SuperServer SYS-220BT-HNC9R - Server Supermicro - Free user manual and instructions
Find the device manual for free SuperServer SYS-220BT-HNC9R Supermicro in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Server |
| Brand | Supermicro |
| Model | SuperServer SYS-220BT-HNC9R |
| Form Factor | 2U Rackmount |
| Dimensions (Height x Width x Depth) | 3.5 in (8.9 cm) x 17.2 in (43.7 cm) x 25.6 in (65 cm) |
| Weight | Approximately 45 lbs (20.4 kg) |
| Processor Support | Dual Intel Xeon Scalable (3rd Gen) |
| Memory Support | Up to 4TB DDR4 ECC Registered, 32 DIMM slots |
| Storage | Up to 24 x 2.5" hot-swap drive bays (SAS/SATA/NVMe) |
| Expansion Slots | Up to 6 PCIe 4.0 x16 slots |
| Power Supply | Redundant 1600W Platinum (1+1) |
| Cooling | 4 x 80mm hot-swap fans |
| Management | IPMI 2.0, Supermicro Server Manager |
| Networking | Dual 10GbE SFP+ and Dual 1GbE |
| Operating Temperature | 10°C to 35°C (50°F to 95°F) |
| Operating Humidity | 8% to 90% (non-condensing) |
| Maintenance | Clean regularly with compressed air; avoid liquid cleaners |
| Safety | Use anti-static wrist strap; disconnect power before servicing |
| Spare Parts & Repairability | Hot-swappable power supplies, fans, and drives; FRU list available |
Frequently Asked Questions - SuperServer SYS-220BT-HNC9R Supermicro
How to install hard drives in the SuperServer SYS-220BT-HNC9R?
To install hard drives, remove the drive carrier from the bay, attach the drive to the carrier with screws, then insert the carrier back into the bay until it clicks. Ensure the hot-swap handles are fully closed.
How to reset the IPMI password?
To reset the IPMI password, connect to the IPMI via SSH or web interface, navigate to user management, and reset the password. If locked, use the IPMI reset jumper on the motherboard or clear the CMOS.
How to update the BIOS?
To update the BIOS, download the latest BIOS file from Supermicro's website, copy it to a USB drive, boot into the BIOS setup utility, and use the flash tool (e.g., AMIFlash).
How to configure RAID?
To configure RAID, boot into the RAID BIOS (usually by pressing Ctrl-R during POST), create a virtual disk by selecting drives and setting RAID level, then save and exit.
How to connect to the IPMI web interface?
To connect to the IPMI web interface, find the IP address (via DHCP or front panel display), open a browser, enter the IP address, and log in with default credentials (admin/admin). Change the password immediately.
How to replace a failed power supply?
To replace a failed power supply, check the LED indicator (amber means failure), unplug the AC cord, press the release latch, slide out the PSU, insert a new unit, and reconnect power. It is hot-swappable.
What is the maximum memory capacity?
The maximum memory capacity is 4TB using 128GB DDR4 ECC LRDIMMs across 32 slots.
How to clear CMOS?
To clear CMOS, locate the CMOS clear jumper on the motherboard (typically near the battery), move it to the clear position for 10 seconds, then return to normal. Alternatively, remove the battery for a few minutes.
How to set up remote management?
To set up remote management, enable IPMI in BIOS, configure network settings, and access via the web interface or tools like SuperServer Manager.
How to check system temperatures?
To check system temperatures, use the IPMI web interface (Sensor Readings) or command-line tools like ipmitool sdr. The mainboard sensors show CPU, memory, and ambient temps.
User questions about SuperServer SYS-220BT-HNC9R Supermicro
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual SuperServer SYS-220BT-HNC9R - Supermicro and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SuperServer SYS-220BT-HNC9R by Supermicro.