HF 6C2F0PX-80 - Dishwasher HOOVER - Free user manual and instructions
Find the device manual for free HF 6C2F0PX-80 HOOVER in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Dishwasher |
| Brand | Hoover |
| Model | HF 6C2F0PX-80 |
| Installation Type | Freestanding |
| Width | 60 cm |
| Height | 85 cm |
| Depth | 60 cm |
| Net Weight | 45 kg |
| Place Settings | 13 |
| Energy Class | E (EU) |
| Annual Energy Consumption | 295 kWh |
| Water Consumption per Cycle | 10.5 L |
| Noise Level | 44 dB(A) |
| Programs | Eco, Intensive, Daily, Quick 30 min, Glass |
| Delay Start | Up to 24 hours |
| Display | LED |
| Safety Features | Child lock, Anti-flood system |
| Maintenance | Clean filters regularly, check spray arms |
| Spare Parts Availability | Yes, through Hoover service |
Frequently Asked Questions - HF 6C2F0PX-80 HOOVER
How do I install the dishwasher?
Ensure the dishwasher is placed on a level surface. Connect the water inlet hose to a cold water supply (3/4 inch thread) and the drain hose to a suitable drain. Plug into a grounded outlet. Refer to the manual for detailed installation steps.
What should I do if the dishwasher doesn't start?
Check that the door is properly closed and latched. Verify the device is plugged in and the circuit breaker is on. Ensure the water supply is open and the delay start feature is not activated.
How to clean the filters?
Turn off the dishwasher and remove the lower rack. Unscrew the cylindrical filter and lift out the flat filter. Rinse them under running water with a soft brush. Reassemble in reverse order. Clean monthly.
What does the error code E1 mean?
Error code E1 indicates a water inlet issue. Check that the water tap is fully open, the inlet hose is not kinked, and the inlet filter is clean. If the problem persists, contact service.
Can I use regular dish soap?
No, use only specially formulated dishwasher detergent (powder, gel, or tablets). Regular dish soap will cause excessive foam and may damage the appliance.
How to adjust the rinse aid dosage?
Open the rinse aid dispenser lid. Use the dial to set the dosage from 1 (minimum) to 6 (maximum). Start with a medium setting and adjust based on drying results.
Why are dishes still wet after a cycle?
Ensure the rinse aid is filled and the dosage is adequate. Select a program with a drying phase (e.g., Eco). Check that the load is not blocking the vent and the water softener settings are correct for your water hardness.
What is the maximum load capacity?
The dishwasher can hold up to 13 place settings. For best results, do not overload and arrange items to allow water spray to reach all surfaces.
How to replace the rubber seal?
Purchase a genuine Hoover replacement seal. Remove the old seal by pulling it out from the groove. Clean the groove and press the new seal evenly into place. Ensure the seal is not twisted.
What is the energy consumption?
The annual energy consumption is approximately 295 kWh based on 280 standard cycles. The most efficient program (Eco) uses less energy. Refer to the energy label for details.
User questions about HF 6C2F0PX-80 HOOVER
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Dishwasher in PDF format for free! Find your manual HF 6C2F0PX-80 - HOOVER and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. HF 6C2F0PX-80 by HOOVER.