and push inwards until it clicks. Always use aluminum or glass gobos of same dimensions.

USER MANUAL Intimidator Hybrid 251SR Chauvet

Edition Notes

The Intimidator Hybrid 251SR User Manual includes a description, safety precautions, installation, programming, operation, and maintenance instructions for the Intimidator Hybrid 251SR as of the release date of this edition.

Trademarks

Chauvet, Chauvet DJ, the Chauvet logo, and Intimidator are registered trademarks or trademarks of Chauvet & Sons, LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other company and product names and logos referred to herein may be trademarks of their respective companies.

Copyright Notice

The works of authorship contained in this manual, including, but not limited to, all designs, text, and images are owned by Chauvet.

© Copyright 2024 Chauvet & Sons, LLC. All rights reserved.

Electronically published by Chauvet in the United States of America.

Manual Use

Chauvet authorizes its customers to download and print this manual for professional information purposes only. Chauvet expressly prohibits the usage, copy, storage, distribution, modification, or printing of this manual or its content for any other purpose without written consent from Chauvet.

Document Printing

For best results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If using A4 paper (210 x 297 mm), configure the printer to scale the content accordingly.

Intended Audience

Any person installing, operating, and/or maintaining this product should completely read through the guide that shipped with the product, as well as this manual, before installing, operating, or maintaining this product.

Disclaimer

Chauvet believes that the information contained in this manual is accurate in all respects. However, Chauvet assumes no responsibility and specifically disclaims any and all liability to any party for any loss, damage, or disruption caused by any errors or omissions in this document, whether such errors or omissions result from negligence, accident, or any other cause. Chauvet reserves the right to revise the content of this document without any obligation to notify any person or company of such revision; however, Chauvet has no obligation to make, and does not commit to make, any such revisions.

Document Revision

Go to www.chauvetdj.com for the latest version.

Revision Date Description

1 09/2024 Initial release.

TABLE OF CONTENTS

1. Before You Begin .... 1

What Is Included 1

Unpacking Instructions.... 1

Claims 1

Text Conventions 1

Symbols 1

Safety Notes.... 2

2. Introduction.... 3

Product Overview.... 3

Product Dimensions 4

3. Setup.... 5

AC Power 5

Fuse Replacement 5

Power Linking.... 5

Mounting 6

Orientation.... 6

Rigging 6

Lamp Replacement 7

Lamp Adjustment 8

Maintaining Lamp Lifespan 8

Gobo Wheels 9

Rotating Gobo Dimensions 9

Gobo Replacement 10

Procedure 10

Gobo Replacement Diagrams 10

4. Operation.... 11

Control Panel Operation.... 11

Menu Map 11

DMX Configuration.... 13

Starting Address.... 13

DMX Personalities.... 13

DMX Channel Assignments and Values 14

DMX Charts 14

Standalone Configuration.... 18

Auto Mode 18

Sound-Active Mode 18

Sound Sensitivity 18

Manual Mode 19

Program Manual Mode Step.... 19

Clear Manual Mode Step.... 19

Delete Manual Mode Step 19

Manual Mode Crossfade 19

Manual Mode Hold Time 19

Settings Configuration.... 20

Pan Reverse 20

Tilt Reverse 20

Screen Reverse 20

Pan Angle.... 20

Tilt Angle 20

Totem Mode 21

Lamp Settings 21

Manual Lamp Control 21

Lamp State at Power On 21

Lamp Control Via DMX 21

On if DMX is On.... 22

Off if DMX is Off.... 22

Ignition Delay at Power On 22

Low Power Delay with Shutter Closed.... 22

Reset Lamp Timer 23

Maintenance Timer 23

Maintenance Timer Interval 23

Reset Maintenance Timer 23

DMX Loss.... 23

Indicator 23

Flash if DMX.... 24

USB Update 24

Reset 24

Factory Reset 24

System Information 24

Master/Slave Mode 25

RFC-XL Remote Control 25

RFC-XL Remote Binding.... 25

RFC-XL Control Options 25

RFC-XL Remote Control Operation 26

Zero Adjust Mode.... 27

1. Maintenance.... 28

Product Maintenance 28

Gobo Maintenance.... 28

1. Technical Specifications.... 29

Contact Us.... 30

Warranty & Returns.... 30

1. Before You Begin

What Is Included

• Intimidator Hybrid 251SR
- Power cable
- Hanging bracket
- Quick Reference Guide

Unpacking Instructions

Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition.

Claims

If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet. Failure to report damage to the carrier immediately may invalidate a claim. In addition, keep the box and contents for inspection.

For other issues, such as missing components or parts, damage not related to shipping, or concealed damage, file a claim with Chauvet within 7 days of delivery.

Text Conventions

Convention Meaning

1–512 A range of values

50/60 A set of values of which only one can be chosen

Settings A menu option not to be modified

A key to be pressed on the product's control panel

ON A value to be entered or selected

Symbols

Symbol Meaning
		Electrical warning. Not following these instructions may cause electrical damage to the product, accessories, or the user.
		Critical installation, configuration, or operation information. Not following these instructions may make the product not work, cause damage to the product, or cause harm to the operator.
		Important installation or configuration information. The product may not function correctly if this information is not used.
		Pinch point warning.
		Useful information.

Safety Notes

These Safety Notes include important information about installation, use, and maintenance of the Intimidator Hybrid 251SR.

■ ALWAYS:

◆ Connect to a grounded circuit.
- Connect to operating voltages as specified on the product's spec sticker.
♦ Disconnect from power before replacing the fuse.
♦ Disconnect from its power source during periods of inactivity.
◆ Use a safety cable when suspending overhead.
- Heed all restrictions and warnings on the spec sticker.
◆ Mount in a location with at least 20 in (50 cm) of ventilation.
♦ Replace the fuse with the same type and rating.
Use a clamp with a captive bolt when a single hanging bracket is used.

■ In the event of a serious operating problem, stop using immediately.

■ DO NOT:

◆ Open this product or attempt any repairs. It contains no user-serviceable parts.
◆ Look at the light source when the product is on.
◆ Use if the power cable is crimped or damaged.
♦ Disconnect by pulling on the power cable.
◆ Allow flammable materials close to the product when it is operating.
◆ Touch the housing when it is on.
◆ Block any ventilation holes/slots in the housing.
◆ Connect to a dimmer or rheostat.
- Carry the product by its power cable.
♦ Operate in temperatures higher than 104°F (40°C).
♦ Expose to environments that exceed the Ingress Protection (IP) rating.
♦ Expose to rain or moisture.
Use outdoors.
Submerge.

Keep this User Manual for future use. If the product is sold to someone else, be sure that they also receive this document.

2. Introduction

Product Overview

# Name # Name
1 LCD display 6 USB type C port
2 Safety loop 7 Carry handles
3 Menu buttons 8 5-pin DMX in/out
4 LED indicator 9 3-pin DMX in/out
5	Fuse holder	10	Power out/in

WARNING! The USB type C port is ONLY for software updates. Using it for any other purpose may cause damage to the product.

Product Dimensions

3. Setup

AC Power

The Intimidator Hybrid 251SR has an auto-ranging power supply and it can work with an input voltage range of 100 to 240 VAC, 50/60 Hz.

To determine the product's power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product's back panel, or refer to the product's specifications chart. The listed current rating indicates the product's average current draw under normal conditions.

• Always connect the product to a protected circuit (a circuit breaker or fuse). Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.

Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel serves only as a 0 to 100% switch.

Fuse Replacement

1. Disconnect the product from power.
2. Using a flat-head screwdriver, unscrew the fuse holder and pull it straight out.
3. Remove the blown fuse from the holder and replace with a fuse of the exact same type and rating.
4. Re-insert the fuse holder and reconnect power.

Disconnect the product from the power outlet before replacing the fuse.

Always replace a blown fuse with one of the same type and rating.

Power Linking

This product provides power linking via the outlet located in the back of the product. See the diagram below for further explanation.

Power Linking Diagram

It is possible to link up to 3 Intimidator Hybrid 251SR products on 120 VAC or up to 5 products on 230 VAC.

The power linking diagram shown above corresponds to the North American version of the product ONLY! If using the product in other markets, consult with the local Chauvet distributor as power linking connectors and requirements may differ by country or region.

Mounting

Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes.

Orientation

The Intimidator Hybrid 251SR may be mounted in any position; however, make sure adequate ventilation is provided around the product.

Rigging

• Before deciding on a location for the product, always make sure there is easy access to the product for maintenance and programming.
• Make sure that the structure and attachment points can support the weight before hanging the product (see the Technical Specifications section for weight information).
• When mounting the product overhead, always use a safety cable. Mount the product securely to a rigging point, such as an elevated platform or a truss.
• When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity. The bracket has a 13-mm hole, which is appropriate for this purpose.
• The bracket adjustment knobs allow for directional adjustment when aiming the product to the desired angle. Only loosen or tighten the bracket knobs manually. Using tools could damage the knobs.
• When power linking multiple products, mount the products close enough for power linking cables to reach.
• When mounting the product on the floor, make sure that the product and cables are away from people and vehicles.

Mounting Diagram

Overhead mounting Surface mounting

To prevent accidental loosening when using a single mounting clamp, be sure to use a clamp with a captive bolt.

Lamp Replacement

The Intimidator Hybrid 251SR is equipped with a 251 W Osram HRI® discharge lamp. Follow the procedure below to safely replace the lamp.

• Disconnect the product from AC power before opening.
• DO NOT power the product on without a lamp installed.

• DO NOT touch the lamp without wearing gloves. Leaving grease on the bulb or contacts could reduce the lamp's life.

• Remove the product from power and allow several minutes for the lamp to cool.

• Remove both head covers by loosening 4 screws on each side with a Phillips-head screwdriver.
• Lift the cover of the lamp enclosure to gain access.
• Tilt the lamp against the metal tension plates to free its rim from the slot on the other side.
• Gently remove the lamp and uninstall the power cables from the contact leads.
• Install the power cables to the contact leads of the new lamp.
• Push the new lamp against the metal tension plates so that its rim can slide under the slot on the other side. Ensure the lamp is centered in the assembly.
• Close the cover of the lamp enclosure and reinstall both head covers.

Lamp Adjustment

To ensure the lamp is positioned correctly, it is necessary to adjust it after installation with the lamp adjustment knob. To access the lamp adjustment knob:

1. Ensure the product is stationary.
2. Remove both head covers by loosening 4 screws on each side with a Phillips-head screwdriver.
3. Adjust the position of the lamp by turning the lamp adjustment knob clockwise or counterclockwise with a flat-head screwdriver.

Lamp adjustment knob

DO NOT touch the lamp, any electrical contact, or wire while the product is powered. Practice safety precautions at all times while working on powered electronics.

Ensure the moving head is stationary before performing this procedure.

Maintaining Lamp Lifespan

Observe the following to preserve the quality and lifespan of the Intimidator Hybrid 251SR lamp:

ALWAYS turn the lamp off by using the DMX controller or the product's control panel, then wait at least 5 minutes before switching off the product. This will keep the fans running to extract any remaining heat from the product's head.

• DO NOT power cycle the product unless it is necessary.
- DO NOT touch the lamp without wearing gloves. Leaving grease on the bulb or contacts could reduce the lamp's life.
- ALWAYS change the lamp when it has reached its recommended lifespan to avoid the risk of lamp explosion.

Gobo Wheels

Gobo 2 (Rotating)

Rotating Gobo Dimensions

Gobo Replacement

The gobos in the Intimidator Hybrid 251SR are removable from their gobo holders.

- Make sure to disconnect the product's power cable before replacing a gobo.

• Always replace a gobo with a gobo of the same dimensions.

- When inserting a glass gobo, always make sure that the shiny side of the gobo (glass base) faces the lamp. This provides a layer of protection against the high temperature from the lamp.

- All custom gobos in the Intimidator Hybrid 251SR gobo wheel must be aluminum or glass.

Procedure

Follow the recommended procedure below to remove or replace the gobos:

1. Turn the product off and disconnect it from the power outlet.
2. Open the head cover by loosening the 4 Phillips-head 1/4 -turn screws on the sides of the top cover.
3. Separate the gobo holder away from the gobo wheel by pushing it toward the front of the moving head (see direction 1 in the diagram). Be careful not to push the gobo out of the gobo holder.

4. Extract the gobo holder by pulling it outward (see direction 2 in the diagram).

5. On a flat surface, remove the expansion ring that holds the gobo in place and remove the gobo from the gobo holder.

6. Insert a new gobo and hold it in place with the expansion ring.

7. Slide the tip of the gobo holder under the pressure plate near the center of the gobo wheel.

8. Push the gobo holder inwards. DO NOT force the gobo holder into the gobo wheel slot. If correctly installed, the gobo plate should easily slide itself into the gobo wheel slot.

Gobo Replacement Diagrams

- Gobo illustrations are for reference purposes only. Gobo designs may differ from those installed in the product.

• S e e Gobo Main instructions on how to clean the gobos and gobo holder.

4. Operation

Control Panel Operation

To access the control panel functions, use the four buttons located underneath the display. Please refer to the Product Overview to see the button locations on the control panel.

Button Function

	Press to find an operation mode or to back out of the current menu option
	Press to scroll up the list of options or to find a higher value
	Press to scroll down the list of options or to find a lower value

Press to activate a menu option or a selected value

Menu Map

Refer to the Intimidator Hybrid 251SR product page on www.chauvetdj.com for the latest menu map and software.

Main Level	Programming Levels Description
Address 001-512 Sets the DMX starting address
Run Mode	DMX	13CH			Selects DMX mode
		19CH
	Slave Slave1-4 Selects Slave mode 1, 2, 3, or 4
	Auto Selects Auto mode
	Sound Selects Sound-Active mode
	RF	RF 1-4			Sets the product to work with the RFC-XL remote in group 1, 2, 3, or 4 (RF remote must be bound to the product first)
		RFP			Sets the product to work with public RF signal
	Manual	Crossfade (sec)		0000-1200	Sets the speed of playback in seconds
		Hold time (sec)		0001-1200	Sets the time between playback in seconds
		Step 1-2	Clear	NO	Resets all manual values of the selected step to 0
				YES
			Delete	NO	Removes the selected step from playback
				YES
			Pan	000-255	Manual pan control
			Tilt		Manual tilt control
			Color		Manual color control
			Gobo2		Manual static gobo control
			Gobo1		Manual rotating gobo control
			Gobo1 Rotate		Manual gobo rotation control
			Prism1		Manual 5-facet prism control
			Prism2		Manual 6-facet prism control
			Focus		Manual focus control
			Zoom		Manual zoom control
			Frost		Manual frost control
			Dimmer		Manual dimmer control
			Shutter		Manual shutter control

Main Level	Programming Levels			Description
Setup	Pan Reverse	OFF Normal pan operation
		ON Reverse pan operation
	Tilt Reverse	OFF Normal tilt operation
		ON Reverse tilt operation
	Screen Reverse	AUTO Automatic display orientation
		NO Normal display
		YES Reverse display
	Pan Angle	540 Selects the 540° pan angle range
		360 Selects the 360° pan angle range
		180 Selects the 180° pan angle range
	Tilt Angle	270 Selects the 270° tilt angle range
		180 Selects the 180° tilt angle range
		90 Selects the 90° tilt angle range
	Totem Mode	OFF Does not restrict the pan and tilt motion
		UP		Restricts the pan and tilt motion for overhead mounting
		DOWN		Restricts the pan and tilt motion for surface/floor mounting
	Sensitivity	001-100 Sets sound sensitivity
	Lamp Setting	On/Off	ON	Turns lamp on/off
			OFF
		State/Power On	OFF	Defines the status of lamp when powering up product
			ON
		Off Via DMX	NO	Enables lamp control through DMX
			YES
		On If DMX On	NO	Turns lamp on if DMX signal is detected
			YES
		Off If DMX Off	NO	Turns lamp off when DMX signal is lost
			YES
		Ignition Delay 000-255		Defines number of seconds after product powers on before lamp turns on
		Low Power Delay 000-255		Selects duration of delay between shutter closing and lamp entering low power mode
		Reset Lamp Time	NO	Resets lamp timer (for when lamp is replaced)
			YES
	Special Set	Interval 10-250		Defines number of hours between maintenance
		Remain Time	NO	Resets maintenance timer
			RESET
	DMX Loss	Hold Holds the last setting when signal is lost
		Black Blacks out the product when signal is lost
		Auto		Sets to Auto mode when signal is lost
		Sound		Sets to Sound mode when signal is lost
	Indicator	ON Enables LED indicator
		OFF Disables LED indicator
	Flash if DMX	ON Flash when there is DMX signal
		OFF Flash when there is no DMX signal
Setup (cont.)	RF BIND		Shows instructions on how to bind the RF remote to the product
	USB Update	NO	Enables/disables software update through USB-C
		YES
	Reset Resets the product
	Factory Set Loads factory defaults
Sys Info	Ver: V2.3 Displays the firmware version
	Running Mode:	____	Displays the current running mode
	DMX Address: ____	Displays the current DMX address
	Lamp On Time:	____	Displays how long the lamp has been running
	Remain Time:	____	Displays time remaining in maintenance cycle
	DFan1 Speed:	____	Displays fan information
	FSP_A Speed:	____
	FSP_B Speed:	____

DMX Configuration

The Intimidator Hybrid 251SR works with a DMX controller. Information about DMX is in the Chauvet DMX Primer, which is available from the Chauvet website chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf.

Starting Address

The Intimidator Hybrid 251SR uses up to 19 DMX channels in the 19CH DMX mode, which defines the highest recommended address to 494.

When selecting a starting DMX address, always consider the number of DMX channels the DMX mode uses. If the starting address is set too high, access to some channels could be restricted.

For information about the DMX protocol, download the DMX Primer from www.chauvetdj.com.

To select the starting address, do the following:

1. Press .
2. Use or to select Address.
3. Press .
4. Use or to select the starting address, from 001-512.
5. Press .

DMX Personalities

The Intimidator Hybrid 251SR has 2 DMX personalities, a 13-channel personality, and a 19-channel personality.

To select which DMX personality to use, follow the steps below:

1. Press .
2. Use or to select Run Mode.
3. Press .
4. Use or to select DMX.
5. Press .
6. Use or to select the DMX personality, from 19CH or 13CH.
7. Press .

DMX Channel Assignments and Values

DMX Charts

13CH	19CH	Function Value Percent/Setting
1 1	Pan 00	00 ⇔ 255 0–540°
-	2	Fine pan	000 ⇔ 255	Fine control of panning
2 3	Tilt 00	0 ⇔ 255 0–270°
-	4	Fine tilt	000 ⇔ 255	Fine control of tilting
-	5	Pan/Tilt speed	000 ⇔ 255	Pan/Tilt speed, fast to slow
3 6	Color wheel		000 ⇔ 003	White
			004 ⇔ 007	Red
			008 ⇔ 011	Orange
			012 ⇔ 015	Yellow
			016 ⇔ 019	Green
			020 ⇔ 023	Blue
			024 ⇔ 028	CTO
			029 ⇔ 033	Cyan
			034 ⇔ 038	Magenta
			039 ⇔ 043	Lime green
			044 ⇔ 048	Pink
			049 ⇔ 053	Lavender
			054 ⇔ 059	Ultraviolet
			060 ⇔ 187	Color indexing
			188 ⇔ 219	Color cycling rainbow, fast to slow
			220 ⇔ 223	Stop
			224 ⇔ 255	Reverse color cycling rainbow, slow to fast
4	7	Static gobo wheel(seeGobo Wheels)	000 ⇔ 002	Open
			003 ⇔ 005	Gobo 1
			006 ⇔ 008	Gobo 2
			009 ⇔ 011	Gobo 3
			012 ⇔ 014	Gobo 4
			015 ⇔ 017	Gobo 5
			018 ⇔ 020	Gobo 6
			021 ⇔ 023	Gobo 7
			024 ⇔ 026	Gobo 8
			027 ⇔ 029	Gobo 9
			030 ⇔ 032	Gobo 10
			033 ⇔ 035	Gobo 11
			036 ⇔ 038	Gobo 12
			039 ⇔ 041	Gobo 13
			040 ⇔ 044	Gobo 14
			045 ⇔ 047	Gobo 15
			048 ⇔ 050	Gobo 16
			051 ⇔ 054	Gobo 16 shake, slow to fast
			055 ⇔ 058	Gobo 15 shake, slow to fast
			059 ⇔ 062	Gobo 14 shake, slow to fast
			063 ⇔ 066	Gobo 13 shake, slow to fast
			067 ⇔ 070	Gobo 12 shake, slow to fast
			071 ⇔ 074	Gobo 11 shake, slow to fast
			075 ⇔ 078	Gobo 10 shake, slow to fast
			079 ⇔ 082	Gobo 9 shake, slow to fast
			083 ⇔ 086	Gobo 8 shake, slow to fast
			087 ⇔ 090	Gobo 7 shake, slow to fast
			091 ⇔ 094	Gobo 6 shake, slow to fast
			095 ⇔ 098	Gobo 5 shake, slow to fast
			099 ⇔ 102	Gobo 4 shake, slow to fast
			103 ⇔ 106	Gobo 3 shake, slow to fast
			107 ⇔ 110	Gobo 2 shake, slow to fast
			111 ⇔ 114	Gobo 1 shake, slow to fast
			115 ⇔ 127	Open
			128 ⇔ 189	Cycle effect, fast to slow
			190 ⇔ 193	Stop
			194 ⇔ 255	Reverse cycle effect, slow to fast
13CH	19CH	Function	Value	Percent/Setting
5	8	Rotating gobo wheel(seeGobo Wheels)	000 ⇔ 005	Open
			006 ⇔ 011	Beam mode
			012 ⇔ 017	Gobo 1
			018 ⇔ 023	Gobo 2
			024 ⇔ 029	Gobo 3
			030 ⇔ 035	Gobo 4
			036 ⇔ 041	Gobo 5
			042 ⇔ 047	Gobo 6
			048 ⇔ 053	Gobo 7
			054 ⇔ 063	Gobo 8
			064 ⇔ 073	Gobo 8 shake, slow to fast
			074 ⇔ 079	Gobo 7 shake, slow to fast
			080 ⇔ 085	Gobo 6 shake, slow to fast
			086 ⇔ 091	Gobo 5 shake, slow to fast
			092 ⇔ 097	Gobo 4 shake, slow to fast
			098 ⇔ 103	Gobo 3 shake, slow to fast
			104 ⇔ 109	Gobo 2 shake, slow to fast
			110 ⇔ 115	Gobo 1 shake, slow to fast
			116 ⇔ 127	Beam mode
			128 ⇔ 189	Cycle effect, fast to slow
			190 ⇔ 193	Stop
			194 ⇔ 255	Reverse cycle effect, slow to fast
6	9	G o b o r	000 No function
			001 ⇔ 063	Gobo indexing
			064 ⇔ 145	Rotation, fast to slow
			146 ⇔ 149	Stop
			150 ⇔ 231	Reverse rotation, slow to fast
			232 ⇔ 255	Bounce, slow to fast
7	1	0 P r i s m	000 ⇔ 007	No function
			008 ⇔ 012	5-facet prism
			013 ⇔ 130	Rotation, slow to fast
			131 ⇔ 247	Reverse rotation, slow to fast
			248 ⇔ 255	5-facet prism
8	1	1 P r i s m	000 ⇔ 007	No function
			008 ⇔ 012	6-facet prism
			013 ⇔ 130	Rotation, slow to fast
			131 ⇔ 247	Reverse rotation, slow to fast
			248 ⇔ 255	6-facet prism
9	12	Focus	000 ⇔ 255	Focus, big to small
10	13 A	Auto focus	000 ⇔ 010	No function
			011 ⇔ 126	Auto focus Gobo 1
			127 ⇔ 255	Auto focus Gobo 2
11	14	Zoom	000 ⇔ 255	Zoom out to zoom in
12	15 F	Frost	000 ⇔ 007	No function
			008 ⇔ 255	Frost, 0–100%
-13CH	1619CH	DimmerFunction Value Percent/Setting	000 ⇔ 255	0–100%
13	17	Shutter	000 ⇔ 007	Closed
			008 ⇔ 015	Open
			016 ⇔ 131	Strobe, slow to fast
			132 ⇔ 167	Slow open, fast close, slow to fast
			168 ⇔ 203	Fast open, slow close, slow to fast
			204 ⇔ 239	Pulse strobe, slow to fast
			240 ⇔ 247	Random strobe, slow to fast
			248 ⇔ 255	Open
-	18	Function	000 ⇔ 007	No function
			008 ⇔ 015	Blackout on pan/tilt movement
			016 ⇔ 023	Blackout on color wheel movement
			024 ⇔ 031	Blackout on gobo wheel movement
			032 ⇔ 039	Blackout on pan/tilt/color wheel movement
			040 ⇔ 047	Blackout on pan/tilt/gobo wheel movement
			048 ⇔ 055	Blackout on pan/tilt/color/gobo wheel movement
			056 ⇔ 087	No function
			088 ⇔ 095	Lamp On
			096 ⇔ 103	Pan reset
			104 ⇔ 111	Tilt reset
			112 ⇔ 119	Color wheel reset
			120 ⇔ 127	Gobo wheels reset
			128 ⇔ 135	Frost reset
			136 ⇔ 143	Prism reset
			144 ⇔ 151	Focus and zoom reset
			152 ⇔ 159	All reset
			160 ⇔ 167	Shutter reset
			168 ⇔ 231	No function
			232 ⇔ 239	Lamp Off
			240 ⇔ 255	No function
-	19	Movement macros	000 ⇔ 007	No function
			008 ⇔ 023	Movement macro 1
			024 ⇔ 039	Movement macro 2
			040 ⇔ 055	Movement macro 3
			056 ⇔ 071	Movement macro 4
			072 ⇔ 087	Movement macro 5
			088 ⇔ 103	Movement macro 6
			104 ⇔ 119	Movement macro 7
			120 ⇔ 135	Movement macro 8
			136 ⇔ 151	Sound-active movement macro 1
			152 ⇔ 167	Sound-active movement macro 2
			168 ⇔ 183	Sound-active movement macro 3
			184 ⇔ 199	Sound-active movement macro 4
			200 ⇔ 215	Sound-active movement macro 5
			216 ⇔ 231	Sound-active movement macro 6
			232 ⇔ 247	Sound-active movement macro 7
			248 ⇔ 255	Sound-active movement macro 8

Standalone Configuration

Set the product in one of the standalone modes to operate without a DMX controller.

Never connect a product that is operating in any standalone mode to a DMX string connected to a DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller.

Auto Mode

To run the Intimidator Hybrid 251SR in auto mode, follow the instructions below:

1. Press .
2. Use or to select Run Mode.
3. Press .
4. Use or to select Auto.
5. Press .

Sound-Active Mode

To run the Intimidator Hybrid 251SR in sound-active mode, follow the instructions below:

1. Press .
2. Use or to select Run Mode.
3. Press .
4. Use or to select Sound.
5. Press .

The product will only respond to low frequencies of music (bass and drums).

Sound Sensitivity

To set the sound sensitivity of the Intimidator Hybrid 251SR, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select Sensitivity.
5. Press .
6. Use or to increase or decrease the sensitivity, from 001–100.
7. Press .

Manual Mode

To run the Intimidator Hybrid 251SR manually through the display menu, follow the instructions below:

1. Press .
2. Use or to select Run Mode.
3. Press .
4. Use or to select Manual.
5. Press .

Program Manual Mode Step

To program one of the steps in manual mode, follow the instructions below:

1. Go to Manual Mode .
2. Use or to select which step to program, from Step 1-2.
3. Press .
4. Use or to select a value to edit, from Pan, Tilt, Color, Gobo2, Gobo1, Gobo1 Rotate, Prism1, Prism2, Focus, Zoom, Frost, Dimmer, or Shutter.
5. Press
6. Use or to increase or decrease the selected value from 000–255.
7. Press .

Clear Manual Mode Step

To set all values in a step to 000, follow the instructions below:

1. Go to Manual Mode.
2. Use or to select which step to clear, from Step 1-2.
3. Press .
4. Use or to select Clear.
5. Press .
6. Use or to select from NO (do not clear) or YES (clear).
7. Press .

Delete Manual Mode Step

To remove a step from playback, follow the instructions below:

1. Go to Manual Mode.
2. Use or to select which step to remove, from Step 1-2.
3. Press .
4. Use or to select Delete.
5. Press .
6. Use or to select from NO (do not remove) or YES (remove).
7. Press .

Manual Mode Crossfade

To set the time it takes to switch between steps, follow the instructions below:

1. Go to Manual Mode .
2. Use or to select Crossfade (sec).
3. Press .
4. Use or to increase or decrease the cross-fade time in seconds from 0000–1200.
5. Press .

Manual Mode Hold Time

To set the time either step is active before switching, follow the instructions below:

1. Go to Manual Mode.
2. Use or to select Hold time (sec).
3. Press .
4. Use or to increase or decrease the hold time in seconds from 0001–1200.
5. Press .

Settings Configuration

Pan Reverse

To set the pan orientation on the Intimidator Hybrid 251SR, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select Pan Reverse.
5. Press .
6. Use or to select OFF (normal pan orientation) or ON (reverse pan orientation).
7. Press .

Tilt Reverse

To set the tilt orientation on the Intimidator Hybrid 251SR, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select Tilt Reverse.
5. Press .
6. Use or to select OFF (normal tilt orientation) or ON (reverse tilt orientation).
7. Press .

Screen Reverse

To set the display orientation on the Intimidator Hybrid 251SR, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select Screen Reverse.
5. Press .
6. Use or to select AUTO (auto-detect orientation), NO (normal display orientation) or YES (reverse display orientation).
7. Press .

Pan Angle

To set the pan angle range on the Intimidator Hybrid 251SR, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select Pan Angle.
5. Press .
6. Use or to select from 540 (540°), 360 (360°), or 180 (180°).
7. Press .

Tilt Angle

To set the tilt angle range on the Intimidator Hybrid 251SR, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select Tilt Angle.
5. Press .
6. Use or to select from 270 (270°), 180 (180°), or 90 (90°).
7. Press .

Totem Mode

To activate the Totem mode, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select Totem Mode.
5. Press .
6. Use or to select OFF (normal range of motion), UP (restricts the pan and tilt motion for overhead mounting), or DOWN (restricts the pan and tilt motion for surface/floor mounting).
7. Press .

Lamp Settings

Manual Lamp Control

To turn the lamp on or off on the Intimidator Hybrid 251SR, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select Lamp Setting.
5. Press .
6. Use or to select On/Off.
7. Press .
8. Use or to select ON or OFF.
9. Press .

Lamp State at Power On

To define whether the lamp should be on or off when powering on the Intimidator Hybrid 251SR, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select Lamp Setting.
5. Press .
6. Use or to select State/Power On.
7. Press .
8. Use or to select OFF or ON.
9. Press .

Lamp Control Via DMX

To enable or disable the Intimidator Hybrid 251SR lamp from being controllable through DMX, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select Lamp Setting.
5. Press .
6. Use or to select Off Via DMX.
7. Press .
8. Use or to select NO or YES.
9. Press .

On if DMX is On

To set the Intimidator Hybrid 251SR lamp to be on when a DMX signal is present, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press
4. Use or to select Lamp Setting.
5. Press
6. Use or to select On if DMX On.
7. Press .
8. Use or to select NO or YES.
9. Press .

Off if DMX is Off

To set the Intimidator Hybrid 251SR lamp to be off when there is no DMX signal present, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select Lamp Setting.
5. Press .
6. Use or to select Off if DMX Off.
7. Press .
8. Use or to select NO or YES.
9. Press .

Ignition Delay at Power On

To set the amount of time after power on before the Intimidator Hybrid 251SR lamp turns on, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press
4. Use or to select Lamp Setting.
5. Press
6. Use or to select Ignition Delay.
7. Press .
8. Use or to increase or decrease the delay time, from 000–255 (0 seconds to 255 seconds).
9. Press .

Warning! When power linking this product, lamp ignitions must be offset to avoid high inrush currents. The ignition delay of the first product in a power linking chain must be set to no less than five seconds. The ignition delay of each subsequent product in the chain must be at least five seconds more than the previous product.

Low Power Delay with Shutter Closed

To set the amount of time after leaving the shutter closed before the Intimidator Hybrid 251SR lamp enters low power mode, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press
4. Use or to select Lamp Setting.
5. Press .
6. Use or to select Low Power Delay.
7. Press .
8. Use or to increase or decrease the delay time, from 000–255 (0 seconds to 255 seconds).
9. Press .

Reset Lamp Timer

To reset the record of how much time the Intimidator Hybrid 251SR lamp has spent powered on, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press
4. Use or to select Lamp Setting.
5. Press
6. Use or to select Reset Lamp Time.
7. Press
8. Use or to select NO or YES.
9. Press .

Maintenance Timer

Maintenance Timer Interval

To define the length of the maintenance cycle on the Intimidator Hybrid 251SR, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press
4. Use or to select Special Set.
5. Press
6. Use or to select Interval.
7. Press
8. Use or to increase or decrease the time, from 10–250 (10 hours to 250 hours).
9. Press .

Reset Maintenance Timer

To reset the Intimidator Hybrid 251SR maintenance timer, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select Special Set.
5. Press .
6. Use or to select Remain Time.
7. Press .
8. Use or to select NO or RESET.
9. Press .

DMX Loss

To set the action the Intimidator Hybrid 251SR will do when signal is lost, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select DMX Loss.
5. Press .
6. Use or to select Hold (holds the last setting), Black (blacks out the product), Auto (sets the unit to auto mode), or Sound (sets the unit to sound mode).
7. Press .

Indicator

To enable or disable the LED indicator, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select Indicator.
5. Press .
6. Use or to select OFF (disabled) or ON (enabled).
7. Press .

Flash if DMX

To set the when the LED indicator flashes, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select Flash if DMX.
5. Press .
6. Use or to select ON (LED flashing indicates there is a DMX signal) or OFF (LED flashing indicates there is no DMX signal).
7. Press .

USB Update

To enable or disable the USB update function, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press
4. Use or to select USB Update.
5. Press .
6. Use or to select NO (disabled) or YES (enabled).
7. Press .

Reset

To reset all functions on the Intimidator Hybrid 251SR, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press .
4. Use or to select Reset.
5. Press .

Factory Reset

To restore the Intimidator Hybrid 251SR to factory default settings, follow the instructions below:

1. Press .
2. Use or to select Setup.
3. Press
4. Use or to select Factory Set.
5. Press .

System Information

To view the system information on the Intimidator Hybrid 251SR, follow the instructions below:

1. Press .
2. Use or to select Sys Info.
3. Press .
4. Use or to see all data.

Master/Slave Mode

The Master/Slave mode allows a single Intimidator Hybrid 251SR product (the “master”) to control the actions of one or more Intimidator Hybrid 251SR products (the “slaves”) without the need of a DMX controller. The master product will be set to operate in standalone mode, while the slave products will be set to operate in slave mode. Once set and connected, the slave products will operate in unison with the master product.

Configure the products as indicated below.

Slave products:

1. Press .
2. Use or to select Run Mode.
3. Press .
4. Use or to select Slave.

5. Press .

6. Use or to select from Slave1, Slave2, Slave3, or Slave4.

7. Select Slave1 for 100% synchronized actions.

8. Select Slave2, Slave3, and/or Slave4 for delayed actions, creating a wave effect.

9. Press .

10. Connect the DMX input of the first slave product to the DMX output of the master product.

11. Connect the DMX input of the subsequent slave products to the DMX output of the previous slave product.

12. Finish setting and connecting all the slave products.

Master product:

1. Set the master product to operate in standalone mode.
2. Make the master product the first product in the DMX daisy chain.

• Configure all the slave products before connecting the master to the daisy chain.
• Never connect a DMX controller to a DMX string configured for Master/Slave operation because the controller may interfere with the signals from the master.
• Do not connect more than 31 slaves to the master.

RFC-XL Remote Control

The Intimidator Hybrid 251SR can be operated with an RFC-XL remote (sold separately).

For more information about using an RFC-XL remote, download the user manuals from www.chauvetdj.com

RFC-XL Remote Binding

To enable RF control, the product must bind to the RFC-XL. To bind the Intimidator Hybrid 251SR to an RFC-XL, follow the instructions below:

1. Press repeatedly until Setup shows on the display.
2. Press .
3. Use or to select RF.
4. Press .
5. Bind will show on the display. Press .
6. Press and hold on the RFC-XL for 5 seconds to link the fixture to that remote.

RFC-XL Control Options

The RFC-XL can control multiple products at once, whether in defined groups or in public mode. To set the Intimidator Hybrid 251SR to public RFC-XL control or to an RFC-XL group:

1. Bind the
2. Press repeatedly until
3. Use or to select Run Mode.
4. Press .
5. Use or to select RF.
6. Press .

7. Press .

8. Use or to select to control mode, from RF 1-4 (group 1-4) or RFP (public mode).

RFC-XL Remote Control Operation

RFC Button Function

Press to power the RFC-XL on or off

Color picker Use to select a color (does not correspond to colors printed on remote)

Press to cycle between groups 1–4 and public mode Press to turn off all lights until the button is pressed again Press to activate automatic mode, then use <^> or to select a program from 00-10 Press to activate sound-active mode or to increase or decrease speed or sensitivity <^> Press to increase the selected value, or to scroll up the list of options Press to decrease the selected value, or to scroll down the list of options Press to toggle strobe, then use <^> or to increase or decrease strobe speed from 00–20 Press then use <^> or to increase or decrease the dimmer Press then use <^> or to increase or decrease the color cycling rainbow speed Press then use <^> or to increase or decrease the gobo cycle speed. Press again to toggle gobo wheels Press to select toggle auto gobo change Press to toggle pan and tilt then use <^> or to increase or decrease the selected value Press then use <^> or to increase or decrease the UV value Press then use <^> or to increase or decrease the focus and zoom values together Press then use <^> or to increase or decrease the pan value Press then use <^> or to increase or decrease the tilt value Press to cycle through colors 000-012 Press to cycle through static gobos 000–017 then rotating gobos 018–028 including open and beam modes Press to select a prism then use <^> or to increase or decrease the selected prism value Press then use <^> or to increase or decrease the focus value Press then use <^> or to increase or decrease the zoom value Press then use <^> or to increase or decrease the gobo rotation value Press to stop all movement and color chasing  The RFC-XL remote will not respond to any inputs when Black Out is activated. If the remote does not respond when a button is pressed, try pressing . You may have inadvertently activated Black Out.

Zero Adjust Mode

The Intimidator Hybrid 251SR contains a passcode protected mode which allows the user to calibrate and adjust several of the product's operating parameters. In order to access this mode, do the following: 1. Press and hold for at least 3 seconds. 2. Use (increases the selected value) and (selects the next value) to enter the passcode: 2323. 3. Press . In this mode, the zero positions and levels for the following can be adjusted: Parameter Function

PAN Pan motor position

TILT Tilt motor position

COLOR Color wheel position

GOBO2 Static gobo wheel position

GOBO1 Rotating gobo wheel position

GOBO1 ROTATE Gobo rotation position

PRISM1 5-facet prism position

PRISM2 6-facet prism position

FOCUS-GOBO1 Focus position for rotating gobo

FOCUS-GOBO2 Focus position for static gobo

ZOOM Zoom position

FROST Frost position

SHUTTER Shutter position To adjust the zero position or level of one of these parameters, follow the instructions below: 1. Access the Zero Adjust mode. 2. Use or to select the parameter to be adjusted. 3. Press . 4. Use or to increase or decrease the selected value, from 000–255. 5. Press .

5. Maintenance

Product Maintenance

Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of the light source's life and/or mechanical wear. To maintain optimum performance and minimize wear, clean all lighting products at least twice a month. However, be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency. To clean the product, follow the instructions below: 1. Unplug the product from power. 2. Wait until the product is at room temperature. 3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external surface/vents. 4. Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl alcohol. 5. Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue. 6. Softly drag any dirt or grime to the outside of the transparent surface. 7. Gently polish the transparent surfaces until they are free of haze and lint.  Always dry the transparent surfaces carefully after cleaning them.  Do not spin the cooling fans using compressed air because they could be damaged.

Gobo Maintenance

To ensure optimal operation, 1) inspect and 2) clean gobos every four months. More frequent maintenance may be necessary if usage is higher. To inspect, remove each gobo holder and check if: - the holders are clean (free of dirt, grime, or gunk). - the gobos are properly installed in the holders. - all the bearings are in place. • the holders are rotating freely. To clean the gobos and the gobo holder, follow the instructions below: 1. Remove the gobos from the holder. 2. Clean the gobos with a soft, lint-free cotton cloth. Use an ammonia-free glass cleaner sprayed to a piece of lint-free cotton cloth to clean glass gobos. 3. Submerge the gobo holder (without the gobo installed) in a container with a liquid lubricant (i.e., WD40) and let it rest for a couple of minutes. 4. Shake the container with the gobo holder inside to help release/loosen any gunk/grime/dirt. 5. Take the gobo holder out of the container and clean it using a small nylon brush. 6. Wipe off all the lubricant from the gobo holder using a piece of lint-free cotton cloth. 7. Apply a small coat of synthetic oil (i.e., Liquid Bearings) to the bearings and rotate it thoroughly in both directions (needle tip applier recommended). Make sure the gobo holder is rotating freely and is not making any abnormal noise. 8. Reinstall the gobos in the gobo holder. Make sure the gobos are in the correct positions. 9. Reinstall the gobo holder in the unit.

6. Technical Specifications

Dimensions and Weight

Length Width Height Weight

12.6 in (322 mm) 8.6 in (220 mm) 21.6 in (549 mm) 35.6 lb (16.1 kg) Note: Dimensions in inches are rounded. Power

Power Supply Type Range Voltage Selection

Switching (internal) 100 to 240 VAC, 50/60 Hz Auto-ranging Parameter 120 V, 60 Hz 230 V, 50 Hz

Consumption 358 W	344 W
Operating Current	3.6 A	2.3 A
Power linking current (products)	12 A (3 products)	12 (5 products)
Fuse	T6.3 A, 250 V	T6.3 A, 250 V
Power I/O	U.S./Worldwide	UK/Europe
Power input connector	powerCON-compatible	powerCON-compatible
Power output connector	powerCON-compatible	powerCON-compatible
Power cable plug Edison (U.S.) Local Plug

Light Source

Type	Power	Lifespan
Osram SIRIUS HRI® discharge lamp	251 W	3,000 hours

Photometrics

Strobe Rate	Mode	Zoom Angle	Illuminance @ 5 m
0 to 20 Hz	Beam mode	1° to 3	500,411 lux
	Spot mode	12° to 23°	376,927 lux
	Wash mode	7° to 19°	8,038 lux

Thermal

Maximum External Temperature	Cooling System
104 °F (40 °C) Convection

DMX

I/O Connector Channel Range
3- and 5-pin XLR	13 or 19

Ordering

Product Name	Item Code	UPC Number
Intimidator Hybrid 251SR	08012335	781462226831

Contact Us

General Information Technical Support

Chauvet World Headquarters

Address: 3360 Davie Rd., Suite 509 Voice: [phone] Davie, FL 33314 Fax: [phone] Voice: [phone] Email: [e-mail] Fax: [phone] Toll Free: [phone] Website: www.chauvetdj.com

Chauvet U.K.

Address: Pod 1 EVO Park Email: [e-mail] Little Oak Drive, Sherwood Park Nottinghamshire, NG15 0EB Website: www.chauvetdj.eu UK Voice: [phone] Fax: [phone]

Chauvet Benelux

Address: Stokstraat 18 Email: [e-mail] 9770 Kruishoutem Belgium Website: www.chauvetdj.eu Voice: [phone]

Chauvet France

Address: 3, Rue Ampère Email: [e-mail] 91380 Chilly-Mazarin France Website: www.chauvetdj.eu Voice: [phone]

Chauvet Germany

Address: Bruno-Bürgel-Str. 11 Email: [e-mail] 28759 Bremen Germany Website: www.chauvetdj.eu Voice: [phone]

Chauvet Mexico

Address: Av. de las Partidas 34 - 3B (Entrance by Calle 2) Zona Industrial Lerma Lerma, Edo. de México, CP 52000 Voice: [phone] Email: [e-mail] Website: www.chauvetdj.mx

Warranty & Returns

For warranty terms and conditions and return information, please visit our website. For customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration. For customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and Germany: www.chauvetlighting.eu/warranty-registration.