MAG06V3 - Loudspeaker SONANCE - Free user manual and instructions

Product Type	Weather-Resistant Outdoor Speaker
Brand	Sonance
Model	MAG06V3
Speaker Type	2-way (Tweeter + Woofer)
Tweeter	1" (25mm) Cloth Dome, Ferrofluid Cooled, Acoustic Back Chamber
Woofer	6.5" (165mm) Glass Fiber Cone with Santoprene Surround
Frequency Response	65Hz - 30kHz ±3dB
Impedance	8 ohms nominal; 6 ohms minimum
Power Handling	5W minimum, 80W maximum
Sensitivity	89dB SPL (2.83V/1 meter)
Environmental Rating	IP-66 Waterproof, Mil Spec 810 (Humidity, Salt Spray, Temp, UV)
Operating Temperature	-13°F to 149°F (-25°C to 65°C)
Dimensions (WxHxD)	7.51" x 12.14" x 6.86" (191mm x 308mm x 174mm)
Grille Material	Perforated Aluminum
Shipping Weight (Pair)	14 lbs (6.4 kg)
Mounting System	FastMount Bracket System (Included)
Included Accessories	(2) Speakers, (2) Grilles, (2) Mounting Brackets, (2) Wire Terminal Covers, Mounting Hardware
Warranty	1-Year Limited (Non-Transferable)
Installation	Ear-level placement recommended; wall, pole, corner, eave mount
Connection	Spring-loaded terminals, accept up to 14 AWG wire
Maintenance	Clean with damp cloth; avoid solvents
Safety	Turn amplifier off during installation; ensure correct polarity; avoid short circuits
Rotatable	Yes, via slide locks on pivots

Frequently Asked Questions - MAG06V3 SONANCE

How do I install the Sonance MAG06V3 speakers?

Install the FastMount brackets to the surface using included hardware. Run speaker wires through the bracket hole and speaker wire tunnel, then connect to the front terminals. Slide the speaker onto the bracket until locks snap. Ensure amplifier is off during connection.

Can these speakers be mounted on a pole?

Yes, use optional 2.5" U-bolts (sold separately) to attach the FastMount brackets to a pole. Refer to figure 5 in the manual.

What is the waterproof rating of the MAG06V3?

The speakers are rated IP-66 waterproof and conform to Mil Spec 810 for humidity, salt spray, temperature, and UV exposure, suitable for outdoor use.

What gauge speaker wire should I use?

The spring connectors accept wire up to 14 AWG. For best performance, use 14-16 AWG stranded wire.

Can I use these speakers indoors?

Yes, they are designed for outdoor use but can be used indoors. They are weather-resistant but not required for indoor environments.

How do I connect the speaker wires?

Strip about 0.5" of insulation, press down on the spring connector top, insert the wire, and release. Ensure correct polarity: amplifier '+' to speaker '+', amplifier '-' to speaker '-'.

What is the warranty period for the MAG06V3?

Sonance provides a one (1) year limited warranty from the original purchase date, covering defects in workmanship and materials. Proof of purchase required.

How should I clean the speakers?

Use a damp cloth to clean the exterior. Do not use solvents or abrasive cleaners as they may damage the finish.

Can I rotate the speakers after mounting?

Yes, unlock the slide locks by moving them toward the rear of the speaker, rotate to the desired position, then lock by sliding toward the front.

What is included in the box?

The package includes: (2) Sonance MAG06V3 speakers, (2) speaker grilles, (2) mounting brackets, (2) wire terminal covers, and a set of mounting hardware.

USER MANUAL MAG06V3 SONANCE

Technical line drawing of a speaker or audio device casing with mounting holes and central speaker (no text or symbols)

Scan QR Code for product installation video

Thank you for purchasing Sonance MAGO6V3 weather-resistant speakers.

When properly installed, these speakers will give you many years of outdoor entertainment pleasure. To get the most out of your new speakers, please read this manual thoroughly before you begin installation.

BOX & CONTENTS

(2) Sonance MAGO6V3 speakers
(2) Speaker grilles
(2) Mounting brackets
(2) Wire terminal covers
(1) Set of mounting hardware

SPEAKER PLACEMENT

Sonance MAGO6V3 Speakers are highly weather-resistant, and when mounted outdoors will perform exceptionally well for years even under adverse weather conditions.

The Sonance FastMount ^® bracket system makes it easy to mount the speakers in a variety of positions and locations: (see figure 1).

The best performance is obtained by placing the speakers at ear level, facing the listeners.

- If you are mounting the speakers above or below ear level, pivot them up or down to direct the sound towards the listeners.

Against a wall (flush)

Pole mount (hardware sold separately)

Simple line drawing of a house roof structure with no text or symbols

In a corner

Under an eave
FIGURE 1: SPEAKER PLACEMENT

CONNECTING & ASSEMBLING

WARNING: TURN THE AMPLIFIER'S POWER OFF UNTIL YOU HAVE COMPLETED ALL OF THE CONNECTIONS AND HAVE DETERMINED THAT THEY ARE CORRECT. (IF THE AMP'S AC PLUG IS ACCESSIBLE WE RECOMMEND THAT YOU UNPLUG IT FROM THE WALL OUTLET TO AVOID ACCIDENTAL TURN-ON AND POSSIBLE DAMAGE TO THE AMPLIFIER.)

1. In most cases you will be able to attach the FastMount brackets directly to the mounting surface. Run the speaker wires from the amplifier to the speaker locations and through the holes in the brackets (see figure 2).

NOTE: TO INCREASE WATER RESISTANCE AND MAKE INSTALLATION EASIER, THE SPEAKER WIRE TERMINALS ARE LOCATED ON THE MAGO6 SPEAKERS' FRONT PANEL. BE SURE TO LEAVE ENOUGH WIRE AT THE SPEAKER LOCATION TO FEED THROUGH THE TUNNEL IN THE SPEAKER ENCLOSURE AND CONNECT TO THE TERMINALS ON THE FRONT.

1. Attach the FastMount brackets to the mounting surface using the included hardware that is appropriate for the type of surface (see figure 3).
   If the installation requires that the speaker be mounted in a corner, attach the bracket with hardware through the slots in the angled corners (see figure 4).
2. If the installation requires that the speaker be mounted on a pole you can attach the FastMount brackets to the pole using 2.5" U-bolts (not included) (see figure 5).

3. Feed the speaker wires from the bracket into the wire entry grommet on the back of the speaker, through the wire tunnel and out the opening on the speaker's front panel (see figure 6).

4. The grommet forms a water-resistant seal around the speaker wire.

5. Make sure there is enough slack in the wire to allow the speaker to pivot on the bracket.

6. Slide the speaker onto the bracket until the locks snap into place. Pull enough wire through the front of the speaker to allow connection to the terminals (see figure 7).

FIGURE 2: PASS WIRE THROUGH HOLE

FIGURE 3: ATTACH BRACKET

FIGURE 4: CORNER MOUNTING

FIGURE 5: ATTACHING THE BRACKET TO A POLE

Pure technical diagram of a mechanical component with no text or symbols

FIGURE 6: WIRE ENTRY GROMMET

Technical line drawing of a speaker and mechanical bracket assembly (no text or symbols)

Technical line drawing of a mechanical device with mounting holes and central housing (no text or symbols)

FIGURE 7: ATTACH SPEAKERS TO BRACKETS

1. Connect the speaker wires to the speaker's terminals:

A. Strip about .5" of insulation from each conductor and twist the strands together or tin them with solder.

B. Press-down on the tops of the connectors to open them.

C. Insert the wires into the connector holes (see figure 8).

D. Release the connectors.

FIGURE 8: CONNECTION TERMINALS

- The spring connectors can accept wire up to 14 gauge.

- Double-check that you connected all of the wires properly (amplifier ‘+’ to speaker ‘+’; amplifier ‘-’ to speaker ‘-’) at all connections.

IMPORTANT: BE SURE NOT TO LET ANY STRAY ‘+’ AND ‘-’ WIRES TOUCH EACH OTHER. TOUCHING WIRES CAN CAUSE A SHORT- CIRCUIT THAT COULD DAMAGE YOUR AMPLIFIER.

1. Fit the wiring connector cover into the recess in the speaker's front panel. The cover should fit tightly but can be removed and replaced if the speaker needs to be disconnected (see figure 9).

2. Fit the grille onto the speaker (see figure 10).

Technical line drawing of a speaker with visible sound waves and a small inset component (no text or symbols)

FIGURE 9: ATTACH THE CONNECTOR COVER

Technical line drawing of a speaker module with no visible text or symbols

FIGURE 10: ATTACH THE GRILLE

You can rotate the speaker in the bracket to direct the sound toward the listeners.

1. Unlock the slide locks on the speaker pivots by moving them toward the rear of the speaker (see figure 11).
2. Rotate the speakers to the desired position.
3. Lock the slide locks by moving them toward the front of the speaker.

LOCK (toward front of speaker)

SPECIFICATIONS

MAGO6V3 Speakers

Tweeter: 1" (25mm) cloth dome, Ferrofluid cooled, in acoustic back chamber

Woofer: 6.5" (165mm) glass fiber cone with a Santoprene surround

Frequency Response: 65Hz - 30kHz ±3dB

Impedance: 8 ohms nominal; 6 ohms minimum

Power Handling: 5 watts minimum; 80 watts maximum

Sensitivity: 89dB SPL (2.83V/1 meter)

Environmental: Conforms to Mil Spec 810 for humidity, salt spray, temperature and UV, IP-66 waterproof rating

Environment Temp: -13^ - 149^ F ( -25^ C - 65^ C)

Dimensions (WxHxD): 7.51" x 12.14" x 6.86" (191mm x 308mm x 174mm)

Grille: Perforated aluminum

Shipping Weight: 14 lbs. (6.4kg) pair

LIMITED ONE (1) YEAR WARRANTY

Sonance warrants to the first end-user purchaser that this Sonance-brand product (product), when purchased from an authorized Sonance Dealer/Distributor, will be free from defective workmanship and materials for the period stated above. Sonance will at its option and expense during the warranty period, either repair the defect or replace the Product with a new or remanufactured Product or a reasonable equivalent.

EXCLUSIONS

TO THE EXTENT PERMITTED BY LAW, THE WARRANTY SET FORTH ABOVE IS IN LIEU OF, AND EXCLUSIVE OF, ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED BY SONANCE. ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY, IMPLIED WARRANTY OF FITNESS FOR USE, AND IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED.

No one is authorized to make or modify any warranties on behalf of Sonance. The warranty stated above is the sole and exclusive remedy and Sonance's performance shall constitute full and final satisfaction of all obligations, liabilities and claims with respect to the Product.

IN ANY EVENT, SONANCE SHALL NOT BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL, ECONOMIC, PROPERTY, BODILY INJURY, OR PERSONAL INJURY DAMAGES ARISING FROM THE PRODUCT, ANY BREACH OF THIS WARRANTY OR OTHERWISE.

This warranty statement gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion of implied warranties or limitations of remedies, so the above exclusions and limitations may not apply. If your state does not allow disclaimer of implied warranties, the duration of such implied warranties is limited to period of Sonance's express warranty.

Your Product Model and Description: Sonance MAG06V3 speakers

Warranty Period for this Product: One (1) year from the date on the original sales receipt or invoice or other satisfactory proof of purchase.

ADDITIONAL LIMITATIONS AND EXCLUSIONS FROM WARRANTY COVERAGE

The warranty described above is non-transferable, applies only to the initial installation of the Product, does not include installation of any repaired or replaced Product, does not include damage to allied or associated equipment which may result for any reason from use with this Product, and does not include labor or parts caused by accident, disaster, negligence, improper installation, misuse (e.g. overdriving the amplifier or speaker, excessive heat, cold or humidity), or from service or repair which has not been authorized by Sonance.

OBTAINING AUTHORIZED SERVICE

To qualify for the warranty, you must contact your authorized Sonance Dealer/Installer or call Sonance Customer Service at [phone] within the warranty period, must obtain a return merchandise number (RMA), and must deliver the Product to Sonance shipping prepaid during the warranty period, together with the original sales receipt, or invoice or other satisfactory proof of purchase.

SONANCE

©2020 Sonance. All rights reserved.

Due to continuous product improvement, all features and specifications are subject to change without notice.

For the latest Sonance product specification information visit our website: www.sonance.com

SONANCE • 991 Calle Amanecer • San Clemente, CA 92673 USA

[phone] • FAX: [phone] • Technical Support: [phone]

www.sonance.com