RM/426 - Water dispenser Ramtons - Free user manual and instructions

Brand	Ramtons
Model	RM/426
Product Type	Water Dispenser (Hot & Cold)
Installation Type	Countertop / Floor Standing
Water Supply	Top-loading bottle (5-gallon or similar)
Hot Water Temperature	85-95°C (heating); automatic warm-keeping at 80°C
Cold Water Temperature	5-10°C
Heating Power	500W (estimated based on common models)
Cooling Power	100W (estimated)
Power Supply	220-240V, 50/60Hz, grounded outlet
Indicators	Power (yellow), Heating (red), Cooling (green) LEDs
Controls	Heating switch (red), Cooling switch (green)
Dimensions (approx.)	100 cm height x 30 cm width x 30 cm depth (estimate)
Weight (approx.)	10-15 kg (estimate)
Cooling System	Compressor-based
Safety Features	Ground wire; do not operate heating without water; automatic thermostat cut-off; child safety not specified
Maintenance	Drain hot and cold tanks when not in use; clean with water-soaked soft cloth; use 2% citric acid solution for descaling
Installation Clearance	2 inches (5 cm) from wall for air circulation
Operating Ambient Temperature	10-42°C

Frequently Asked Questions - RM/426 Ramtons

How should I prepare the water dispenser before first use?

Let the dispenser stand upright for about 2 hours after unpacking. Then, before plugging in, fill the water tank with tap water, wait 5 minutes, and press the hot water faucet until water flows out. This flushes the system.

What do the indicator lights mean?

The yellow LED indicates power is on. The red LED lights when heating is active and turns off when hot water reaches 85-95°C. The green LED lights when cooling is active and turns off when cold water reaches 5-10°C.

Can I adjust the temperature settings?

No, the temperatures are preset at the factory. The dispenser automatically maintains hot water at about 85-95°C and cold water at 5-10°C.

What should I do if no water comes out of the cold faucet?

Turn off the cooling switch and wait until water flows from the cold faucet, then turn the cooling switch back on. This prevents the cooling system from running without water.

How do I drain the dispenser if not using for a long time?

After the hot water cools, unplug the unit. Remove the drain cap on the back to drain the hot tank, then open the cold water faucet to drain the cold tank. Tighten the cap after draining.

Why should I not turn on the heating switch when there is no water?

Operating the heater without water can damage the heating element and create a safety hazard. Always ensure water is present before turning on the heating switch.

How should I clean the water dispenser?

Unplug and use a soft cloth dampened with water to wipe the exterior. Do not use harsh detergents or spray water directly. For internal cleaning, use a 2% citric acid solution in the hot water tank for about two hours, then rinse.

What is the recommended clearance around the dispenser?

Allow at least 2 inches (5 cm) of space between the dispenser and the wall for proper air circulation to the compressor.

What type of power outlet is required?

Use a properly grounded, exclusive wall outlet. Do not remove the ground prong from the power cord. For any power/grounding questions, consult a qualified electrician.

What should I do if the power supply cord is damaged?

The cord must be replaced with a special cord obtainable from our Service Center. Do not attempt to repair it yourself.

USER MANUAL RM/426 Ramtons

PRODUCT AND DESCRIPTION

1. top cover
2. hot water faucet
3. condenser
4. heating indicator
5. water receptacle
6. heating switch (red)
7. power indicator
8. front door
9. cooling switch (green)
10. cooling indicator
11. hot water drain
12. refrigerator switch
13. cold water faucet
14. power supply cord 15. legs

WIRING DIAGRAM

INSTALLATION GUIDELINES

• Remove the exterior and interior packing.
• Place your appliance on a floor that is strong enough to support the dispenser when it is fully loaded. The unit is provided with four plastic feet. If it does not sit level on the floor, adjust the front feet to level the unit well to the floor.
• Locate the appliance away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Extreme cold ambient temperatures may also cause the appliance not to perform properly.
• Allow 2 inches of space between the water dispenser and the wall, which allows for proper air circulation to cool the compressor.
• Plug the appliance into an exclusive properly installed-grounded wall outlet. Do not cut or remove the third (ground) prong from the power cord under any circumstances. Any questions concerning power and/or grounding should be directed toward a certified electrician or an authorized products service center.
  ● This water dispenser is not recommended for outdoor usage.
• Do not locate the dispenser in the area where the temperature may fall below freezing point (0°C or 32°F).
• Keep area around dispenser free of dust and dirt.
• Keep the reserve supply of water bottles away from excessive heat and light.

PRE-OPERATION INSTRUCTIONS

• Before connecting the appliance to the power source. Let it stand upright for approximately 2 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation.
• Check and make sure the backside hot water drainage hole cap is not leaked or broken.
• The water dispenser is pre-cleaned at the factory but the reservoir and water lines must be flushed with fresh water before use as follows:
• Keep the unit unplugged.
  ● Fill water tank with tap water full to capacity. Wait for 5 minutes until water settles.
  ● Push the hot water faucet until water comes out, then stop the faucet.

OPERATION

● Ambient temperature: 10 \~ 42°C

● Atmosphere 86 \~ 106kpa

- When using the bottles holding ultra-pure water, distilled water or space water with the so-called clever lid, tear off the hygienic label on the lid, place the bottles at the intake, then the core of water guard will automatically open the valve and seal it in the meantime, when moving the bottles, the valve will also seal automatically to avoid any possible oozing.

- Push the hot water faucet, bubbles are generated inside the bottle, indicating that water is flowing into hot water and cold water tanks, keep pressing the hot water valve until water flows out, dispensing cold water required need no particular adjustment.

- Do not connect the electrical power plug, until water comes out of the hot water faucet.

● After plug, the yellow LED indicator will be on indicating the power is "ON".

- Turn on the heating switch, the red LED indicator will be on and the heating system starts working. When the hot water comes up to 85-95°C or so, the red light goes off, the heating system stops working. The machine turns to the warm-keeping status. When the hot water temperature is lower than 80°C, the heating system will resume working automatically.

- Turn on the cooling switch, the green LED indicator will be on and the cooling system starts working. When the cold water falls down to 5-10°C, the green light goes off, the cooling system stops working. The machine turns to the cold-keeping status. When the cold water temperature goes up to a set degree, the cooling system will resume working automatically.

- Since the temperature has already been adjusted before leaving the factory, it is unnecessary for customers to set the temperature.

- Turn the heating and cooling switches on. Then the heating and cooling processes start working together.

- If the device is not applied for a long time, after the hot water cools down, please remove the power plug and revolve the drain cap to drain the rest water in the hot tank then tighten the cap. Open the cold water faucet to drain the rest water in the cold tank.

- If there is no water flowing from cooling faucet, please shut down the cooling switch until there is water flowing out.

- If you do not plan to use the water heating function for more than three days, we strongly recommend that you turn off the hot water function.

● Never turn on the heating switch when there is no water.
- When carrying it, the angle of inclination should be less than 45^ .
- Adopt the ground wire to avoid any electric shock.
- In the process of using, check the water receptacle frequently. If the water receptacle is full, please pour the water out in time.
- Do not turn on and off the “cooling” switch in three minutes to protect the compressor and extend the compressor usage life.

MAINTENANCE

• Remove power plug or disconnect from the mains before performing any maintenance or servicing the product.
  ● Never use detergent or chemicals harmful to health to clean the water tanks.
• Do not directly spray water on the surface of the product.
  ● Wipe the front and back of the product with water-soaked soft cloth.
• If dust of other exterior substance has accumulated on the condenser, wipe off with water-soaked soft cloth.
• After cleaning the product, completely dry it. Fill the water to the tanks until waters comes out of the hot water faucet, then connect the electric power plug. If the surface of the electric heater in the hot water tank is deposited by water deposition, heating capacity will decrease. Fill hot water tank with aqueous solution of 2% aitric acid and keep for about two hours then cleaning. If the problems can not be solved, contact your dealer or the Service Center of our company.
• If power supply cord on this device is damaged, it must be replaced with a special power supply cord that is obtainable at Service Center of our company.

TROUBLESHOOTING GUIDE

You can solve many common water dispenser problems easily, saving you the cost of a possible service call. Try the suggestions outlined below to see if you can solve them before calling the service center.

Problem Possible Reason

Water d'.....d...net.....M...d...